Hello, all
First time poster. I "inherited" a broken E02 and want to see if I can salvage it. Not sure what happened previously but could never ssh into it. Just received USB TTL converter and soundblaster cable, hooked it up and at least it's talking to me. Have been reading LOTS here, learning much -- but still not understanding much of what Pogo's telling me. Here's what I got:
______________________
U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02
SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported
** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 91 MiB
UBI: number of good PEBs: 726
UBI: number of bad PEBs: 2
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 715
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: ........ read_nand_cached: error reading nand off 0xffec00 s ize 8192 bytes
read_nand_cached: error reading nand off 0x1000c00 size 8192 bytes
read_nand_cached: error reading nand off 0x123fe00 size 8192 bytes
read_nand_cached: error reading nand off 0x123fc00 size 8192 bytes
read_nand_cached: error reading nand off 0x1241c00 size 8192 bytes d one.
read_nand_cached: error reading nand off 0x123fa00 size 8192 bytes
off = 0x123f768 magic 0x1985 type 0xe002 node.totlen = 1633
### JFFS2 load complete: 524288 bytes loaded to 0x800000
## Starting application at 0x00800200 ...
U-Boot 1.1.4 (Sep 28 2009 - 11:55:23) Cloud Engines v2.0 (3.4.16)
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60
Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Flash: 0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:128 MB
CPU : Marvell Feroceon (Rev 1)
CLOUD ENGINES BOARD: PPV2
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x100000, size 0x200000
Reading data from 0x2ff800 -- 100% complete.
2097152 bytes read: OK
## Booting image at 00800000 ...
Image Name: Linux-2.6.22.18
Created: 2010-10-19 23:05:02 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1979140 Bytes = 1.9 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux............................................................................................................................ done, booting the kernel.
[ 0.000000] Linux version 2.6.22.18 (bdietrich@buildman) (gcc version 4.2.1) #81 Tue Oct 19 16:05:00 PDT 2010
[ 0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177
[ 0.000000] Machine: Feroceon-KW
[ 0.000000] Using UBoot passing parameters structure
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] CPU0: D VIVT write-back cache
[ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
[ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
[ 0.000000] Built 1 zonelists. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro
[ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.010000] Memory: 256MB 0MB 0MB 0MB = 256MB total
[ 0.010000] Memory: 255872KB available (3592K code, 253K data, 124K init)
[ 0.250000] Mount-cache hash table entries: 512
[ 0.250000] CPU: Testing write buffer coherency: ok
[ 0.250000] NET: Registered protocol family 16
[ 0.250000]
[ 0.250000] CPU Interface
[ 0.250000] -------------
[ 0.250000] SDRAM_CS0 ....base 00000000, size 256MB
[ 0.250000] SDRAM_CS1 ....disable
[ 0.250000] SDRAM_CS2 ....disable
[ 0.250000] SDRAM_CS3 ....disable
[ 0.250000] PEX0_MEM ....base e8000000, size 128MB
[ 0.250000] PEX0_IO ....base f2000000, size 1MB
[ 0.250000] INTER_REGS ....base f1000000, size 1MB
[ 0.250000] NFLASH_CS ....base fa000000, size 2MB
[ 0.250000] SPI_CS ....base f4000000, size 16MB
[ 0.250000] BOOT_ROM_CS ....no such
[ 0.250000] DEV_BOOTCS ....no such
[ 0.250000] CRYPT_ENG ....base f0000000, size 2MB
[ 0.250000]
[ 0.250000] Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21_with_rx_desc_tuned)-- SHEEVA PLUG Soc: 88F6281 A0 LE
[ 0.250000]
[ 0.250000] Detected Tclk 200000000 and SysClk 400000000
[ 0.250000] MV Buttons Device Load
[ 0.250000] Marvell USB EHCI Host controller #0: c0652600
[ 0.750000] PEX0 interface detected no Link.
[ 0.750000] PCI: bus0: Fast back to back transfers enabled
[ 0.750000] SCSI subsystem initialized
[ 0.750000] usbcore: registered new interface driver usbfs
[ 0.750000] usbcore: registered new interface driver hub
[ 0.750000] usbcore: registered new device driver usb
[ 0.750000] NET: Registered protocol family 2
[ 0.760000] Time: kw_clocksource clocksource has been installed.
