Hi all,
First, excuse my english, i'm from france and sometimes it's not so easy...
Since 1 week i hope to unbrick my DS414j... Without success...
I tryed this procedure : https://forum.doozan.com/read.php?3,100059
But it seems that i missed something as you can see below :
When i try the next step, it stay on this :
Do i have to trash it ??
First, excuse my english, i'm from france and sometimes it's not so easy...
Since 1 week i hope to unbrick my DS414j... Without success...
I tryed this procedure : https://forum.doozan.com/read.php?3,100059
But it seems that i missed something as you can see below :
uloader 2011.06.0 (Sep 11 2014 - 13:33:44)
Board: Mindspeed C2000
c2k_spi_probe
DDR Training:
...............................................................................e
Read offset: 0f,0c,0c,09
Write offset: 04,41,04,07
Copying Barebox from SPI Flash(bootopt=0)
BB Copying Done
## Starting Barebox at 0x01000000 ...
barebox 2011.06.0-dirty (Sep 11 2014 - 13:33:21)
Board: Mindspeed C2000
c2k_spi_probe
c2k_otp_probe.
cbus_baseaddr: 9c000000, ddr_baseaddr: 03800000, ddr_phys_baseaddr: 03800000
class init complete
tmu init complete
bmu1 init: done
bmu2 init: done
util init complete
GPI1 init complete
GPI2 init complete
HGPI init complete
HIF rx desc: base_va: 03e80000, base_pa: 03e80000
HIF tx desc: base_va: 03e80400, base_pa: 03e80400
HIF init complete
bmu1 enabled
bmu2 enabled
pfe_hw_init: done
pfe_firmware_init
pfe_load_elf
pfe_load_elf no of sections: 10
pfe_firmware_init: class firmware loaded
pfe_load_elf
pfe_load_elf no of sections: 10
pfe_firmware_init: tmu firmware loaded
pfe_load_elf
pfe_load_elf no of sections: 14
pfe_firmware_init: util firmware loaded
gemac_port
gemac_port
miidev_restart_aneg for PHY1
miidev_restart_aneg for PHY1
miidev_restart_aneg for PHY0
miidev_restart_aneg for PHY0
cfi_probe: cfi_flash base: 0xc0000000 size: 0x04000000
## Unknown FLASH on Bank at 0xc0000000 - Size = 0x00000000 = 0 MB
Using ENV from SPI Flash.
nand_probe: comcerto_nand base: 0xc8300000 size: 0x2048 MB
NAND type unknown: ff,ff
No NAND device found!!!
Malloc space: 0x00800000 -> 0x01000000 (size 8 MB)
Stack space : 0x007f8000 -> 0x00800000 (size 32 kB)
envfs: wrong magic on /dev/env0
no valid environment found on /dev/env0. Using default environment
running /env/bin/init...
Unknown command 'export' - try 'help'
=============================================
Synology Model: DS414j
barebox 2011.06.0-dirty (Sep 11 2014 - 13:33:21)
PLL0: 2400, PLL1: 1000, PLL2: 1500, PLL3: 1066 MHz
Ref Clock: 48 MHz
ARM Clock: 1200 MHz
AXI Clock: 250 MHz
DDR Clock: 533 MHz
IPSEC Clock: 300 MHz
C2K Revision: A1
DDR Width : 32
Fan 1: Good
Fan 2: Good
=============================================
Hit [Ctrl+C] to stop autoboot:
=============================================
Synology Model: DS414j
barebox 2011.06.0-dirty (Sep 11 2014 - 13:33:21)
PLL0: 2400, PLL1: 1000, PLL2: 1500, PLL3: 1066 MHz
Ref Clock: 48 MHz
ARM Clock: 1200 MHz
AXI Clock: 250 MHz
DDR Clock: 533 MHz
IPSEC Clock: 300 MHz
C2K Revision: A1
DDR Width : 32
Fan 1: Good
Fan 2: Good
=============================================
booting kernel of type uimage from /dev/spi0.kernel -r /dev/spi0.rootfs
use initrd /dev/spi0.rootfs
Verifying Checksum ... OK
Image Name: synology_comcerto2k_ds414j 25426
Created: 2020-05-11 22:01:02 UTC
Image Type: <NULL> <NULL> <NULL> (<NULL>)
Data Size: 3845029 Bytes = 3.7 MB
Load Address: 05000000
Entry Point: 05000000
Bad Magic Number
Barebox-C2K >/
When i try the next step, it stay on this :
kwboot -t -B 115200 /dev/ttyUSB0 -b u-boot-spl-2019.10-tld-1.ds414.kwb -a Sending boot message. Please reboot the target...
Do i have to trash it ??