Rescue system not working after upgrading kernel (2 replies)

Quote

U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:23:43 -0700)
Pogo E02
gcc (Debian 4.9.2-10) 4.9.2
GNU ld (GNU Binutils for Debian) 2.25
Hit any key to stop autoboot: 0
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
scanning usb for storage devices...
Use USB retry period from the environment: 15 second(s)
1 Storage Device(s) found
Unknown command 'ide' - try 'help'
Unknown command 'mmc' - try 'help'

Partition Map for USB device 0 -- Partition Type: DOS

Part Start Sector Num Sectors UUID Type
1 2048 20971520 000d7189-01 83 Boot
2 20973568 1932550144 000d7189-02 07
loading envs from usb 0 ...
** File not found /boot/uEnv.txt **
Unknown command 'ide' - try 'help'
Unknown command 'mmc' - try 'help'
running scan_disk ...
Scan device usb
device usb 0:1
1 bytes read in 140 ms (0 Bytes/s)
Found bootable drive on usb 0
3260992 bytes read in 274 ms (11.3 MiB/s)
7726417 bytes read in 368 ms (20 MiB/s)
10466 bytes read in 735 ms (13.7 KiB/s)
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-4.9.0-kirkwood-tld-1
Created: 2017-01-14 14:19:36 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3260928 Bytes = 3.1 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-4.9.0-kirkwood-tld-1
Created: 2017-01-14 14:19:41 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 7726353 Bytes = 7.4 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 01c00000
Booting using the fdt blob at 0x1c00000


Starting kernel ...

Quote

U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:23:43 -0700)
Pogo E02
gcc (Debian 4.9.2-10) 4.9.2
GNU ld (GNU Binutils for Debian) 2.25
Hit any key to stop autoboot: 0
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Unknown command 'ide' - try 'help'
Unknown command 'mmc' - try 'help'

no USB devices available
Unknown command 'ide' - try 'help'
Unknown command 'mmc' - try 'help'
running scan_disk ...
Scan device usb
device usb 0:1
** Bad device usb 0 **
device usb 1:1
** Bad device usb 1 **
device usb 2:1
** Bad device usb 2 **
device usb 3:1
** Bad device usb 3 **
Scan device ide
Unknown command 'ide' - try 'help'
device ide 0:1
** Bad device ide 0 **
device ide 1:1
** Bad device ide 1 **
device ide 2:1
** Bad device ide 2 **
device ide 3:1
** Bad device ide 3 **
Scan device mmc
Unknown command 'mmc' - try 'help'
device mmc 0:1
** Bad device mmc 0 **
device mmc 1:1
** Bad device mmc 1 **
device mmc 2:1
** Bad device mmc 2 **
device mmc 3:1
** Bad device mmc 3 **
** Bad device usb 0 **
** Bad device usb 0 **
** Bad device usb 0 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!

Quote

PogoE02> printenv
printenv
arcNumber=3542
bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec
bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $loa
d_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi
bootdelay=10
bootdev=usb
device=0:1
devices=usb ide mmc
disks=0 1 2 3
dtb_file=/boot/dts/kirkwood-pogo_e02.dtb
ethact=egiga0
ethaddr=XX:XX:XX:XX:XX:XX //nic adress is ok
if_netconsole=ping $serverip
init_ide=ide reset
init_mmc=mmc rescan
init_usb=usb start
ipaddr=192.168.1.100
led_error=orange blinking
led_exit=green off
led_init=green blinking
load_dtb=ext2load usb 0:1 0x1c00000 /boot/dts/kirkwood-pogo_e02.dtb
load_dtb_addr=0x1c00000
load_initrd=ext2load usb 0:1 0x1100000 /boot/uInitrd
load_initrd_addr=0x1100000
load_uimage=ext2load usb 0:1 0x800000 /boot/uImage
load_uimage_addr=0x800000
machid=dd6
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
ncip=192.168.1.2
partition=nand0,2
preboot=run if_netconsole start_netconsole
scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev i
n $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo devi
ce $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv dev
ice $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done
scan_ide=ide reset
scan_mmc=mmc rescan
scan_usb=usb start
serverip=192.168.1.2
set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=nc
stdin=nc
stdout=nc
uenv_addr=0x810000
uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize
uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devt
ype; done;
uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done;
uenv_loaded=0
uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi
uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi
usb_boot=run load_dtb; run load_uimage; if run load_initrd; then bootm 0x800000 0x1100000 0x1c00000; else bootm 0x800000 - 0x1c00000; fi
usb_ready_retry=15

Environment size: 3171/131068 bytes
PogoE02>