Not sure what the heck happened to this little guy (Zyxel NSA325) running I think debian v7x. I havent checked in on this guy in the last maybe 1 or 2 but when I did today I noticed i was able to ping it across my lan but that was it. No ports seemed to be open including ssh. WTF? I connected serial console via putty and get the below output during boot. Last entry is "/bin/sh: usbhid:: not found (initramfs)" I pasted the entire boot log if it helps.
It boots off of a Sandisk Cruzer Fit 16GB usb flash drive with two sata drives (raid1) via mdm. (hopefully still in tact. Im pretty sure they are. If not no biggy I have other backups of data.) I currently have the usb drive plugged into my windows machine and mounted using Paragon ExtFS for Windows so that I can read/write to the drive.
It boots off of a Sandisk Cruzer Fit 16GB usb flash drive with two sata drives (raid1) via mdm. (hopefully still in tact. Im pretty sure they are. If not no biggy I have other backups of data.) I currently have the usb drive plugged into my windows machine and mounted using Paragon ExtFS for Windows so that I can read/write to the drive.
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: DB-88F6282A-BP LE
U-Boot 1.1.4 (Sep 16 2011 - 17:51:53) Marvell version: 3.5.9
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFF00
Soc: 88F6282 A1CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 512MB
DRAM Total size 512MB 16bit width
Addresses 10M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (10M - 7M): Done
NAND:128 MB
Flash: 0 kB
CPU : Marvell Feroceon (Rev 1)
Kernel address is 0x4640000.
Streaming disabled
Write allocate disabled
USB 0: host mode
[BlueDBG] reseting SoC Pex[0] 0 ...
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
[BlueDBG] reseting SoC Pex[1] 0 ...
[BlueDBG] reseting SoC Pex[1] 1 ...
[BlueDBG] reseting SoC Pex[1] 2 ...
[BlueDBG] reseting SoC Pex[1] 3 ...
[BlueDBG] reseting SoC Pex[1] 4 ...
[BlueDBG] reseting SoC Pex[1] 5 ...
[BlueDBG] reseting SoC Pex[1] 6 ...
[BlueDBG] reseting SoC Pex[1] 7 ...
[BlueDBG] reseting SoC Pex[1] 8 ...
[BlueDBG] reseting SoC Pex[1] 9 ...
[BlueDBG] reseting SoC Pex[1] 10 ...
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
(Re)start USB...
USB: scanning bus for devices... 3 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
....
.
......
............
.........................
...................................................
......................................................................................................
................................................................
2756040 bytes read
....
.
......
............
.........................
...................................................
......................................................................................................
...................................................................................................................................................................................
...................................................................................................................................................
6032465 bytes read
## Booting image at 02000000 ...
Image Name: Linux-3.16.0-kirkwood-tld-2
Created: 2014-09-01 23:18:31 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2755976 Bytes = 2.6 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01100000 ...
Image Name: initramfs-3.16.0-kirkwood-tld-2
Created: 2014-09-01 23:18:48 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 6032401 Bytes = 5.8 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.16.0-kirkwood-tld-2 (root@tldDebian) (gcc version 4.6.3 (Debian 4.6.3-14) ) #2 PREEMPT Sun Aug 31 18:56:01 PDT 2014
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: ZyXEL NSA325 2-Bay Power Media Server
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] On node 0 totalpages: 131072
[ 0.000000] free_area_init_node: node 0, pgdat c07c303c, node_mem_map dfbfb000
[ 0.000000] DMA zone: 1024 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 131072 pages, LIFO batch:31
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
[ 0.000000] Kernel command line: console=ttyS0,115200=mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/sdb1 rw rootwait loglevel=8
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 505588K/524288K available (5441K kernel code, 397K rwdata, 1840K rodata, 257K init, 299K bss, 18700K reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB)
[ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc07248b0 (7283 kB)
[ 0.000000] .init : 0xc0725000 - 0xc0765444 ( 258 kB)
[ 0.000000] .data : 0xc0766000 - 0xc07c975c ( 398 kB)
[ 0.000000] .bss : 0xc07c975c - 0xc08144dc ( 300 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:114
[ 0.000008] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474836475ns
[ 19.947361] Console: colour dummy device 80x30
[ 19.947383] Calibrating delay loop... 1594.16 BogoMIPS (lpj=7970816)
[ 19.987181] pid_max: default: 32768 minimum: 301
[ 19.987274] Security Framework initialized
[ 19.987325] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 19.987338] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 19.988006] Initializing cgroup subsys devices
[ 19.988053] Initializing cgroup subsys freezer
[ 19.988074] Initializing cgroup subsys net_cls
[ 19.988109] Initializing cgroup subsys blkio
[ 19.988185] CPU: Testing write buffer coherency: ok
[ 19.988534] Setting up static identity map for 0x5273f0 - 0x527448
[ 19.990351] devtmpfs: initialized
[ 19.993340] prandom: seed boundary self test passed
[ 19.996336] prandom: 100 self tests passed
[ 19.996356] pinctrl core: initialized pinctrl subsystem
[ 19.996741] regulator-dummy: no parameters
[ 19.997109] NET: Registered protocol family 16
[ 19.997492] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 19.998428] cpuidle: using governor ladder
[ 19.998448] cpuidle: using governor menu
[ 19.998549] Kirkwood: MV88F6282-Rev-A1, TCLK=200000000.