[ 0.850000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.850000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.850000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.850000] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.850000] TCP reno registered
[ 0.880000] RTC has been updated!!!
[ 0.880000] RTC registered
[ 0.880000] Use the XOR engines (acceleration) for enhancing the following functions:
[ 0.880000] o RAID 5 Xor calculation
[ 0.880000] o kernel memcpy
[ 0.880000] o kenrel memzero
[ 0.880000] Number of XOR engines to use: 4
[ 0.880000] cesadev_init(c00117b0)
[ 0.880000] mvCesaInit: sessions=640, queue=64, pSram=f0000000
[ 0.880000] MV Buttons Driver Load
[ 0.880000] squashfs: version 3.3 (2007/10/31) Phillip Lougher
[ 0.880000] squashfs: LZMA suppport for slax.org by jro
[ 0.880000] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.880000] io scheduler noop registered
[ 0.880000] io scheduler anticipatory registered (default)
[ 0.900000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
[ 0.900000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 0.910000] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
[ 0.920000] Loading Marvell Ethernet Driver:
[ 0.920000] o Cached descriptors in DRAM
[ 0.920000] o DRAM SW cache-coherency
[ 0.930000] o Single RX Queue support - ETH_DEF_RXQ=0
[ 0.930000] o Single TX Queue support - ETH_DEF_TXQ=0
[ 0.940000] o TCP segmentation offload enabled
[ 0.940000] o Receive checksum offload enabled
[ 0.950000] o Transmit checksum offload enabled
[ 0.950000] o Network Fast Processing (Routing) supported
[ 0.960000] o Driver ERROR statistics enabled
[ 0.960000] o Driver INFO statistics enabled
[ 0.970000] o Proc tool API enabled
[ 0.970000] o Rx descripors: q0=128
[ 0.970000] o Tx descripors: q0=532
[ 0.980000] o Loading network interface(s):
[ 0.990000] o eth0, ifindex = 1, GbE port = 0
[ 0.990000] o eth1, ifindex = 2, GbE port = 1
[ 1.000000]
[ 1.000000] mvFpRuleDb (cfdf6000): 2048 entries, 8192 bytes
[ 1.000000] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
[ 1.010000] Copyright (c) 1999-2006 Intel Corporation.
[ 1.020000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
[ 1.020000] e100: Copyright(c) 1999-2006 Intel Corporation
[ 1.030000]
[ 1.030000] Warning Sata is Powered Off
[ 1.030000] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
[ 1.040000] NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
[ 1.050000] Scanning device for bad blocks
[ 1.060000] Bad eraseblock 128 at 0x01000000
[ 1.070000] Bad eraseblock 146 at 0x01240000
[ 1.100000] Bad eraseblock 830 at 0x067c0000
[ 1.110000] Bad eraseblock 930 at 0x07440000
[ 1.120000] Using static partition definition
[ 1.120000] Creating 4 MTD partitions on "nand_mtd":
[ 1.130000] 0x00000000-0x00100000 : "u-boot"
[ 1.130000] 0x00100000-0x00500000 : "uImage"
[ 1.140000] 0x00500000-0x02500000 : "root"
[ 1.140000] 0x02500000-0x08000000 : "data"
[ 1.150000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
[ 1.150000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
[ 1.190000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
[ 1.210000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 1.210000] usb usb1: configuration #1 chosen from 1 choice
[ 1.220000] hub 1-0:1.0: USB hub found
[ 1.220000] hub 1-0:1.0: 1 port detected
[ 1.340000] USB Universal Host Controller Interface driver v3.0
[ 1.340000] usbcore: registered new interface driver usblp
[ 1.350000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[ 1.350000] Initializing USB Mass Storage driver...
[ 1.360000] usbcore: registered new interface driver usb-storage
[ 1.370000] USB Mass Storage support registered.
