Hi I am OpenWRT, working fine, I want to boot from Debian instead. What should I do. Can anyone help?
Here is my console log USB serial:
================
moderator edit: please used code tag to post log
Here is my console log USB serial:
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:42:03 -0700) ZyXEL NSA325 2-Bay Power Media Server SoC: Kirkwood 88F6282_A1 DRAM: 512 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 MV88E1318 PHY initialized on egiga0 Hit any key to stop autoboot: 0 ## Error: "setenv" not defined ubi0: attaching mtd1 ubi0: scanning is finished ubi0: attached mtd1 (name "mtd=2", size 126 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512 ubi0: VID header offset: 512 (aligned 512), data offset: 2048 ubi0: good PEBs: 1012, bad PEBs: 2, corrupted PEBs: 0 ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1062167026 ubi0: available PEBs: 0, total reserved PEBs: 1012, PEBs reserved for bad PEB handling: 18 Read 0 bytes from volume kernel to 800000 No size specified -> Using max size (2193408) ## Booting kernel from Legacy Image at 00800000 ... Image Name: ARM OpenWrt Linux-4.14.167 Created: 2020-01-29 16:05:35 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2081576 Bytes = 2 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.14.167 (builder@buildhost) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r10911-c155900f66)) #0 Wed Jan 29 16:05:35 2020 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: ZyXEL NSA325 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] random: get_random_bytes called from 0xc0700980 with crng_init=0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttyS0,115200 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 512108K/524288K available (4804K kernel code, 162K rwdata, 728K rodata, 1024K init, 208K bss, 12180K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc05b1030 (5797 kB) [ 0.000000] .init : 0xc0700000 - 0xc0800000 (1024 kB) [ 0.000000] .data : 0xc0800000 - 0xc0828ba0 ( 163 kB) [ 0.000000] .bss : 0xc0828ba0 - 0xc085cf84 ( 209 kB) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000007] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.000033] Switching to timer-based delay loop, resolution 5ns [ 0.000099] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.000119] pid_max: default: 32768 minimum: 301 [ 0.000232] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000248] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000703] CPU: Testing write buffer coherency: ok [ 0.001337] Setting up static identity map for 0x100000 - 0x10003c [ 0.001556] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1 [ 0.004639] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.004659] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.004732] pinctrl core: initialized pinctrl subsystem [ 0.005618] NET: Registered protocol family 16 [ 0.005888] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.006687] cpuidle: using governor ladder [ 0.006977] Feroceon L2: Enabling L2 [ 0.007009] Feroceon L2: Cache support initialised. [ 0.007216] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set [ 0.009953] No ATAGs? [ 0.021947] SCSI subsystem initialized [ 0.022451] usbcore: registered new interface driver usbfs [ 0.022493] usbcore: registered new interface driver hub [ 0.022533] usbcore: registered new device driver usb [ 0.023913] clocksource: Switched to clocksource orion_clocksource [ 0.024512] NET: Registered protocol family 2 [ 0.024954] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.025008] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.025058] TCP: Hash tables configured (established 4096 bind 4096) [ 0.025115] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.025134] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.025235] NET: Registered protocol family 1 [ 0.026079] Crashlog allocated RAM at address 0x3f00000 [ 0.027254] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.030498] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.030509] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.036053] io scheduler noop registered [ 0.036064] io scheduler deadline registered (default) [ 0.036950] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 0.038032] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 