[ 19.998567] Feroceon L2: Enabling L2
[ 19.998595] Feroceon L2: Cache support initialised.
[ 19.999053] initial MPP regs: 21111111 01103311 00051100 00000000 00000000 00000000 00000000
[ 19.999077] final MPP regs: 21111111 00003311 00051100 00000000 00000000 00000000 00000000
[ 20.000045] Kirkwood PCIe port 0: link up
[ 20.000054] PCI: bus0 uses PCIe port 0
[ 20.000203] PCI host bridge to bus 0000:00
[ 20.000218] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[ 20.000228] pci_bus 0000:00: root bus resource [io 0x1000-0xffff]
[ 20.000237] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 20.000267] pci 0000:00:00.0: [11ab:6282] type 00 class 0x058000
[ 20.000290] pci 0000:00:00.0: reg 0x10: [mem 0xf1000000-0xf10fffff 64bit pref]
[ 20.000304] pci 0000:00:00.0: reg 0x18: [mem 0x00000000-0x1fffffff]
[ 20.000347] pci 0000:00:00.0: supports D1 D2
[ 20.000513] pci 0000:00:01.0: [1033:0194] type 00 class 0x0c0330
[ 20.000549] pci 0000:00:01.0: reg 0x10: [mem 0x90000000-0x90001fff 64bit]
[ 20.000669] pci 0000:00:01.0: PME# supported from D0 D3hot
[ 20.000879] PCI: bus0: Fast back to back transfers disabled
[ 20.000892] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 20.000921] pci 0000:00:01.0: BAR 0: assigned [mem 0xe0000000-0xe0001fff 64bit]
[ 20.028382] vgaarb: loaded
[ 20.028649] usbcore: registered new interface driver usbfs
[ 20.028707] usbcore: registered new interface driver hub
[ 20.028803] usbcore: registered new device driver usb
[ 20.029571] Switched to clocksource orion_clocksource
[ 20.059540] NET: Registered protocol family 2
[ 20.060362] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 20.060417] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 20.060468] TCP: Hash tables configured (established 4096 bind 4096)
[ 20.060520] TCP: reno registered
[ 20.060530] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 20.060549] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 20.060715] NET: Registered protocol family 1
[ 20.060983] RPC: Registered named UNIX socket transport module.
[ 20.060991] RPC: Registered udp transport module.
[ 20.060996] RPC: Registered tcp transport module.
[ 20.061002] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 20.061097] PCI: CLS 32 bytes, default 32
[ 20.061318] Unpacking initramfs...
[ 20.432653] Freeing initrd memory: 5884K (c1101000 - c16c0000)
[ 20.432764] NetWinder Floating Point Emulator V0.97 (double precision)
[ 20.433672] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 20.433724] audit: initializing netlink subsys (disabled)
[ 20.433772] audit: type=2000 audit(0.480:1): initialized
[ 20.434412] zbud: loaded
[ 20.434619] VFS: Disk quotas dquot_6.5.2
[ 20.434662] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 20.435090] NFS: Registering the id_resolver key type
[ 20.435152] Key type id_resolver registered
[ 20.435159] Key type id_legacy registered
[ 20.435179] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 20.435189] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 20.435318] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 20.435554] msgmni has been set to 998
[ 20.435673] Key type big_key registered
[ 20.437453] alg: No test for stdrng (krng)
[ 20.437541] bounce: pool size: 64 pages
[ 20.437591] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 20.437605] io scheduler noop registered
[ 20.437616] io scheduler deadline registered
[ 20.437755] io scheduler cfq registered (default)
[ 20.438084] mv_xor mv_xor.0: Marvell shared XOR driver
[ 20.469626] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 20.509617] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 20.509749] mv_xor mv_xor.1: Marvell shared XOR driver
[ 20.549618] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[ 20.589614] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[ 20.589935] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 20.590659] console [ttyS0] disabled
[ 20.610699] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 12500000) is a 16550A
