Lenovo ix2-dl won't boot with kernel newer than 4.10.9 (3 replies)

Hi All,

My ix2-dl has been operating fine on the 4.4.0 kernel and rootfs for a while. Today I took it offline to update the kernel and move the rootfs onto a sata drive and have found it doesn't boot beyond 'Starting Kernel' on kernel / initrd past 4.10.9.

This is still with root on the usb, I've not set up the sata boot yet.

Here is the boot log and printenv;

log (4.12 boot attempt);

** ix2-nand ** ** uboot_ver:0.0.8 **

 ** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:19:29) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CFB00

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000   size 256MB
DRAM Total size 256MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:1024 MB
Found ADT7473, program PWM1 ... OK
Flash:  0 kB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST2000DM001-1CH164                       Firm: CC26     Ser#:             Z2F0PEJZ
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
[0 1 0]: Enable DMA mode (6)
  Device 1 @ 0 1:
Model: ST1000DM003-9YN162                       Firm: CC9D     Ser#:             Z1D0F6TF
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)


CPU : Marvell Feroceon (Rev 1)
Found kernel at 0x100000
Found initrd at 0x400000

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
(Re)start USB...
USB:   scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
....
..................................................................................................................

..................................................................................................................

..................................................................................................................

...........................

3834683 bytes read
....
..................................................................................................................

............................................
.
..................................................................................................................

..................................................................................................................

...................
..................................................................................................................

..................................................................................................................

..................................................................................................................

...................................................

8268888 bytes read
## Booting image at 00800000 ...
   Image Name:   Linux-4.12.1-kirkwood-tld-1
   Created:      2018-10-20   0:48:49 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3834619 Bytes =  3.7 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01100000 ...
   Image Name:   initramfs-4.12.1-kirkwood-tld-1
   Created:      2018-10-20   0:49:12 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    8268824 Bytes =  7.9 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

printenv

Hit any key to stop autoboot:  0
Marvell>> printenv
baudrate=115200
loads_echo=0
rootpath=/srv/ubuntu
netmask=255.255.255.0
run_diag=yes
MALLOC_len=1
ethprime=egiga0
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):

$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
lcd0_enable=0
lcd0_params=640x480-16@60
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
nandEcc=1bit
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
image_multi=yes
ethact=egiga0
kernel_size=0x300000
loadzimage=nand read.e 0x40000 $(kernel_start) $(kernel_size)
loadinitrd=nand read.e 0x900000 $(initrd_start) $(initrd_size)
console=console=ttyS0,115200
bootargs_root=root=/dev/ram0
initrdimage=mfginitrd
ipaddr=192.168.1.2
mfgmodel=ix2
preroot_ver=0.0.2
uboot_ver=0.0.8
serial_number=5563Y01011G33400015J0H1
ethaddr=00:D0:B8:15:62:7F
serialNo=V7AD360054
modelname=70A69003AP
fw_ver=4.0.4.14600d
serialno=1,01qImmfct4zUs3yki67JMy2LfVN603V+W1CY2gpTd1BPOPOB+KEBaLjxL2hhBGH2Rz,V7AD360054,
runintime=10800
ftpserver=192.168.43.4
testfile=100M
mfgtest_state=system_tested_ok
pre_path=IX2/1.0.8/download_runin.sh
pre_path_conf=IX2/1.0.8/download_runin.conf
pre_serverip=192.168.32.4
pre_user=ixxrunin
pre_passwd=123
pre_dirzi=IX2/1.0.8
serverip=192.168.32.4
initrd_size=0x400000
arcNumber=1682
load_uImage=ext2load usb 0:1 0x800000 /uImage
bootcmd=run=loadzimage
mk_mtdparts=setenv=mtdparts mtdparts=nand_mtd:0x80000@0(uboot),0x20000@0xa0000(env),0x20000@0xc0000(env2),

$(kernel_size)@$(kernel_start)(uImage),$(initrd_size)@$(initrd_start)(initrd),0x3f800000@0x800000(boot),1024m@0x0

(flash)
rootdelay=10
usb_root=LABEL=rootfs
bootcmd=run usb_boot
usb_boot=usb start; run load_uimage; run load_initrd; bootm 0x800000 0x1100000
bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x80000@0(uboot),0x20000@0xa0000

(env),0x20000@0xc0000(env2),0x300000@0x100000(uImage),0x400000@0x400000(initrd),0x3f800000@0x800000

(boot),1024m@0x0(flash) earlyprintk=serial
rootfstype=ext3
load_initrd=ext2load usb 0:1 0x1100000 /boot/uInitrd
load_uimage=ext2load usb 0:1 0x800000 /boot/uImage
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=yes
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
kernel_start=0x100000
initrd_start=0x400000
bootdelay=3
disaMvPnp=no
enaAutoRecovery=yes
pcieTune=no
pcieTune1=no

Environment size: 2620/131067 bytes

/boot

root@bagend:/boot# ls
.
..
System.map-4.10.9-kirkwood-tld-1
System.map-4.11.3-kirkwood-tld-2
System.map-4.12.1-kirkwood-tld-1
System.map-4.4.0-kirkwood-tld-1
config-4.10.9-kirkwood-tld-1
config-4.11.3-kirkwood-tld-2
config-4.12.1-kirkwood-tld-1
config-4.4.0-kirkwood-tld-1
dts
initrd.img-4.10.9-kirkwood-tld-1
initrd.img-4.11.3-kirkwood-tld-2
initrd.img-4.12.1-kirkwood-tld-1
initrd.img-4.4.0-kirkwood-tld-1
linux-4.10.9-kirkwood-tld-1-bodhi.tar.bz2
linux-4.10.9-kirkwood-tld-1.patch
linux-4.11.3-kirkwood-tld-2-bodhi.tar.bz2
linux-4.11.3-kirkwood-tld-2.patch
linux-4.12.1-kirkwood-tld-1-bodhi.tar.bz2
linux-4.12.1-kirkwood-tld-1.patch
linux-dtb-4.10.9-kirkwood-tld-1.tar
linux-dtb-4.11.3-kirkwood-tld-2.tar
linux-dtb-4.12.1-kirkwood-tld-1.tar
linux-headers-4.10.9-kirkwood-tld-1_1.0_armel.deb
linux-headers-4.11.3-kirkwood-tld-2_2.0_armel.deb
linux-headers-4.12.1-kirkwood-tld-1_1.0_armel.deb
linux-headers-4.4.0-kirkwood-tld-1_1.0_armel.deb
linux-image-4.10.9-kirkwood-tld-1_1.0_armel.deb
linux-image-4.11.3-kirkwood-tld-2_2.0_armel.deb
linux-image-4.12.1-kirkwood-tld-1_1.0_armel.deb
uImage
uImage.4.11
uImage.4.12
uImage.4.4
uImage.orig
uImage4.10
uInitrd
uInitrd.4.11
uInitrd.4.12
uInitrd.4.4
uInitrd4.10
vmlinuz-4.10.9-kirkwood-tld-1
vmlinuz-4.11.3-kirkwood-tld-2
vmlinuz-4.12.1-kirkwood-tld-1
vmlinuz-4.4.0-kirkwood-tld-1
zImage-4.10.9-kirkwood-tld-1
zImage-4.11.3-kirkwood-tld-2
zImage-4.12.1-kirkwood-tld-1
zImage-4.4.0-kirkwood-tld-1
zImage.fdt

Anyone have an idea?

Thanks,
J