[ 1.370000] mice: PS/2 mouse device common for all mice
[ 1.380000] i2c /dev entries driver
[ 1.380000] Linux telephony interface: v1.00
[ 1.380000] md: linear personality registered for level -1
[ 1.390000] md: raid0 personality registered for level 0
[ 1.390000] md: raid1 personality registered for level 1
[ 1.570000] raid6: int32x1 97 MB/s
[ 1.740000] raid6: int32x2 114 MB/s
[ 1.910000] raid6: int32x4 122 MB/s
[ 2.080000] raid6: int32x8 110 MB/s
[ 2.080000] raid6: using algorithm int32x4 (122 MB/s)
[ 2.080000] md: raid6 personality registered for level 6
[ 2.090000] md: raid5 personality registered for level 5
[ 2.090000] md: raid4 personality registered for level 4
[ 2.100000] raid5: measuring checksumming speed
[ 2.150000] arm4regs : 1071.600 MB/sec
[ 2.200000] 8regs : 754.800 MB/sec
[ 2.250000] 32regs : 900.000 MB/sec
[ 2.250000] raid5: using function: arm4regs (1071.600 MB/sec)
[ 2.260000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
[ 2.260000] dm_crypt using the OCF package.
[ 2.270000] sdhci: Secure Digital Host Controller Interface driver
[ 2.270000] sdhci: Copyright(c) Pierre Ossman
[ 2.280000] usbcore: registered new interface driver usbhid
[ 2.280000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 2.290000] TCP cubic registered
[ 2.290000] NET: Registered protocol family 1
[ 2.300000] NET: Registered protocol family 17
[ 2.300000] md: Autodetecting RAID arrays.
[ 2.310000] md: autorun ...
[ 2.310000] md: ... autorun DONE.
[ 3.220000] jffs2_scan_dirent_node(): Name CRC failed on node at 0x0038e7d8: Read 0x84355ba0, calculated 0xf01b4ca3
[ 3.800000] Empty flash at 0x009ac208 ends at 0x009ac800
[ 8.070000] VFS: Mounted root (jffs2 filesystem) readonly.
[ 8.080000] Freeing init memory: 124K
init started: BusyBox v1.7.0 (2008-02-26 19:25:17 IST)
starting pid 262, tty '': '/etc/init.d/rcS'
[ 10.290000] eth0: started
udhcpc (v1.7.0) started
HWADDR 00 0x25 0x31 0x00 0x8b 0x30
PIP0 139
PIP1 48
cat: can't open '/etc/resolv.conf': No such file or directory
route: SIOCDELRT: No such process
grep: /etc/resolv.conf: No such file or directory
Sending discover...
Sending discover...
Sending discover...
HWADDR 00 0x25 0x31 0x00 0x8b 0x30
PIP0 139
PIP1 48
No lease, forking to background
Loading fs modules: [ 20.360000] fuse init (API version 7.8)
Success
[ 20.680000] ufsd: module license 'Commercial product' taints kernel.
[ 20.700000] ufsd: driver (8.6, Jun 5 2013 10:00:32, LBD=ON, ioctl) loaded at bf040000
[ 20.700000] NTFS support included
[ 20.700000] Hfs+/HfsX support included
[ 20.700000] For 'CloudEngines_PogoPlug_2011-08-03'
Loading rt3070sta.ko: [ 21.160000] rtusb init --->
[ 21.170000] usbcore: registered new interface driver rt2870
Success
Loading tun.ko: [ 21.190000] tun: Universal TUN/TAP device driver, 1.6
[ 21.190000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Success
Loading xce.ko: [ 21.230000] Cloud Engines XCE Init [Version: 2.0.5.10]
[ 21.230000] XCE: CPU MEMORY MAP:
[ 21.240000] XCE: -- 0x00001000 - 0xbeffffff (3055 MB) User Space Mappings
[ 21.240000] XCE: -- 0xbf000000 - 0xbfffffff ( 16 MB) Kernel module space
[ 21.250000] XCE: -- 0xc0000000 - 0xcfffffff ( 256 MB) Kernel direct-mapped ram
[ 21.260000] XCE: -- 0xd0800000 - 0xe7ffffff ( 376 MB) Kernel vmalloc space
[ 21.270000] XCE: -- 0xe8000000 - 0xfeffffff ( 367 MB) Kernel platform space
[ 21.270000] XCE: CPU FEATURES:
[ 21.280000] XCE: -- I Cache: enabled
[ 21.280000] XCE: -- D Cache: enabled
[ 21.280000] XCE: -- Branch Predict: enabled
[ 21.290000] XCE: -- MMU: enabled
[ 21.290000] XCE: -- Alignment Abort: enabled
[ 21.300000] XCE: -- ICache Prefetch: enabled
