Hello, help to fix my device... [Akitio MyCloud Mini] (1 reply)

Hello, i am from korea.

I tried to install on this device.
I install a new bootloader on this device.
But I made a mistake.
This device is not backed up properly.
So the NAND drive doesn't boot at all.
Only the spl area is displayed from NAND drive.

So, I made a new attempt.
Try booting to s-ata.
Initially, it does not boot well.
After several attempts, u-boot succeeded.
However, it started to get blocked from `Uncompressing Linux ... done, booting the kernel.`.
I tried formatting and reinstalling the s-ata disk, but it didn't work at all.

See here : https://forum.doozan.com/read.php?3,42599

Is this possible only with pogoplug v3?
What should I do?

Thanks for the help.

(Sorry my English, help with translator)

Device log :

[If unplugged s-ata drive]

U-Boot SPL 2013.10-tld-4 (Sep 07 2014 - 14:10:12)
  Boot device: NAND
Attempting to set PLLA to 850 MHz ...
  plla_ctrl0 : 0000020a
  plla_ctrl1 : 00330000
  plla_ctrl2 : 0065008b
  plla_ctrl3 : 000000f1

PLLA Set


[If plugged s-ata drive]

U-Boot SPL 2013.10-g3a0f380-dirty (Jul 26 2014 - 14:31:34)
  Boot device: SATA
Attempting to set PLLA to 850 MHz ...
  plla_ctrl0 : 0000020a
  plla_ctrl1 : 00330000
  plla_ctrl2 : 0065008b
  plla_ctrl3 : 000000f1

PLLA Set
Bus 0: OK 
  Device 0: 
** File not found /boot/bootargs.bin **


U-Boot 2013.10-g3a0f380-dirty (Jul 26 2014 - 10:18:57) for OXNAS

DRAM:  256 MiB
IDE:   Bus 0: OK 
  Device 0: Model: HGST HTS545050A7E680 Firm: GR2OA230 Ser#: RB250AM5GJYGKP
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
NAND:  256 MiB
In:    serial
Out:   serial
Err:   serial
Net:   
Led:	GREEN
mii0
Main Loop
Hit any key to stop autoboot:  0 
ide - IDE sub-system

Usage:
ide reset - reset IDE controller
ide info  - show available IDE devices
ide device [dev] - show or set current device
ide part [dev] - print partition table of one or all IDE devices
ide read  addr blk# cnt
ide write addr blk# cnt - read/write `cnt' blocks starting at block `blk#'
    to/from memory address `addr'
4102704 bytes read in 656 ms (6 MiB/s)
1953812 bytes read in 353 ms (5.3 MiB/s)
7816 bytes read in 65 ms (117.2 KiB/s)
## Booting kernel from Legacy Image at 60500000 ...
   Image Name:   Linux-3.17.0-oxnas-tld-1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4102640 Bytes = 3.9 MiB
   Load Address: 60008000
   Entry Point:  60008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 60e00000 ...
   Image Name:   initramfs-3.17.0-oxnas-tld-1
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    1953748 Bytes = 1.9 MiB
   Load Address: 60000000
   Entry Point:  60000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 62c00000
   Booting using the fdt blob at 0x62c00000
   Loading Kernel Image ... OK
   Loading Ramdisk to 6fc4b000, end 6fe27fd4 ... OK
   Loading Device Tree to 6fc46000, end 6fc4ae87 ... OK

Led:	GREEN

Starting kernel ...

Uncompressing Linux... done, booting the kernel.

======
moderator edit: please use Formatted Code to post log.