I use tarball from this thread http://forum.doozan.com/read.php?2,12096 by bodhi to create a wheezy stick. It booted up fine. However, when I try to install anything by apt-get, the unpacking get extremely slow. I don't know if anything is wrong with dpkg or apt-get.
My fw_printenv
My fw_printenv
arcNumber=2097 baudrate=115200 bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset bootdelay=10 console=ttyS0,115200 ethact=egiga0 ethaddr= force_rescue=0 force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi if_netconsole=ping $serverip ipaddr=192.168.1.41 led_error=orange blinking led_exit=green off led_init=green blinking mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) ncip=192.168.1.130 partition=nand0,2 pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi preboot=run if_netconsole start_netconsole rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi rescue_installed=1 rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params serverip=192.168.1.130 start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=nc stdin=nc stdout=nc ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi ubifs_mtd=3 ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot usb_device=0:1 usb_init=run usb_scan usb_root=/dev/sda1 usb_rootdelay=10 usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done usb_scan_1=usb=0:1 dev=sda1 usb_scan_2=usb=1:1 dev=sdb1 usb_scan_3=usb=2:1 dev=sdc1 usb_scan_4=usb=3:1 dev=sdd1 usb_scan_list=1 2 3 4 usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params usb_rootfstype=ext2fdisk -l
Disk /dev/sda: 7876 MB, 7876902912 bytes 243 heads, 62 sectors/track, 1021 cylinders, total 15384576 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x8de7428d Device Boot Start End Blocks Id System /dev/sda1 * 2048 4194303 2096128 83 Linux /dev/sda2 4194304 13275135 4540416 83 Linux /dev/sda3 13275136 15372287 1048576 82 Linux swap / Solaris