[ 21.300000] XCE: -- DCache Prefetch: enabled
[ 21.310000] XCE: -- L2 Cache: enabled
[ 21.310000] XCE: -- L2 Prefetch: disabled
[ 21.320000] XCE: -- L2 Writethrough: disabled
[ 21.320000] XCE: -- Write Allocate: disabled
[ 21.330000] XCE: -- Streaming: disabled
[ 21.330000] XCE: BLPARAMS: reading 2048 bytes @ a0000
[ 21.340000] XCE: Loaded Property Size: 2048
[ 21.340000] XCE: - 'cesvcid' -> '7LGC4DPJUA5ZVXGCMMN6APYLAA'
[ 21.350000] XCE: - 'ceboardver' -> 'PPV2'
[ 21.350000] XCE: Current GPIO State:
[ 21.350000] XCE: GPIO L OUT: 0xeff00000
[ 21.360000] XCE: GPIO L OE: 0xefffffff
[ 21.360000] XCE: GPIO L BLINK: 0x00000000
[ 21.370000] XCE: GPIO L POL: 0x00000000
[ 21.370000] XCE: GPIO L IN: 0x00000080
[ 21.380000] XCE: GPIO H OUT: 0xffffffff
[ 21.380000] XCE: GPIO H OE: 0xfffc3fff
[ 21.380000] XCE: GPIO H BLINK: 0x00008000
[ 21.390000] XCE: GPIO H POL: 0x00000000
[ 21.390000] XCE: GPIO H IN: 0x00034000
[ 21.400000] XCE: Kernel thread starting PID: 386
Success
Starting hbplug: Success
starting pid 388, tty '': '/bin/sh'
-sh-4.3# [ 23.300000] XCE: BLPARAMS: reading 2048 bytes @ a0000
[ 23.310000] XCE: BLPARAMS: reading 2048 bytes @ a0800
[ 23.310000] XCE: BLPARAMS: reading 2048 bytes @ a1000
[ 23.320000] XCE: BLPARAMS: reading 2048 bytes @ a1800
[ 28.680000] XCE: XCE: LED -> DISCONNECTED
_________________
So can someone point me in the right direction. Truthfully, it's gonna be more like a lot of hand-holding. Any takers?
Thanks
First time poster. I "inherited" a broken E02 and want to see if I can salvage it. Not sure what happened previously but could never ssh into it. Just received USB TTL converter and soundblaster cable, hooked it up and at least it's talking to me. Have been reading LOTS here, learning much -- but still not understanding much of what Pogo's telling me. Here's what I got:
______________________
U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02
SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported
** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 91 MiB
UBI: number of good PEBs: 726
UBI: number of bad PEBs: 2
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 715
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: ........ read_nand_cached: error reading nand off 0xffec00 s ize 8192 bytes
read_nand_cached: error reading nand off 0x1000c00 size 8192 bytes
read_nand_cached: error reading nand off 0x123fe00 size 8192 bytes
read_nand_cached: error reading nand off 0x123fc00 size 8192 bytes
read_nand_cached: error reading nand off 0x1241c00 size 8192 bytes d one.
read_nand_cached: error reading nand off 0x123fa00 size 8192 bytes
off = 0x123f768 magic 0x1985 type 0xe002 node.totlen = 1633
### JFFS2 load complete: 524288 bytes loaded to 0x800000
## Starting application at 0x00800200 ...
U-Boot 1.1.4 (Sep 28 2009 - 11:55:23) Cloud Engines v2.0 (3.4.16)
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60
Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Flash: 0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:128 MB
CPU : Marvell Feroceon (Rev 1)
CLOUD ENGINES BOARD: PPV2
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x100000, size 0x200000
Reading data from 0x2ff800 -- 100% complete.
2097152 bytes read: OK
## Booting image at 00800000 ...
Image Name: Linux-2.6.22.18
Created: 2010-10-19 23:05:02 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1979140 Bytes = 1.9 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux............................................................................................................................ done, booting the kernel.