[ 21.318534] console [ttyS0] enabled
[ 21.323116] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1
[ 21.329496] nand: Samsung NAND 128MiB 3,3V 8-bit
[ 21.334150] nand: 128MiB, SLC, page size: 2048, OOB size: 64
[ 21.339847] Scanning device for bad blocks
[ 21.433945] Bad eraseblock 796 at 0x000006380000
[ 21.443505] Bad eraseblock 840 at 0x000006900000
[ 21.473741] Creating 9 MTD partitions on "orion_nand":
[ 21.478912] 0x000000000000-0x000000100000 : "uboot"
[ 21.484194] 0x000000100000-0x000000180000 : "uboot_env"
[ 21.489762] 0x000000180000-0x000000200000 : "key_store"
[ 21.495276] 0x000000200000-0x000000280000 : "info"
[ 21.500436] 0x000000280000-0x000000c80000 : "etc"
[ 21.505429] 0x000000c80000-0x000001680000 : "kernel_1"
[ 21.510897] 0x000001680000-0x000004640000 : "rootfs1"
[ 21.516264] 0x000004640000-0x000005040000 : "kernel_2"
[ 21.521755] 0x000005040000-0x000008000000 : "rootfs2"
[ 21.527747] libphy: Fixed MDIO Bus: probed
[ 21.542034] libphy: orion_mdio_bus: probed
[ 21.546241] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 21.555569] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:50:43:00:02:02
[ 21.564572] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 21.571167] ehci-pci: EHCI PCI platform driver
[ 21.575682] ehci-orion: EHCI orion driver
[ 21.579805] orion-ehci orion-ehci.0: EHCI Host Controller
[ 21.585246] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 21.593027] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 21.609601] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 21.615687] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 21.622524] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 21.629792] usb usb1: Product: EHCI Host Controller
[ 21.634689] usb usb1: Manufacturer: Linux 3.16.0-kirkwood-tld-2 ehci_hcd
[ 21.641434] usb usb1: SerialNumber: orion-ehci.0
[ 21.646642] hub 1-0:1.0: USB hub found
[ 21.650471] hub 1-0:1.0: 1 port detected
[ 21.655078] mousedev: PS/2 mouse device common for all mice
[ 21.969617] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 22.121038] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[ 22.127779] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 22.134969] usb 1-1: Product: USB2.0 Hub
[ 22.139730] hub 1-1:1.0: USB hub found
[ 22.143785] hub 1-1:1.0: 4 ports detected
[ 22.429913] usb 1-1.3: new high-speed USB device number 3 using orion-ehci
[ 22.540534] usb 1-1.3: New USB device found, idVendor=0781, idProduct=5571
[ 22.547446] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 22.554825] usb 1-1.3: Product: Cruzer Fit
[ 22.558955] usb 1-1.3: Manufacturer: SanDisk
[ 22.563275] usb 1-1.3: SerialNumber: 4C530007601029115103
[ 22.669597] rtc-mv rtc-mv: internal RTC not ticking
[ 22.674634] i2c /dev entries driver
[ 22.678562] rtc-pcf8563 0-0051: chip found, driver version 0.4.3
[ 22.685956] rtc-pcf8563 0-0051: rtc core: registered rtc-pcf8563 as rtc0
[ 22.692958] orion_gpio_is_valid: invalid GPIO 12
[ 22.698501] hidraw: raw HID events driver (C) Jiri Kosina
[ 22.704216] drop_monitor: Initializing network drop monitor service
[ 22.710699] TCP: cubic registered
[ 22.714039] NET: Registered protocol family 17
[ 22.718621] Key type dns_resolver registered
[ 22.723460] registered taskstats version 1
[ 22.729506] rtc-pcf8563 0-0051: setting system clock to 2016-08-13 05:36:10 UTC (1471066570)
[ 22.738677] PM: Hibernation image not present or could not be loaded.
[ 22.746134] Freeing unused kernel memory: 256K (c0725000 - c0765000)
Loading, please wait...
[ 22.810327] udevd[57]: starting version 175
[ 22.878399] xhci_hcd 0000:00:01.0: xHCI Host Controller
[ 22.937285] xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 2
[ 23.004884] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 23.025237] SCSI subsystem initialized
[ 23.045401] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 23.062289] usb-storage 1-1.3:1.0: USB Mass Storage device detected
[ 23.068792] libata version 3.00 loaded.