0.038047] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 0.038055] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 0.038064] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.038236] PCI: bus0: Fast back to back transfers disabled [ 0.038247] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.038592] PCI: bus1: Fast back to back transfers disabled [ 0.038630] pci 0000:00:01.0: BAR 8: assigned [mem 0xe0000000-0xe00fffff] [ 0.038643] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe0001fff 64bit] [ 0.038661] pci 0000:00:01.0: PCI bridge to [bus 01] [ 0.038672] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00fffff] [ 0.038709] pci 0000:00:01.0: enabling device (0140 -> 0142) [ 0.038726] pci 0000:01:00.0: enabling device (0140 -> 0142) [ 0.039077] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.040418] console [ttyS0] disabled [ 0.040473] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A [ 0.541530] console [ttyS0] enabled [ 0.545853] sata_mv f1080000.sata: slots 32 ports 2 [ 0.553145] scsi host0: sata_mv [ 0.556696] scsi host1: sata_mv [ 0.559954] ata1: SATA max UDMA/133 irq 32 [ 0.564082] ata2: SATA max UDMA/133 irq 32 [ 0.568565] nand: device found, Manufacturer ID: 0x92, Chip ID: 0xf1 [ 0.574964] nand: Eon NAND 128MiB 3,3V 8-bit [ 0.579254] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 0.586865] Scanning device for bad blocks [ 0.595779] Bad eraseblock 100 at 0x000000c80000 [ 0.605161] Bad eraseblock 200 at 0x000001900000 [ 0.648855] 3 fixed-partitions partitions found on MTD device orion_nand [ 0.655589] Creating 3 MTD partitions on "orion_nand": [ 0.660746] 0x000000000000-0x0000000c0000 : "uboot" [ 0.666062] 0x0000000c0000-0x000000140000 : "uboot_env" [ 0.671666] 0x000000140000-0x000008000000 : "ubi" [ 0.677468] libphy: Fixed MDIO Bus: probed [ 0.681765] libphy: orion_mdio_bus: probed [ 0.688003] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 0.696141] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 5c:f4:ab:50:0d:b2 [ 0.704944] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.711500] ehci-pci: EHCI PCI platform driver [ 0.716006] ehci-orion: EHCI orion driver [ 0.720169] orion-ehci f1050000.ehci: EHCI Host Controller [ 0.725714] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 0.733487] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000 [ 0.763922] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 0.770342] hub 1-0:1.0: USB hub found [ 0.774261] hub 1-0:1.0: 1 port detected [ 0.778524] usbcore: registered new interface driver usb-storage [ 0.784716] i2c /dev entries driver [ 0.789056] orion_wdt: Initial timeout 21 sec [ 0.798023] marvell-cesa f1030000.crypto: CESA device successfully registered [ 0.805851] NET: Registered protocol family 10 [ 0.811591] Segment Routing with IPv6 [ 0.815345] NET: Registered protocol family 17 [ 0.819826] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 0.832844] 8021q: 802.1Q VLAN Support v1.8 [ 0.839447] UBI: auto-attach mtd2 [ 0.842787] ubi0: attaching mtd2 [ 1.016837] ubi0: scanning is finished [ 1.020699] ata1: SATA link down (SStatus 0 SControl F300) [ 1.037079] ubi0: attached mtd2 (name "ubi", size 126 MiB) [ 1.042592] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes [ 1.049528] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512 [ 1.056265] ubi0: VID header offset: 512 (aligned 512), data offset: 2048 [ 1.063082] ubi0: good PEBs: 1012, bad PEBs: 2, corrupted PEBs: 0 [ 1.069204] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128 [ 1.076463] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1062167026 [ 1.085642] ubi0: available PEBs: 0, total reserved PEBs: 1012, PEBs reserved for bad PEB handling: 18 [ 1.095496] block ubiblock0_1: created from ubi0:1(rootfs) [ 1.101006] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem [ 1.108146] hctosys: unable to open rtc device (rtc0) [ 1.113517] ubi0: background thread "ubi_bgt0d" started, PID 462 [ 1.183926] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 1.355167] ata2: SATA link down (SStatus 0 SControl F300) [ 1.364090] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 1.374165] Freeing unused kernel memory: 1024K [ 1.474552] hub 1-1:1.0: USB hub found [ 1.478751] hub 1-1:1.0: 4 ports detected [ 1.533941] random: fast init done [ 1.608514] init: Console is alive [ 