[ 0.000000] Linux version 2.6.22.18 (bdietrich@buildman) (gcc version 4.2.1) #81 Tue Oct 19 16:05:00 PDT 2010
[ 0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177
[ 0.000000] Machine: Feroceon-KW
[ 0.000000] Using UBoot passing parameters structure
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] CPU0: D VIVT write-back cache
[ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
[ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
[ 0.000000] Built 1 zonelists. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro
[ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.010000] Memory: 256MB 0MB 0MB 0MB = 256MB total
[ 0.010000] Memory: 255872KB available (3592K code, 253K data, 124K init)
[ 0.250000] Mount-cache hash table entries: 512
[ 0.250000] CPU: Testing write buffer coherency: ok
[ 0.250000] NET: Registered protocol family 16
[ 0.250000]
[ 0.250000] CPU Interface
[ 0.250000] -------------
[ 0.250000] SDRAM_CS0 ....base 00000000, size 256MB
[ 0.250000] SDRAM_CS1 ....disable
[ 0.250000] SDRAM_CS2 ....disable
[ 0.250000] SDRAM_CS3 ....disable
[ 0.250000] PEX0_MEM ....base e8000000, size 128MB
[ 0.250000] PEX0_IO ....base f2000000, size 1MB
[ 0.250000] INTER_REGS ....base f1000000, size 1MB
[ 0.250000] NFLASH_CS ....base fa000000, size 2MB
[ 0.250000] SPI_CS ....base f4000000, size 16MB
[ 0.250000] BOOT_ROM_CS ....no such
[ 0.250000] DEV_BOOTCS ....no such
[ 0.250000] CRYPT_ENG ....base f0000000, size 2MB
[ 0.250000]
[ 0.250000] Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21_with_rx_desc_tuned)-- SHEEVA PLUG Soc: 88F6281 A0 LE
[ 0.250000]
[ 0.250000] Detected Tclk 200000000 and SysClk 400000000
[ 0.250000] MV Buttons Device Load
[ 0.250000] Marvell USB EHCI Host controller #0: c0652600
[ 0.750000] PEX0 interface detected no Link.
[ 0.750000] PCI: bus0: Fast back to back transfers enabled
[ 0.750000] SCSI subsystem initialized
[ 0.750000] usbcore: registered new interface driver usbfs
[ 0.750000] usbcore: registered new interface driver hub
[ 0.750000] usbcore: registered new device driver usb
[ 0.750000] NET: Registered protocol family 2
[ 0.760000] Time: kw_clocksource clocksource has been installed.
[ 0.850000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.850000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.850000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.850000] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.850000] TCP reno registered
[ 0.880000] RTC has been updated!!!
[ 0.880000] RTC registered
[ 0.880000] Use the XOR engines (acceleration) for enhancing the following functions:
[ 0.880000] o RAID 5 Xor calculation
[ 0.880000] o kernel memcpy
[ 0.880000] o kenrel memzero
[ 0.880000] Number of XOR engines to use: 4
[ 0.880000] cesadev_init(c00117b0)
[ 0.880000] mvCesaInit: sessions=640, queue=64, pSram=f0000000
[ 0.880000] MV Buttons Driver Load
[ 0.880000] squashfs: version 3.3 (2007/10/31) Phillip Lougher
[ 0.880000] squashfs: LZMA suppport for slax.org by jro
[ 0.880000] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.880000] io scheduler noop registered
[ 0.880000] io scheduler anticipatory registered (default)
[ 0.900000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
[ 0.900000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 0.910000] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
[ 0.920000] Loading Marvell Ethernet Driver:
[ 0.920000] o Cached descriptors in DRAM
[ 0.920000] o DRAM SW cache-coherency
[ 0.930000] o Single RX Queue support - ETH_DEF_RXQ=0
[ 0.930000] o Single TX Queue support - ETH_DEF_TXQ=0
[ 0.940000] o TCP segmentation offload enabled
[ 0.940000] o Receive checksum offload enabled
[ 0.950000] o Transmit checksum offload enabled
[ 0.950000] o Network Fast Processing (Routing) supported
[ 0.960000] o Driver ERROR statistics enabled
[ 0.960000] o Driver INFO statistics enabled
[ 0.970000] o Proc tool API enabled
[ 0.970000] o Rx descripors: q0=128
[ 0.970000] o Tx descripors: q0=532
[ 0.980000] o Loading network interface(s):
[ 0.990000] o eth0, ifindex = 1, GbE port = 0
[ 0.990000] o eth1, ifindex = 2, GbE port = 1
[ 1.000000]
[ 1.000000] mvFpRuleDb (cfdf6000): 2048 entries, 8192 bytes
[ 1.000000] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
[ 1.010000] Copyright (c) 1999-2006 Intel Corporation.
