Hey there,
I had Arch Linux running on my old Dockstar for a long time. But since a couple of years the box was stored in the shelf and I cannot find the USB storage device any longer. So I was trying to install Debian on a usb key and boot it but without success. I have access to the serial console and also managed to setup the netconsole for uboot.
The current uboot environment reads like:
When I execute run usb_boot I receive:
The usb device has been prepared with an ext2 filesystem and I copied https://github.com/pepaslabs/bodhi-kirkwood-rootfs-mirror/releases/tag/4.12.1 onto it.
Any ideas what I should do/check?
Cheers
Oleg
P.S. Forgot to mention that the device is currently not booting anything. When I just let uboot run through I get
I had Arch Linux running on my old Dockstar for a long time. But since a couple of years the box was stored in the shelf and I cannot find the USB storage device any longer. So I was trying to install Debian on a usb key and boot it but without success. I have access to the serial console and also managed to setup the netconsole for uboot.
The current uboot environment reads like:
arcNumber=2097 baudrate=115200 bootargs=console=ttyS0,115200 root=/dev/sda1 rootdelay=10 rootfstype=ext2 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) loglevel=7 netconsole=6666@192.168.178.200/eth0,6666@192.168.178.215/00:24:d7:4e:af:1c bootcmd=run bootcmd_usb; usb stop; run rescue_bootcmd; reset bootdelay=10 console=ttyS0,115200 ethact=egiga0 ethaddr=00:10:75:1A:DC:CE fileaddr=1000000 filesize=1BA0000 force_rescue=0 force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi if_netconsole=ping $serverip init=/usr/lib/systemd/systemd ipaddr=192.168.178.200 led_error=orange blinking led_exit=green off led_init=green blinking mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data) ncip=192.168.178.100 partition=nand0,2 pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi preboot=run if_netconsole start_netconsole rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi rescue_installed=0 rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params serverip=192.168.178.100 start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=nc stdin=nc stdout=nc ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi ubifs_mtd=3 ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params usb=0:1 usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot usb_custom_params=loglevel=7 netconsole=6666@192.168.178.200/eth0,6666@192.168.178.215/00:24:d7:4e:af:1c usb_device=0:1 usb_init=run usb_scan usb_root=/dev/sda1 usb_root_label=my-rootfs usb_rootdelay=10 usb_rootfs=UUID=d65382b6-c396-4a42-a42e-512e25edb2af usb_rootfstype=ext2 usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done usb_scan_1=usb=0:1 dev=sda1 usb_scan_2=usb=1:1 dev=sdb1 usb_scan_3=usb=2:1 dev=sdc1 usb_scan_4=usb=3:1 dev=sdd1 usb_scan_list=1 2 3 4 usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params
When I execute run usb_boot I receive:
Loading file "/boot/uImage" from usb device 0:1 (usbda1) Failed to mount ext2 filesystem... ** Bad ext2 partition or disk - usb 0:1 ** Loading file "/boot/uInitrd" from usb device 0:1 (usbda1) Failed to mount ext2 filesystem... ** Bad ext2 partition or disk - usb 0:1 ** Wrong Image Format for bootm command ERROR: can't get kernel image!
The usb device has been prepared with an ext2 filesystem and I copied https://github.com/pepaslabs/bodhi-kirkwood-rootfs-mirror/releases/tag/4.12.1 onto it.
Any ideas what I should do/check?
Cheers
Oleg
P.S. Forgot to mention that the device is currently not booting anything. When I just let uboot run through I get
U-Boot 2011.12 (Feb 12 2012 - 21:33:07) Seagate FreeAgent DockStar arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1 GNU ld (Sourcery G++ Lite 2009q3-67) 2.19.51.20090709 Hit any key to stop autoboot: 0 ## Error: "bootcmd_usb" not defined stopping USB.. ### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000 Scanning JFFS2 FS: ........ read_nand_cached: error reading nand off 0x1348400 size 8192 bytes read_nand_cached: error reading nand off 0x1480000 size 8192 bytes done. read_nand_cached: error reading nand off 0x1348c00 size 8192 bytes ### JFFS2 load complete: 524288 bytes loaded to 0x800000 ## Starting application at 0x00800200 ...