1.612041] init: - watchdog - [ 1.731786] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 1.790017] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 1.795329] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2 [ 1.803066] xhci_hcd 0000:01:00.0: hcc params 0x014042cb hci version 0x96 quirks 0x0000000000000004 [ 1.812929] hub 2-0:1.0: USB hub found [ 1.816886] hub 2-0:1.0: 2 ports detected [ 1.821179] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 1.826467] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3 [ 1.833919] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed [ 1.840535] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.849024] hub 3-0:1.0: USB hub found [ 1.852952] hub 3-0:1.0: 2 ports detected [ 1.858404] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 1.875948] init: - preinit - [ 1.940393] usb 1-1.2: new high-speed USB device number 3 using orion-ehci [ 2.131277] random: procd: uninitialized urandom read (4 bytes read) [ 2.137941] usb-storage 1-1.2:1.0: USB Mass Storage device detected [ 2.152382] scsi host2: usb-storage 1-1.2:1.0 [ 2.300250] random: jshn: uninitialized urandom read (4 bytes read) [ 2.328254] random: jshn: uninitialized urandom read (4 bytes read) [ 2.599267] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [ 2.609178] mv643xx_eth_port mv643xx_eth_port.0 eth0: link down [ 2.615966] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 3.205067] scsi 2:0:0:0: Direct-Access SanDisk' Cruzer Fit 1.00 PQ: 0 ANSI: 6 [ 3.214650] sd 2:0:0:0: [sda] 123174912 512-byte logical blocks: (63.1 GB/58.7 GiB) [ 3.223010] sd 2:0:0:0: [sda] Write Protect is off [ 3.228509] sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 3.244417] sda: sda1 [ 3.249388] sd 2:0:0:0: [sda] Attached SCSI removable disk [ 5.482881] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [ 5.492798] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 5.771671] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 585 [ 5.804683] UBIFS (ubi0:2): recovery needed [ 5.949707] UBIFS (ubi0:2): recovery completed [ 5.954256] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data" [ 5.962120] UBIFS (ubi0:2): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 5.972092] UBIFS (ubi0:2): FS size: 122314752 bytes (116 MiB, 948 LEBs), journal size 6064128 bytes (5 MiB, 47 LEBs) [ 5.982751] UBIFS (ubi0:2): reserved for root: 4952683 bytes (4836 KiB) [ 5.989406] UBIFS (ubi0:2): media format: w4/r0 (latest is w5/r0), UUID 3BFA64AE-764E-418C-9E10-3BEEB7FF0840, small LPT model [ 6.003887] mount_root: switching to ubifs overlay [ 6.018667] urandom-seed: Seeding with /etc/urandom.seed [ 6.073852] procd: - early - [ 6.077201] procd: - watchdog - [ 6.665873] procd: - watchdog - [ 6.669183] procd: - ubus - [ 6.730913] urandom_read: 3 callbacks suppressed [ 6.730918] random: ubusd: uninitialized urandom read (4 bytes read) [ 6.742883] random: ubusd: uninitialized urandom read (4 bytes read) [ 6.749522] random: ubusd: uninitialized urandom read (4 bytes read) [ 6.756583] procd: - init - Please press Enter to activate this console. [ 7.066032] kmodloader: loading kernel modules from /etc/modules.d/* [ 7.086134] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 7.104688] ip_tables: (C) 2000-2006 Netfilter Core Team [ 7.114027] nf_conntrack version 0.5.0 (8192 buckets, 32768 max) [ 7.162928] rtc-pcf8563 0-0051: rtc core: registered rtc-pcf8563 as rtc0 [ 7.176144] urngd: v1.0.2 started. [ 7.190138] xt_time: kernel timezone is -0000 [ 7.217190] PPP generic driver version 2.4.2 [ 7.222779] NET: Registered protocol family 24 [ 7.235602] kmodloader: done loading kernel modules from /etc/modules.d/* [ 7.267275] random: crng init done [ 7.270694] random: 1 urandom warning(s) missed due to ratelimiting [ 11.358094] br-lan: port 1(eth0) entered blocking state [ 11.363348] br-lan: port 1(eth0) entered disabled state [ 11.368790] device eth0 entered promiscuous mode [ 11.395581] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 14.038865] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled [ 14.048789] br-lan: port 1(eth0) entered blocking state [ 14.054051] br-lan: port 1(eth0) entered forwarding state [ 14.060469] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
================
moderator edit: please used code tag to post log