Attempt to restore Pink Pogoplug e02 to factory corrupt uboot. Where to go from here? (7 replies)

So i got Linux and everything up running successfully until i got to setting up the DLNA streaming server and things went downhill from there. Needless to say i thought after the mess i had made i should just start from scratch and went about trying to figure out how to flash the pogo back to stock. I ran this command from the original pogoplug software environment(booted without the linux usb)

/usr/local/cloudengines/bin/./blparam 'bootcmd=run bootcmd_original"

After that the pogo would no longer boot with or without the flash drive and i cannot ssh into it. So i now have a serial connection established and get the following output on boot.

U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02

SoC:   Kirkwood 88F6281_A0
DRAM:  256 MiB
WARNING: Caches not enabled
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot:  0
(Re)start USB...
USB:   Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported

** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "mtd=3"
UBI: MTD device size:            91 MiB
UBI: number of good PEBs:        728
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     0
UBI: available PEBs:             717
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: ........ done.
### JFFS2 load complete: 524288 bytes loaded to 0x800000
## Starting application at 0x00800200 ...


U-Boot 1.1.4 (Sep 28 2009 - 11:55:23) Cloud Engines v2.0 (3.4.16)

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 00690D60

Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 256MB
DRAM Total size 256MB  16bit width
Flash:  0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:128 MB

CPU : Marvell Feroceon (Rev 1)
CLOUD ENGINES BOARD: PPV2

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0 [PRIME], egiga1
Hit any key to stop autoboot:  0
## Error: "bootcmd_original
/usr/local/cloudengines/bin/./blparam" not defined
CE>>

Can someone please direct me from here how i can reflash the original pogoplug boot/software? I just want to get it back to factory settings so i can restart the project! I am not very strong with Linux coding so i have been having trouble figuring out where to go next with my google searching. Thank you very much in advance!!!