NSA325V2 - Installation of Debian-4.4.0-kirkwood-tld-1-rootfs fails (3 replies)

Hello everyone,

this is my third thread in order to update my NSA325v2 - it seems, I've no luck with this box... :/

Anyways, I'm trying to install Debian 4.4.0 rootfs, in order to be able to install the newest U-Boot - seeNSA325V2 u-boot installation - Problem with permission denied.

In order to install Debian 4.4.0 rootfs, i've followed the instructions on http://forum.doozan.com/read.php?2,12096, starting from "Updated 20 Feb 2016:".

I've done the following steps:

1. Format a new USB drive with a single Ext3 partition, and label it rootfs. In addition, I've set the bootflag for this partition.
cd /media/sdb1 
tar -xjf Debian-4.4.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2
Adjust fstab. ext2 -> ext3
Generate the uImage with DTB embedded inside: 
cd /media/sdb1/boot
cp -a zImage-4.4.0-kirkwood-tld-1  zImage.fdt
cat dts/kirkwood-goflexnet.dtb  >> zImage.fdt
mv uImage uImage.orig
mkimage -A arm -O linux -T kernel -C none -a 0x00008000 -e 0x00008000 -n Linux-4.4.0-kirkwood-tld-1 -d zImage.fdt  uImage
sync
Done. Take this USB rootfs to your plug and cold start.

My NAS isn't booting. The bootlog is:

         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|
 ** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Jul 18 2013 - 10:47:29) Marvell version: 3.5.9

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CFB00

Soc: 88F6282 A1CPU running @ 1600Mhz L2 running @ 800Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 8 tRAS = 24 tRCD=8
DRAM CS[0] base 0x00000000   size 512MB
DRAM Total size 512MB  16bit width
Addresses 10M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (10M - 7M): Done
NAND:128 MB
Flash:  0 kB

CPU : Marvell Feroceon (Rev 1)
Kernel address is 0xc80000.

Streaming disabled
Write allocate disabled


USB 0: host mode
        [BlueDBG] reseting SoC Pex[0]  0 ...
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
        [BlueDBG] reseting SoC Pex[1]  0 ...
        [BlueDBG] reseting SoC Pex[1]  1 ...
        [BlueDBG] reseting SoC Pex[1]  2 ...
        [BlueDBG] reseting SoC Pex[1]  3 ...
        [BlueDBG] reseting SoC Pex[1]  4 ...
        [BlueDBG] reseting SoC Pex[1]  5 ...
        [BlueDBG] reseting SoC Pex[1]  6 ...
        [BlueDBG] reseting SoC Pex[1]  7 ...
        [BlueDBG] reseting SoC Pex[1]  8 ...
        [BlueDBG] reseting SoC Pex[1]  9 ...
        [BlueDBG] reseting SoC Pex[1]  10 ...
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
(Re)start USB...
USB:   scanning bus for devices... 3 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found

** Unable to read "/uImage" from usb 0:1 **

** Unable to read "/uInitrd" from usb 0:1 **
## Booting image at 02000000 ...
Bad Magic Number
Marvell>>

The USB card is located in the left rear USB slot, when seen from behind. I've adjusted the boot envs as bescribed here, but no luck

Marvell>> printenv
bootdelay=2
baudrate=115200
loads_echo=0
ipaddr=10.4.52.165
serverip=10.4.52.7
rootpath=/srv/ubuntu
netmask=255.255.255.0
nandEcc=1bit
MODEL_ID=AE03
PRODUCT_NAME=NSA-325v2
FEATURE_BIT=00
CONTRY_TYPE=FF
VENDOR_NAME=MitraStar Technology Corp.
run_diag=yes
console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root)
ethprime=egiga0
bootargs_root=root=/dev/nfs rw
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
lcd0_enable=0
lcd0_params=640x480-16@60
ethaddr=00:50:43:00:02:02
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
image_multi=yes
ethact=egiga0
arcNumber=4495
bootargs_stock=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
bootcmd_linux=setenv bootargs $(bootargs_linux); mw.l f1010100 0020c000; usb reset; ext2load usb 0:1 $(loadaddr) /uImage; ext2load usb 0:1 0x01100000 /uInitrd; bootm $(loadaddr) 0x01100000
bootcmd_stock=setenv bootargs $(bootargs_stock); nand read.e $(loadaddr) $(kernel_addr) 0xA00000; bootm $(loadadr)
to_stock=setenv mainlineLinux no; setenv bootcmd \'run bootcmd_stock\'; saveenv; reset
to_linux=setenv mainlineLinux yes; setenv bootcmd \'run bootcmd_linux\'; saveenv; reset
mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2)=root=LABEL=rootfs loglevel=8
bootargs_linux=console=ttyS0,115200 mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=LABEL=rootfs loglevel=8
bootcmd='run bootcmd_linux'
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=yes
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
disaMvPnp=no
enaAutoRecovery=yes
kernel_addr=0xc80000
pcieTune=no
pcieTune1=no
bootargs=console=ttyS0,115200 mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=LABEL=rootfs loglevel=8

I've searched a lot in this forum and google, desperately tried some suggestions, but as stated at the begin of this thread, no luck for me.