[ 23.088504] sata_mv sata_mv.0: version 1.28
[ 23.097072] usb usb2: Product: xHCI Host Controller
[ 23.117335] sata_mv sata_mv.0: cannot get optional clkdev
[ 23.125066] usb usb2: Manufacturer: Linux 3.16.0-kirkwood-tld-2 xhci_hcd
[ 23.131913] scsi0 : usb-storage 1-1.3:1.0
[ 23.147189] usbcore: registered new interface driver usb-storage
[ 23.160490] sata_mv sata_mv.0: slots 32 ports 2
[ 23.174563] usb usb2: SerialNumber: 0000:00:01.0
[ 23.187426] usbcore: registered new interface driver uas
[ 23.202820] hub 2-0:1.0: USB hub found
[ 23.206664] scsi1 : sata_mv
[ 23.220505] hub 2-0:1.0: 2 ports detected
[ 23.224601] scsi2 : sata_mv
[ 23.227661] ata1: SATA max UDMA/133 irq 21
[ 23.237045] xhci_hcd 0000:00:01.0: xHCI Host Controller
[ 23.242429] ata2: SATA max UDMA/133 irq 21
[ 23.246653] xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 3
[ 23.255263] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003
[ 23.262252] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 23.269506] usb usb3: Product: xHCI Host Controller
[ 23.274453] usb usb3: Manufacturer: Linux 3.16.0-kirkwood-tld-2 xhci_hcd
[ 23.281213] usb usb3: SerialNumber: 0000:00:01.0
[ 23.286779] hub 3-0:1.0: USB hub found
[ 23.290621] hub 3-0:1.0: 2 ports detected
[ 23.749610] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 23.809635] ata1.00: ATA-8: ST3250310NS, SN06, max UDMA/133
[ 23.815230] ata1.00: 488397168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 23.899637] ata1.00: configured for UDMA/133
[ 23.919879] scsi 1:0:0:0: Direct-Access ATA ST3250310NS SN06 PQ: 0 ANSI: 5
[ 24.130989] scsi 0:0:0:0: Direct-Access SanDisk Cruzer Fit 1.26 PQ: 0 ANSI: 6
[ 24.162406] sd 1:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[ 24.171721] sd 0:0:0:0: [sdb] 31266816 512-byte logical blocks: (16.0 GB/14.9 GiB)
[ 24.179568] sd 1:0:0:0: [sda] Write Protect is off
[ 24.184488] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 24.189756] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 24.198902] sd 0:0:0:0: [sdb] Write Protect is on
[ 24.205425] sd 0:0:0:0: [sdb] Mode Sense: 43 00 80 00
[ 24.211190] sd 0:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 24.224767] sdb: sdb1
[ 24.230692] sd 0:0:0:0: [sdb] Attached SCSI disk
[ 24.235468] sda: sda1
[ 24.239199] sd 1:0:0:0: [sda] Attached SCSI disk
[ 26.299612] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 26.339636] ata2.00: ATA-8: ST3250310NS, SN05, max UDMA/133
[ 26.345234] ata2.00: 488397168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 26.409636] ata2.00: configured for UDMA/133
[ 26.429855] scsi 2:0:0:0: Direct-Access ATA ST3250310NS SN05 PQ: 0 ANSI: 5
[ 26.439179] sd 2:0:0:0: [sdc] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[ 26.447571] sd 2:0:0:0: [sdc] Write Protect is off
[ 26.452409] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 26.457572] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 26.492199] sdc: sdc1
[ 26.495846] sd 2:0:0:0: [sdc] Attached SCSI disk
[ 26.534037] sd 1:0:0:0: Attached scsi generic sg0 type 0
[ 26.548619] sd 0:0:0:0: Attached scsi generic sg1 type 0
[ 26.554378] sd 2:0:0:0: Attached scsi generic sg2 type 0
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
[ 27.075987] EXT3-fs (sdb1): recovery required on readonly filesystem
[ 27.082432] EXT3-fs (sdb1): error: write access unavailable, cannot proceed
mount: mounting /dev/sdb1 on /root failed: Invalid argument
Begin: Running /scripts/local-bottom ... done.
done.
Begin: Running /scripts/init-bottom ... mount: mounting /dev on /root/dev failed: No such file or directory
done.
Target filesystem doesn't have requested /sbin/init.
No init found. Try passing init= bootarg.
modprobe: module i8042 not found in modules.dep
[ 27.198979] uhci_hcd: USB Universal Host Controller Interface driver
[ 27.211339] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 27.224085] usbcore: registered new interface driver usbhid
[ 27.229792] usbhid: USB HID core driver
BusyBox v1.20.2 (Debian 1:1.20.0-7) built-in shell (ash)
Enter 'help' for a list of built-in commands.
/bin/sh: can't access tty; job control turned off
(initramfs) usbhid: USB HID core driver
/bin/sh: usbhid:: not found
(initramfs)