Boot hangs at "booting the kernel." (no replies)

I have a GoFlex Home that I have been trying to get working with Debian. I have the "kirkwood-debian_rootfs.img" (from davygravy: http://dl.dropbox.com/u/1015928/Kirkwood/rootfs_images/NSA320quickstart.tar.gz) on a USB flash drive. It Loads /boot/uImage and /boot/uInitrd the says its booting kernel and loading init Ramdisk but then hangs after that. Here is the bootlog:
U-Boot 2010.09 (Feb 16 2011 - 18:44:23)
UBIT v0.6 by Jeff Doozan and Peter Carmichael

SoC: Kirkwood 88F6281_A0
DRAM: 128 MiB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Creating 1 MTD partitions on "nand0":
0x000000700000-0x000010000000 : "mtd=2"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI error: validate_ec_hdr: bad VID header offset 2048, expected 512
UBI error: validate_ec_hdr: bad EC header
UBI error: ubi_io_read_ec_hdr: validation failed for PEB 0
UBI error: ubi_init: cannot attach mtd1
UBI error: ubi_init: UBI error: cannot initialize UBI, error -22
UBI init error -22
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:silent", error -19
Error reading superblock on volume 'ubi:silent'!
UBIFS not mounted, use ubifs mount to mount volume first!
Using egiga0 device
ping failed; host 10.10.10.5 is not alive
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Hit any key to stop autoboot: 0
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:fast", error -19
Error reading superblock on volume 'ubi:fast'!
UBIFS not mounted, use ubifs mount to mount volume first!
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
2279256 bytes read
Loading file "/uInitrd" from usb device 0:1 (usbda1)
** File not found /uInitrd
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
7004538 bytes read
## Booting kernel from Legacy Image at 00680000 ...
Image Name: Linux-3.3.2
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2279192 Bytes = 2.2 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-3.3.2-kirkwood-dg
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 7004474 Bytes = 6.7 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.


And this is my printenv:
bootcmd=run fast_boot; run usb_boot; run hd_boot; run ubi_boot
bootdelay=3
baudrate=115200
ide_start=ide reset
ubi_start=ubi part root
usb_start=usb start
nc_test=ping $ncip
nc_start=setenv stdin nc; setenv stdout nc; setenv stderr nc; version
silent_boot=run silent_rd ubi_args ubi_fallback
fast_boot=run fast_rd ubi_args ubi_fallback
usb_boot=for scan in 0 1 2 3; do run usb_args_$scan ext2_kern ext2_boot; run ext2_rd ubi_fallback; run fat_kern fat_boot; run fat_rd ubi_fallback;done
usb_args_0=boot_dev='usb 0:1'; dev_args='root=/dev/sda1 rootdelay=10'
usb_args_1=boot_dev='usb 1:1'; dev_args='root=/dev/sdb1 rootdelay=10'
usb_args_2=boot_dev='usb 2:1'; dev_args='root=/dev/sdc1 rootdelay=10'
usb_args_3=boot_dev='usb 3:1'; dev_args='root=/dev/sdd1 rootdelay=10'
hd_boot=run ide_start; for scan in 0 1; do run hd_args_$scan ext2_kern ext2_boot; run ext2_rd ubi_fallback; run fat_kern fat_boot; run fat_rd ubi_fallback; done
hd_args_0=boot_dev='ide 0:1'; dev_args='root=/dev/sda1'
hd_args_1=boot_dev='ide 1:1'; dev_args='root=/dev/sdb1'
ubi_boot=run ubi_rd ubi_args ubi_fallback
ubi_args=dev_args='ubi.mtd=root'
rescue=dev_args='ubi.mtd=root rootfstype=preboot'; boot_dev='usb 0:1'; run ext2_kern ext2_auto boot_rd; boot_dev='ide 0:1'; run ide_start ext2_kern ext2_auto boot_rd; run silent_rd ubi_fallback; run fast_rd ubi_fallback; run ubi_rd ubi_fallback
chain=nand read.e 0x800000 0x480000 0x80000; go 0x800200
ethact=egiga0
console=ttyS0,115200
mtdids=nand0=orion_nand
set_bootargs=setenv bootargs console=$console $mtdparts $dev_args $rd_args netconsole=@$ipaddr/eth0,@$ncipk/
ext2_kern=ext2load $boot_dev $addr_kern /boot/uImage
ext2_auto=ext2load $boot_dev $addr_rd /boot/uInitrd
ext2_rd=ext2load $boot_dev $addr_rd /uInitrd
ext2_boot=run ext2_rd boot_rd; run ext2_auto boot_auto; run boot_kern
fat_kern=fatload $boot_dev $addr_kern /boot/uImage
fat_rd=fatload $boot_dev $addr_rd /uInitrd
fat_boot=run fat_rd boot_rd
ubi_kern=ubifsmount boot; ubifsload $addr_kern /boot/uImage
ubi_rd=ubifsmount ramdisk; ubifsload $addr_rd /uInitrd
ubi_fallback=run ubi_kern boot_rd
silent_rd=ubifsmount silent; ubifsload $addr_rd /uInitrd
fast_rd=ubifsmount fast; ubifsload $addr_rd /uInitrd
boot_kern=run set_bootargs; bootm $addr_kern
boot_rd=run set_bootargs; bootm $addr_kern $addr_rd
boot_auto=rd_args='rootfstype=auto'; run boot_rd
addr_kern=0x680000
addr_rd=0x1100000
ncip=10.10.10.5
ncipk=10.10.10.4
led_init=green blinking
led_exit=green off
led_error=orange blinking
ethaddr=xx:xx:xx:xx:xx:xx
preboot=run ubi_start silent_boot; run nc_test nc_start; run usb_start
mtdparts=mtdparts=orion_nand:1M(u-boot),6M(uImage),-(root)
gatewayip=192.168.1.1
ipaddr=192.168.1.254
arch_number=0x00000831
usb_rootfstype=ext2
serverip=192.168.1.150
stdin=serial
stdout=serial
stderr=serial
partition=nand0,0
mtddevnum=0
mtddevname=u-boot

Environment size: 2825/131068 bytes

Any thoughts on what needs to be done to complete the boot?

Thanks in advance for any help!