My Debian 12 on USB stick stoped working rapidly. In one moment all services shouted down (and also SSH). If I try restart it stop during kernel loading. It is any way to fix it? It is USB failure?
Starting kernel ... [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 6.7.5-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 PREEMPT Sat Feb 17 16:27:56 PST 2024 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr =0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: ZyXEL NSA325 [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000001fffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000001f ffffff] [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=root fs rootdelay=10 mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x8 0000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1 ),0xA00000(kernel_2),0x2FC0000(rootfs2) [ 0.000000][ T0] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 32768 (order: 5, 131072 b ytes, linear) [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 12 9920 [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 497500K/524288K available (12288K kernel code, 17 81K rwdata, 5588K rodata, 1024K init, 309K bss, 26788K reserved, 0K cma-reserved ) [ 0.000000][ T0] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes= 1 [ 0.000000][ T0] trace event string verifier disabled [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay i s 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] rcu: srcu_init: Setting srcu_struct sizes based on conten tion. [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycl es: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000001][ T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps eve ry 10737418237ns [ 0.000083][ T0] Switching to timer-based delay loop, resolution 5ns [ 0.000779][ T0] Console: colour dummy device 80x30 [ 0.000844][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000) [ 0.000871][ T0] CPU: Testing write buffer coherency: ok [ 0.000986][ T0] pid_max: default: 32768 minimum: 301 [ 0.007771][ T0] LSM: initializing lsm=capability,integrity [ 0.009658][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 byte s, linear) [ 0.009690][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.020607][ T1] RCU Tasks: Setting shift to 0 and lim to 1 rcu_task_cb_ad just=1. [ 0.020923][ T1] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task _cb_adjust=1. [ 0.021330][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.021621][ T1] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1 [ 0.022039][ T1] rcu: Hierarchical SRCU implementation. [ 0.022053][ T1] rcu: Max phase no-delay instances is 1000. [ 0.024537][ T1] devtmpfs: initialized [ 0.034350][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffff ffff, max_idle_ns: 19112604462750000 ns [ 0.034389][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, lin ear) [ 0.037032][ T1] prandom: seed boundary self test passed [ 0.040352][ T1] prandom: 100 self tests passed [ 0.040373][ T1] pinctrl core: initialized pinctrl subsystem [ 0.043443][ T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.044144][ T1] DMA: preallocated 256 KiB pool for atomic coherent alloca tions [ 0.048347][ T1] audit: initializing netlink subsys (disabled) [ 0.049644][ T20] audit: type=2000 audit(0.040:1): state=initialized audit_ enabled=0 res=1 [ 0.051233][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.051373][ T1] cpuidle: using governor ladder [ 0.051452][ T1] cpuidle: using governor menu [ 0.051981][ T1] Feroceon L2: Enabling L2 [ 0.052012][ T1] Feroceon L2: Cache support initialised. [ 0.061292][ T1] No ATAGs? [ 0.420096][ T1] raid6: int32x8 gen() 152 MB/s [ 0.760096][ T1] raid6: int32x4 gen() 140 MB/s [ 1.100095][ T1] raid6: int32x2 gen() 182 MB/s [ 1.440096][ T1] raid6: int32x1 gen() 133 MB/s [ 1.440107][ T1] raid6: using algorithm int32x2 gen() 182 MB/s [ 1.780092][ T1] raid6: .... xor() 115 MB/s, rmw enabled [ 1.780101][ T1] raid6: using intx1 recovery algorithm [ 1.781557][ T1] SCSI subsystem initialized [ 1.782249][ T1] usbcore: registered new interface driver usbfs [ 1.782330][ T1] usbcore: registered new interface driver hub [ 1.782386][ T1] usbcore: registered new device driver usb [ 1.782685][ T1] pps_core: LinuxPPS API ver. 1 registered [ 1.782693][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodol fo Giometti <giometti@linux.it> [ 1.782718][ T1] PTP clock support registered [ 1.784983][ T1] vgaarb: loaded [ 1.785613][ T1] clocksource: Switched to clocksource orion_clocksource [ 1.798481][ T1] VFS: Disk quotas dquot_6.6.0 [ 1.798831][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.828711][ T1] NET: Registered PF_INET protocol family [ 1.829001][ T1] IP idents hash table entries: 8192 (order: 4, 65536 bytes , linear) [ 1.835805][ T1] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 1.835970][ T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 1.836020][ T1] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 1.836092][ T1] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 1.836634][ T1] TCP: Hash tables configured (established 4096 bind 4096) [ 1.837191][ T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes , linear) [ 1.837409][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear ) [ 1.837440][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, l inear) [ 1.838252][ T1] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 1.839337][ T1] RPC: Registered named UNIX socket transport module. [ 1.839348][ T1] RPC: Registered udp transport module. [ 1.839353][ T1] RPC: Registered tcp transport module. [ 1.839357][ T1] RPC: Registered tcp-with-tls transport module. [ 1.839361][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.839379][ T1] PCI: CLS 0 bytes, default 32 [ 2.559857][ T1] Initialise system trusted keyrings [ 2.559937][ T1] Key type blacklist registered [ 2.561081][ T1] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 2.561149][ T1] zbud: loaded [ 2.575083][ T1] NFS: Registering the id_resolver key type [ 2.575126][ T1] Key type id_resolver registered [ 2.575133][ T1] Key type id_legacy registered [ 2.575282][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering ... [ 2.575300][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Reg istering... [ 2.576739][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat , Inc. [ 2.577503][ T1] fuse: init (API version 7.39) [ 2.578708][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 2.578998][ T1] orangefs_init: module version upstream loaded [ 2.579295][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled [ 2.793246][ T1] xor: measuring software checksum speed [ 2.799882][ T1] arm4regs : 1492 MB/sec [ 2.810889][ T1] 8regs : 895 MB/sec [ 2.818652][ T1] 32regs : 1270 MB/sec [ 2.818660][ T1] xor: using function: arm4regs (1492 MB/sec) [ 2.818673][ T1] async_tx: api initialized (async) [ 2.818685][ T1] Key type asymmetric registered [ 2.818692][ T1] Asymmetric key parser 'x509' registered [ 2.825825][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 2.826268][ T1] io scheduler bfq registered [ 2.967991][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinc trl driver [ 2.969634][ T1] gpio gpiochip0: Static allocation of GPIO base is depreca ted, use dynamic allocation. [ 2.970620][ T1] gpio gpiochip1: Static allocation of GPIO base is depreca ted, use dynamic allocation. [ 2.971439][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: host bridge /mbus @f1000000/pcie@82000000 ranges: [ 2.971504][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f104 0000..0x00f1041fff -> 0x0000040000 [ 2.971539][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f104 4000..0x00f1045fff -> 0x0000044000 [ 2.971572][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f108 0000..0x00f1081fff -> 0x0000080000 [ 2.971604][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffff ffffffffff..0x00fffffffe -> 0x0100000000 [ 2.971634][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffff ffffffffff..0x00fffffffe -> 0x0100000000 [ 2.971664][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffff ffffffffff..0x00fffffffe -> 0x0200000000 [ 2.971685][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffff ffffffffff..0x00fffffffe -> 0x0200000000 [ 2.972307][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge t o bus 0000:00 [ 2.972324][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.972340][ T1] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf104 1fff] (bus address [0x00040000-0x00041fff]) [ 2.972354][ T1] pci_bus 0000:00: root bus resource [mem 0xf1044000-0xf104 5fff] (bus address [0x00044000-0x00045fff]) [ 2.972367][ T1] pci_bus 0000:00: root bus resource [mem 0xf1080000-0xf108 1fff] (bus address [0x00080000-0x00081fff]) [ 2.972379][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefff ffff] [ 2.972390][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 2.972490][ T1] pci 0000:00:01.0: [11ab:6282] type 01 class 0x060400 [ 2.973998][ T1] PCI: bus0: Fast back to back transfers disabled [ 2.974021][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-0 0]), reconfiguring [ 2.974243][ T1] pci 0000:01:00.0: [1033:0194] type 00 class 0x0c0330 [ 2.974282][ T1] pci 0000:01:00.0: reg 0x10: [mem 0x90000000-0x90001fff 64 bit] [ 2.974451][ T1] pci 0000:01:00.0: PME# supported from D0 D3hot [ 2.974527][ T1] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, li mited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 G T/s PCIe x1 link) [ 2.995709][ T1] PCI: bus1: Fast back to back transfers disabled [ 2.995730][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 2.995776][ T1] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00f ffff] [ 2.995796][ T1] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe0001 fff 64bit] [ 2.995821][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 2.995836][ T1] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xe00ff fff] [ 2.995972][ T1] pcieport 0000:00:01.0: enabling device (0140 -> 0142) [ 2.996912][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 3.057655][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 3.061491][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 3.117656][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 3.121748][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 3.123922][ T1] printk: legacy console [ttyS0] disabled [ 3.124463][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 28, base _baud = 12500000) is a 16550A [ 3.124521][ T1] printk: legacy console [ttyS0] enabled [ 4.249424][ T1] loop: module loaded [ 4.254182][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 4.263753][ T1] scsi host0: sata_mv [ 4.268936][ T1] scsi host1: sata_mv [ 4.273121][ T1] ata1: SATA max UDMA/133 irq 29 lpm-pol 0 [ 4.278853][ T1] ata2: SATA max UDMA/133 irq 29 lpm-pol 0 [ 4.285752][ T1] nand: device found, Manufacturer ID: 0x92, Chip ID: 0xf1 [ 4.292851][ T1] nand: Eon NAND 128MiB 3,3V 8-bit [ 4.297857][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 4.306205][ T1] Scanning device for bad blocks [ 4.315875][ T1] Bad eraseblock 100 at 0x000000c80000 [ 4.326016][ T1] Bad eraseblock 200 at 0x000001900000 [ 4.370790][ T1] 9 cmdlinepart partitions found on MTD device orion_nand [ 4.377813][ T1] Creating 9 MTD partitions on "orion_nand": [ 4.383711][ T1] 0x000000000000-0x000000100000 : "uboot" [ 4.390071][ T1] 0x000000100000-0x000000180000 : "stock_uboot_env" [ 4.397168][ T1] 0x000000180000-0x000000200000 : "key_store" [ 4.403710][ T1] 0x000000200000-0x000000280000 : "info" [ 4.409849][ T1] 0x000000280000-0x000000c80000 : "etc" [ 4.415906][ T1] 0x000000c80000-0x000001680000 : "kernel_1" [ 4.422362][ T1] 0x000001680000-0x000004640000 : "rootfs1" [ 4.428970][ T1] 0x000004640000-0x000005040000 : "kernel_2" [ 4.435473][ T1] 0x000005040000-0x000008000000 : "rootfs2" [ 4.442753][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 4.451362][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Ja son@zx2c4.com>. All Rights Reserved. [ 4.467354][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 4.476815][ T1] mv643xx_eth: Set the PHY to fix link down [ 4.477604][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 5c:f4:ab:50:13:2c [ 4.493434][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 4.499823][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigne d bus number 1 [ 4.508489][ T1] orion-ehci f1050000.ehci: irq 32, io mem 0xf1050000 [ 4.535633][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 4.542742][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct= 0002, bcdDevice= 6.07 [ 4.551801][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, Seria