[ 1.020000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
[ 1.020000] e100: Copyright(c) 1999-2006 Intel Corporation
[ 1.030000]
[ 1.030000] Warning Sata is Powered Off
[ 1.030000] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
[ 1.040000] NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
[ 1.050000] Scanning device for bad blocks
[ 1.060000] Bad eraseblock 128 at 0x01000000
[ 1.070000] Bad eraseblock 146 at 0x01240000
[ 1.100000] Bad eraseblock 830 at 0x067c0000
[ 1.110000] Bad eraseblock 930 at 0x07440000
[ 1.120000] Using static partition definition
[ 1.120000] Creating 4 MTD partitions on "nand_mtd":
[ 1.130000] 0x00000000-0x00100000 : "u-boot"
[ 1.130000] 0x00100000-0x00500000 : "uImage"
[ 1.140000] 0x00500000-0x02500000 : "root"
[ 1.140000] 0x02500000-0x08000000 : "data"
[ 1.150000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
[ 1.150000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
[ 1.190000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
[ 1.210000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 1.210000] usb usb1: configuration #1 chosen from 1 choice
[ 1.220000] hub 1-0:1.0: USB hub found
[ 1.220000] hub 1-0:1.0: 1 port detected
[ 1.340000] USB Universal Host Controller Interface driver v3.0
[ 1.340000] usbcore: registered new interface driver usblp
[ 1.350000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[ 1.350000] Initializing USB Mass Storage driver...
[ 1.360000] usbcore: registered new interface driver usb-storage
[ 1.370000] USB Mass Storage support registered.
[ 1.370000] mice: PS/2 mouse device common for all mice
[ 1.380000] i2c /dev entries driver
[ 1.380000] Linux telephony interface: v1.00
[ 1.380000] md: linear personality registered for level -1
[ 1.390000] md: raid0 personality registered for level 0
[ 1.390000] md: raid1 personality registered for level 1
[ 1.570000] raid6: int32x1 97 MB/s
[ 1.740000] raid6: int32x2 114 MB/s
[ 1.910000] raid6: int32x4 122 MB/s
[ 2.080000] raid6: int32x8 110 MB/s
[ 2.080000] raid6: using algorithm int32x4 (122 MB/s)
[ 2.080000] md: raid6 personality registered for level 6
[ 2.090000] md: raid5 personality registered for level 5
[ 2.090000] md: raid4 personality registered for level 4
[ 2.100000] raid5: measuring checksumming speed
[ 2.150000] arm4regs : 1071.600 MB/sec
[ 2.200000] 8regs : 754.800 MB/sec
[ 2.250000] 32regs : 900.000 MB/sec
[ 2.250000] raid5: using function: arm4regs (1071.600 MB/sec)
[ 2.260000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
[ 2.260000] dm_crypt using the OCF package.
[ 2.270000] sdhci: Secure Digital Host Controller Interface driver
[ 2.270000] sdhci: Copyright(c) Pierre Ossman
[ 2.280000] usbcore: registered new interface driver usbhid
[ 2.280000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 2.290000] TCP cubic registered
[ 2.290000] NET: Registered protocol family 1
[ 2.300000] NET: Registered protocol family 17
[ 2.300000] md: Autodetecting RAID arrays.
[ 2.310000] md: autorun ...
[ 2.310000] md: ... autorun DONE.
[ 3.220000] jffs2_scan_dirent_node(): Name CRC failed on node at 0x0038e7d8: Read 0x84355ba0, calculated 0xf01b4ca3
[ 3.800000] Empty flash at 0x009ac208 ends at 0x009ac800
[ 8.070000] VFS: Mounted root (jffs2 filesystem) readonly.
[ 8.080000] Freeing init memory: 124K
init started: BusyBox v1.7.0 (2008-02-26 19:25:17 IST)
starting pid 262, tty '': '/etc/init.d/rcS'
[ 10.290000] eth0: started
udhcpc (v1.7.0) started
HWADDR 00 0x25 0x31 0x00 0x8b 0x30
PIP0 139
PIP1 48
cat: can't open '/etc/resolv.conf': No such file or directory
route: SIOCDELRT: No such process
grep: /etc/resolv.conf: No such file or directory
Sending discover...
Sending discover...
Sending discover...
