Debian on Verbatim MediaShare Mini (9 replies)

Trying to get Debian to boot on Verbatim MediaShare Mini and I can't seem to get the Ethernet recognized. This uses a USI Topkick0281 board which should be a variation of the same board used in the TonidoPlug. See my entry @ wikidevi for complete hardware details. The board uses a Marvell 88F6281 A1 and does not appear to support kwboot as I've unsuccessfully tried multiple times. I've tried booting into a Debian 4.4 USB disk prepared with the kirkwood-pogo_e02.dts and the kirkwood-sheevaplug.dts which appear to be closest match to the features, but both result in unrecognized eth0.

Below is the u-boot log:

         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_ 
| | | |___|  _ \ / _ \ / _ \| __| 
| |_| |___| |_) | (_) | (_) | |_ 
 \___/    |____/ \___/ \___/ \__| 
 ** MARVELL BOARD: DB-88F6281A-BP LE 
The board type is Topkick0281


U-Boot 1.1.4 (Jul 13 2010 - 12:04:50) Marvell version: 3.4.27
USISH-SMB Ver: topkick0281-20100706-axentra

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006D0120

Soc: 88F6281 A1 (DDR2)
CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 200Mhz , TClock = 166Mhz 

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 256MB 
DRAM Total size 256MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB
Flash:  0 kB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled 
Write allocate disabled

USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0 
Marvell>>  printenv^M
baudrate=115200
loads_echo=0
ipaddr=192.168.58.21
serverip=192.168.58.135
rootpath=/mnt/ARM_FS/
netmask=255.255.255.0
run_diag=yes
CASset=min
ethprime=egiga0
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
nandEcc=1bit
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
ethact=egiga0
bootargs=console=ttyS0,115200;version=topkick0281-002-001-20100701-verbatim
initializeKernelRamdisk=run initializeUSB; nand erase clean 0x200000 0x600000; nand write.e 0x1200000 0x200000 0x300000; nand erase clean 0x800000 0x1000000; nand write.e 0x1800000 0x800000 0x800000
filesize=61123C
ethaddr=00:27:13:ff:f1:f3
PK=VPRQ-FPTA-NWKT-QWWR
console=console=ttyS0,115200
initializeDev=run initializeKernel; setenv bootargs console=ttyS0,115200 root=/dev/ram0 rw ramdisk=0x01100000,8M install_type=nand; bootm 0x00800000 0x01100000
initializeKernel=run initializeUSB; nand erase clean 0x00200000 0x00600000; nand write.e 0x00800000 0x00200000 0x00600000
initializeUSB=usb start; fatload usb 0 0x00800000 uImage; fatload usb 0 0x01100000 initrd
save_crc=true
install_mode=false
bootargs_root=ubi.mtd=2,2048 root=ubi0:rootfs rootfstype=ubifs init=/linuxrc
console2=console=ttyS0,115200
bootcmd=nand read.e 0x800000 0x200000 0x600000; setenv bootargs $(console2) $(bootargs_root); bootm 0x800000
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
enaAutoRecovery=yes
pcieTune=no

Environment size: 1920/131068 bytes
Marvell>> help^M
?       - alias for 'help'
SatR - sample at reset sub-system, relevent for DB only
base    - print or set address offset
boot    - boot default, i.e., run 'bootcmd'
bootd   - boot default, i.e., run 'bootcmd'
bootext2    dev:boot_part1,boot_part2 addr boot_image linux_dev_name 
bootm   - boot application image from memory
bootp   - boot image via network using BootP/TFTP protocol
bubt    - Burn an image on the Boot Nand Flash.
chpart  - change active partition
cmp     - memory compare
cmpm    - Compare Memory
cp      - memory copy
cpumap - Display CPU memory mapping settings.
crc32   - checksum calculation
date    - get/set/reset date & time
dclk    - Display the MV device CLKs.
dhcp    - invoke DHCP client to obtain IP/boot params
diskboot- boot from IDE device
echo    - echo args to console
eeprom  - EEPROM sub-system
erase   - erase FLASH memory
ext2load- load binary file from a Ext2 filesystem
ext2ls  - list files in a directory (default /)
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls   - list files in a directory (default /)
fi      - Find value in the memory.
flinfo  - print FLASH memory information
fsinfo  - print information about filesystems
fsload  - load binary file from a filesystem image
g       - start application at cached address 'addr'(default addr 0x40000)
go      - start application at address 'addr'
help    - print online help
icrc32  - checksum calculation
ide     - IDE sub-system
iloop   - infinite loop on address range
imd     - i2c memory display
iminfo  - print header information for application image
imm[.b, .s, .w, .l]     - i2c memory modify (auto-incrementing)
imw     - memory write (fill)
inm     - memory modify (constant address)
iprobe  - probe to discover valid I2C chip addresses
ir      - reading and changing MV internal register values.
loop    - infinite loop on address range
ls      - list files in a directory (default /)
map     - Diasplay address decode windows
md      - memory display
me      - PCI master enable
mm      - memory modify (auto-incrementing)
mmcinit - init mmc card
mp      - map PCI BAR
mtdparts- define flash/nand partitions
mtest   - simple RAM test
mw      - memory write (fill)
nand                   - NAND sub-system
nboot   - boot from NAND device
nbubt   - Burn a boot loader image on the Boot Nand Flash.
nm      - memory modify (constant address)
pci     - list and access PCI Configuration Space
phyRead - Read PCI-E Phy register
pciePhyWrite    - Write PCI-E Phy register
phyRead - Read Phy register
phyWrite        - Write Phy register
ping    - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
rcvr    - Satrt recovery process (Distress Beacon with TFTP server)
reset   - Perform RESET of the CPU
resetenv        - Return all environment variable to default.
run     - run commands in an environment variable
saveenv - save environment variables to persistent storage
se      - PCI Slave enable
setenv  - set environment variables
sflash  - read, write or erase the external SPI Flash.
sg      - scanning the PHYs status
sp      - Scan PCI bus.
switchRegRead   - Read switch register
switchRegWrite  - Write switch register
tftpboot- boot image via network using TFTP protocol
usb     - USB sub-system
usbboot - boot from USB device
version - print monitor version
Marvell>>

Any ideas on what to try in order get access to Ethernet?