First of all I'm new to this and have a second-hand NAS, so I'm pretty sure I've missed something.
I'm booting from USB, with the 5.2.9 kernel. The boot looks like this:
If I'd plug the device to the network no address
In my own troubleshooting I wanted to upgrade u-boot, but I didn't got past kwboot:
So I'm kind of stuck here.
ENV:
I'm booting from USB, with the 5.2.9 kernel. The boot looks like this:
NSA325> reset
resetting ...
U-Boot 2014.07-tld-4 (Aug 02 2015 - 00:40:12)
ZyXEL NSA325 2-Bay Power Media Server
SoC: Kirkwood 88F6282_??
DRAM: 512 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0 [PRIME]
MV88E1318 PHY initialized on egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
4975125 bytes read in 651 ms (7.3 MiB/s)
9713936 bytes read in 708 ms (13.1 MiB/s)
## Booting kernel from Legacy Image at 02000000 ...
Image Name: Linux-5.2.9-kirkwood-tld-1
Created: 2020-12-21 13:08:27 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4975061 Bytes = 4.7 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-5.2.9-kirkwood-tld-1
Created: 2019-08-25 2:22:50 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 9713872 Bytes = 9.3 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
And that's it. I can leave it hanging. I've tried disconnecting the USB-TTL, reconnecting, nothing is printed, but the device is there.
If I'd plug the device to the network no address
In my own troubleshooting I wanted to upgrade u-boot, but I didn't got past kwboot:
❯ kwboot -t -B 115200 /dev/ttyUSB0 -b uboot.2017.07-tld-1.nsa325.mtd0.kwb Sending boot message. Please reboot the target...- Sending boot image... 4@�����>PC��0������ 0 % [+xmodem: Operation canceled
So I'm kind of stuck here.
ENV:
NSA325> env print CONTRY_TYPE=FF FEATURE_BIT=00 MODEL_ID=AE03 PRODUCT_NAME=NSA-325v2 VENDOR_NAME=MitraStar Technology Corp. arcNumber=4495 autoload=no baudrate=115200 bootargs=console=ttyS0,115200 mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) roo t=LABEL=rootfs loglevel=8 bootargs_end=:::orion:eth0:none bootargs_linux=console=ttyS0,115200 mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs 2) root=LABEL=rootfs loglevel=8 bootargs_root=root=/dev/nfs rw bootargs_stock=console=ttyS0,115200 mtdparts=orion_nand:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs 2) root=/dev/nfs rw init=/init bootcmd=run bootcmd_usb bootcmd_flash=setenv bootargs $bootargs_linux; nand read.e $loadaddr 0x4640000 0xA00000; nand read.e $uinitrdaddr 0x5040000 0xA00000; bootm $loadaddr 0x01100000 bootcmd_ide=setenv bootargs $bootargs_linux; ide reset; ext2load ide 0:1 $loadaddr /boot/uImage; ext2load ide 0:1 $uinitrdaddr /boot/uInitrd; bootm $loadaddr 0x01100000 bootcmd_linux=setenv bootargs $bootargs_linux; nand read.e $loadaddr 0x4640000 0xA00000; nand read.e $uinitrdaddr 0x5040000 0xA00000; bootm $loadaddr 0x01100000 bootcmd_stock=setenv bootargs $bootargs_stock; nand read.e $loadaddr $kernel_addr 0xA00000; bootm $loadaddr bootcmd_usb=setenv bootargs $bootargs_linux; run usb_init; run usb_boot; bootdelay=2 bootzcmd_usb=setenv bootargs $bootargs_linux; run usb_init; run usb_bootz; console=console=ttyS0,115200 mtdparts=orion_nand:0xc0000@0(uboot)ro,0x7f00000@0x100000(root) device=0:1 disL2Cache=no disL2Prefetch=yes disaMvPnp=no enaAutoRecovery=yes enaCpuStream=no enaDCPref=yes enaICPref=yes enaMonExt=no enaWrAllo=no ethact=egiga0 ethaddr=10:7B:EF:FA:37:52 ethmtu=1500 ethprime=egiga0 fdtaddr=0x1c00000 image_multi=yes image_name=uImage ipaddr=10.4.52.165 kernel_addr=0x4640000 lcd0_enable=0 lcd0_params=640x480-16@60 loadaddr=0x02000000 loadadr=0x2000000 loads_echo=0 mainlineLinux=yes mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo nandEcc=1bit netbsd_en=no netmask=255.255.255.0 netretry=no pcieTune=no pcieTune1=no pexMode=RC rcvrip=169.254.100.100 rootpath=/srv/ubuntu run_diag=yes sata_dma_mode=yes serverip=10.4.52.7 setL2CacheWT=yes standalone=fsload 0x2000000 $image_name;setenv bootargs $console root=/dev/mtdblock0 rw ip=$ipaddr:$serverip$bootargs_end $mvPhoneConfig; bootm 0x2000000; stderr=serial stdin=serial stdout=serial to_linux=setenv mainlineLinux yes; setenv bootcmd 'run bootcmd_linux'; saveenv; reset to_stock=setenv mainlineLinux no; setenv bootcmd 'run bootcmd_stock'; saveenv; reset uinitrdaddr=0x01100000 usb0Mode=host usb_boot=mw $loadaddr 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm $loadaddr $uinitrdaddr; else bootm $loadaddr; fi usb_bootz=mw $loadaddr 0 1; run usb_load_zimage; run usb_load_fdt; if run usb_load_uinitrd; then bootz $loadaddr $uinitrdaddr $fdtaddr; else bootm $loadaddr - $fdtaddr; fi usb_init=usb start usb_load_fdt=ext2load usb 0:1 $fdtaddr /dts/kirkwood-nsa325.dtb usb_load_uimage=ext2load usb $device $loadaddr /uImage usb_load_uinitrd=ext2load usb $device $uinitrdaddr /uInitrd usb_load_zimage=ext2load usb $device $loadaddr /vmlinuz vxworks_en=no yuk_ethaddr=00:00:00:EE:51:81 Environment size: 3714/131068 bytes