HWADDR 00 0x25 0x31 0x00 0x8b 0x30
PIP0 139
PIP1 48
No lease, forking to background
Loading fs modules: [ 20.360000] fuse init (API version 7.8)
Success
[ 20.680000] ufsd: module license 'Commercial product' taints kernel.
[ 20.700000] ufsd: driver (8.6, Jun 5 2013 10:00:32, LBD=ON, ioctl) loaded at bf040000
[ 20.700000] NTFS support included
[ 20.700000] Hfs+/HfsX support included
[ 20.700000] For 'CloudEngines_PogoPlug_2011-08-03'
Loading rt3070sta.ko: [ 21.160000] rtusb init --->
[ 21.170000] usbcore: registered new interface driver rt2870
Success
Loading tun.ko: [ 21.190000] tun: Universal TUN/TAP device driver, 1.6
[ 21.190000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Success
Loading xce.ko: [ 21.230000] Cloud Engines XCE Init [Version: 2.0.5.10]
[ 21.230000] XCE: CPU MEMORY MAP:
[ 21.240000] XCE: -- 0x00001000 - 0xbeffffff (3055 MB) User Space Mappings
[ 21.240000] XCE: -- 0xbf000000 - 0xbfffffff ( 16 MB) Kernel module space
[ 21.250000] XCE: -- 0xc0000000 - 0xcfffffff ( 256 MB) Kernel direct-mapped ram
[ 21.260000] XCE: -- 0xd0800000 - 0xe7ffffff ( 376 MB) Kernel vmalloc space
[ 21.270000] XCE: -- 0xe8000000 - 0xfeffffff ( 367 MB) Kernel platform space
[ 21.270000] XCE: CPU FEATURES:
[ 21.280000] XCE: -- I Cache: enabled
[ 21.280000] XCE: -- D Cache: enabled
[ 21.280000] XCE: -- Branch Predict: enabled
[ 21.290000] XCE: -- MMU: enabled
[ 21.290000] XCE: -- Alignment Abort: enabled
[ 21.300000] XCE: -- ICache Prefetch: enabled
[ 21.300000] XCE: -- DCache Prefetch: enabled
[ 21.310000] XCE: -- L2 Cache: enabled
[ 21.310000] XCE: -- L2 Prefetch: disabled
[ 21.320000] XCE: -- L2 Writethrough: disabled
[ 21.320000] XCE: -- Write Allocate: disabled
[ 21.330000] XCE: -- Streaming: disabled
[ 21.330000] XCE: BLPARAMS: reading 2048 bytes @ a0000
[ 21.340000] XCE: Loaded Property Size: 2048
[ 21.340000] XCE: - 'cesvcid' -> '7LGC4DPJUA5ZVXGCMMN6APYLAA'
[ 21.350000] XCE: - 'ceboardver' -> 'PPV2'
[ 21.350000] XCE: Current GPIO State:
[ 21.350000] XCE: GPIO L OUT: 0xeff00000
[ 21.360000] XCE: GPIO L OE: 0xefffffff
[ 21.360000] XCE: GPIO L BLINK: 0x00000000
[ 21.370000] XCE: GPIO L POL: 0x00000000
[ 21.370000] XCE: GPIO L IN: 0x00000080
[ 21.380000] XCE: GPIO H OUT: 0xffffffff
[ 21.380000] XCE: GPIO H OE: 0xfffc3fff
[ 21.380000] XCE: GPIO H BLINK: 0x00008000
[ 21.390000] XCE: GPIO H POL: 0x00000000
[ 21.390000] XCE: GPIO H IN: 0x00034000
[ 21.400000] XCE: Kernel thread starting PID: 386
Success
Starting hbplug: Success
starting pid 388, tty '': '/bin/sh'
-sh-4.3# [ 23.300000] XCE: BLPARAMS: reading 2048 bytes @ a0000
[ 23.310000] XCE: BLPARAMS: reading 2048 bytes @ a0800
[ 23.310000] XCE: BLPARAMS: reading 2048 bytes @ a1000
[ 23.320000] XCE: BLPARAMS: reading 2048 bytes @ a1800
[ 28.680000] XCE: XCE: LED -> DISCONNECTED
_________________
So can someone point me in the right direction. Truthfully, it's gonna be more like a lot of hand-holding. Any takers?
Thanks