lNumber=1 [ 4.559797][ T1] usb usb1: Product: EHCI Host Controller [ 4.565429][ T1] usb usb1: Manufacturer: Linux 6.7.5-kirkwood-tld-1 ehci_h cd [ 4.572805][ T1] usb usb1: SerialNumber: f1050000.ehci [ 4.579182][ T1] hub 1-0:1.0: USB hub found [ 4.583727][ T1] hub 1-0:1.0: 1 port detected [ 4.589415][ T1] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 4.595413][ T1] xhci_hcd 0000:01:00.0: new USB bus registered, assigned b us number 2 [ 4.603986][ T1] xhci_hcd 0000:01:00.0: hcc params 0x014042cb hci version 0x96 quirks 0x0000000000000004 [ 4.614425][ T1] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 4.620622][ T1] xhci_hcd 0000:01:00.0: new USB bus registered, assigned b us number 3 [ 4.628790][ T1] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed [ 4.636019][ T1] usb usb2: New USB device found, idVendor=1d6b, idProduct= 0002, bcdDevice= 6.07 [ 4.645027][ T1] usb usb2: New USB device strings: Mfr=3, Product=2, Seria lNumber=1 [ 4.653008][ T1] usb usb2: Product: xHCI Host Controller [ 4.658627][ T1] usb usb2: Manufacturer: Linux 6.7.5-kirkwood-tld-1 xhci-h cd [ 4.665986][ T1] usb usb2: SerialNumber: 0000:01:00.0 [ 4.672108][ T1] hub 2-0:1.0: USB hub found [ 4.676684][ T1] hub 2-0:1.0: 2 ports detected [ 4.682163][ T1] usb usb3: We don't know the algorithms for LPM for this h ost, disabling LPM. [ 4.691217][ T1] usb usb3: New USB device found, idVendor=1d6b, idProduct= 0003, bcdDevice= 6.07 [ 4.700251][ T1] usb usb3: New USB device strings: Mfr=3, Product=2, Seria lNumber=1 [ 4.708389][ T1] usb usb3: Product: xHCI Host Controller [ 4.713993][ T1] usb usb3: Manufacturer: Linux 6.7.5-kirkwood-tld-1 xhci-h cd [ 4.721356][ T1] usb usb3: SerialNumber: 0000:01:00.0 [ 4.727858][ T1] hub 3-0:1.0: USB hub found [ 4.732374][ T1] hub 3-0:1.0: 2 ports detected [ 4.738273][ T1] usbcore: registered new interface driver usb-storage [ 4.745559][ T1] mousedev: PS/2 mouse device common for all mice [ 4.752287][ T1] i2c_dev: i2c /dev entries driver [ 4.760621][ T1] rtc-pcf8563 0-0051: registered as rtc0 [ 4.767638][ T1] rtc-pcf8563 0-0051: setting system clock to 2024-04-28T07 :32:44 UTC (1714289564) [ 4.778924][ T1] device-mapper: uevent: version 1.0.3 [ 4.784821][ T1] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialis ed: dm-devel@redhat.com [ 4.794104][ T53] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 4.801921][ T1] device-mapper: multipath round-robin: version 1.2.0 loade d [ 4.809506][ T1] device-mapper: multipath queue-length: version 0.2.0 load ed [ 4.817126][ T53] ata1.00: ATA-9: WDC WD30EFRX-68EUZN0, 80.00A80, max UDMA/ 133 [ 4.824565][ T53] ata1.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31 /32) [ 4.832122][ T1] device-mapper: multipath service-time: version 0.3.0 load ed [ 4.839820][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 4.848162][ T1] sdhci: Secure Digital Host Controller Interface driver [ 4.855375][ T53] ata1.00: configured for UDMA/133 [ 4.860399][ T1] sdhci: Copyright(c) Pierre Ossman [ 4.868416][ T1] ledtrig-cpu: registered to indicate activity on CPUs [ 4.875287][ T1] hid: raw HID events driver (C) Jiri Kosina [ 4.881704][ T19] scsi 0:0:0:0: Direct-Access ATA WDC WD30EFRX-68E 0A80 PQ: 0 ANSI: 5 [ 4.890591][ T49] usb 1-1: new high-speed USB device number 2 using orion-e hci [ 4.899968][ T19] sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3. 00 TB/2.73 TiB) [ 4.909273][ T1] drop_monitor: Initializing network drop monitor service [ 4.916392][ T19] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 4.922417][ T19] sd 0:0:0:0: [sda] Write Protect is off [ 4.929399][ T1] NET: Registered PF_INET6 protocol family [ 4.935520][ T19] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabl ed, doesn't support DPO or FUA [ 4.947694][ T1] Segment Routing with IPv6 [ 4.952084][ T1] RPL Segment Routing with IPv6 [ 4.957065][ T19] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 4.964527][ T1] In-situ OAM (IOAM) with IPv6 [ 4.970536][ T1] NET: Registered PF_PACKET protocol family [ 4.976983][ T1] Key type dns_resolver registered [ 4.998559][ T1] registered taskstats version 1 [ 5.003494][ T1] Loading compiled-in X.509 certificates [ 5.032692][ T19] sda: sda1 sda2 [ 5.045161][ T19] sd 0:0:0:0: [sda] Attached SCSI disk [ 5.051340][ T1] Key type .fscrypt registered [ 5.056199][ T1] Key type fscrypt-provisioning registered [ 5.066876][ T1] Key type big_key registered [ 5.081817][ T1] Key type encrypted registered [ 5.115434][ T49] usb 1-1: New USB device found, idVendor=05e3, idProduct=0 608, bcdDevice=85.32 [ 5.140810][ T49] usb 1-1: New USB device strings: Mfr=0, Product=1, Serial Number=0 [ 5.152451][ T116] "cryptomgr_test" (116) uses obsolete ecb(arc4) skcipher [ 5.159838][ T49] usb 1-1: Product: USB2.0 Hub [ 5.165741][ T49] hub 1-1:1.0: USB hub found [ 5.175764][ T49] hub 1-1:1.0: 4 ports detected [ 5.415654][ T55] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 5.435804][ T55] ata2.00: ATA-9: WDC WD30EFRX-68EUZN0, 80.00A80, max UDMA/ 133 [ 5.443272][ T55] ata2.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31 /32) [ 5.468175][ T55] ata2.00: configured for UDMA/133 [ 5.483691][ T11] scsi 1:0:0:0: Direct-Access ATA WDC WD30EFRX-68E 0A80 PQ: 0 ANSI: 5 [ 5.495647][ T49] usb 1-1.2: new high-speed USB device number 3 using orion -ehci [ 5.507150][ T19] sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3. 00 TB/2.73 TiB) [ 5.525733][ T19] sd 1:0:0:0: [sdb] 4096-byte physical blocks [ 5.540822][ T19] sd 1:0:0:0: [sdb] Write Protect is off [ 5.555765][ T19] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabl ed, doesn't support DPO or FUA [ 5.575732][ T19] sd 1:0:0:0: [sdb] Preferred minimum I/O size 4096 bytes [ 5.649511][ T19] sdb: sdb1 sdb2 [ 5.653878][ T19] sd 1:0:0:0: [sdb] Attached SCSI disk [ 5.687493][ T49] usb 1-1.2: New USB device found, idVendor=0951, idProduct =1666, bcdDevice= 1.10 [ 5.705629][ T49] usb 1-1.2: New USB device strings: Mfr=1, Product=2, Seri alNumber=3 [ 5.713681][ T49] usb 1-1.2: Product: DataTraveler 3.0 [ 5.735632][ T49] usb 1-1.2: Manufacturer: Kingston [ 5.740712][ T49] usb 1-1.2: SerialNumber: 00241D8CE55DBFA1D975AEC0 [ 5.756581][ T49] usb-storage 1-1.2:1.0: USB Mass Storage device detected [ 5.776156][ T49] scsi host2: usb-storage 1-1.2:1.0 [ 6.806688][ T19] scsi 2:0:0:0: Direct-Access Kingston DataTraveler 3.0 PMAP PQ: 0 ANSI: 6 [ 6.827397][ T11] sd 2:0:0:0: [sdc] 30277632 512-byte logical blocks: (15.5 GB/14.4 GiB) [ 6.836271][ T11] sd 2:0:0:0: [sdc] Write Protect is off [ 6.845765][ T11] sd 2:0:0:0: [sdc] Write cache: disabled, read cache: enab led, doesn't support DPO or FUA [ 6.965603][ T11] sdc: sdc1 [ 6.969270][ T11] sd 2:0:0:0: [sdc] Attached SCSI removable disk [ 7.072806][ T1] clk: Disabling unused clocks [ 7.078279][ T1] Waiting 10 sec before mounting root device... [ 17.125643][ T1] md: Waiting for all devices to be available before autode tect [ 17.133173][ T1] md: If you don't use raid, use raid=noautodetect [ 17.139643][ T1] md: Autodetecting RAID arrays. [ 17.144457][ T1] md: autorun ... [ 17.147978][ T1] md: ... autorun DONE. [ 17.152774][ T1] /dev/root: Can't open blockdev [ 17.157658][ T1] VFS: Cannot open root device "LABEL=rootfs" or unknown-bl ock(0,0): error -6 [ 17.166449][ T1] Please append a correct "root=" boot option; here are the available partitions: [ 17.175557][ T1] 0800 2930266584 sda [ 17.175567][ T1] driver: sd [ 17.183151][ T1] 0801 498688 sda1 274271a6-1ed6-41ac-8487-c6bf3 9bd7334 [ 17.183162][ T1] [ 17.193209][ T1] 0802 2929766400 sda2 4b5ac66c-943d-4c75-9d62-918d1 185b731 [ 17.193220][ T1] [ 17.203237][ T1] 0810 2930266584 sdb [ 17.203248][ T1] driver: sd [ 17.210815][ T1] 0811 498688 sdb1 a05eb507-95c4-44cb-ba90-ce63e 4b616d8 [ 17.210827][ T1] [ 17.220819][ T1] 0812 2929766400 sdb2 9bc55b98-0312-49f0-b9f0-30d18 71ffe9e [ 17.220830][ T1] [ 17.230820][ T1] 0820 15138816 sdc [ 17.230829][ T1] driver: sd [ 17.238376][ T1] 0821 15137792 sdc1 38cae43a-01 [ 17.238385][ T1] [ 17.246201][ T1] List of all bdev filesystems: [ 17.250927][ T1] ext3 [ 17.250932][ T1] ext4 [ 17.253561][ T1] exfat [ 17.256209][ T1] fuseblk [ 17.258933][ T1] xfs [ 17.261827][ T1] f2fs [ 17.264374][ T1] [ 17.269216][ T1] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 17.278214][ T1] CPU: 0 PID: 1 Comm: swapper Not tainted 6.7.5-kirkwood-tl d-1 #1 af9b82eecabd869882a37de3f6143b1936c0ec09 [ 17.289486][ T1] Hardware name: Marvell Kirkwood (Flattened Device Tree) [ 17.296488][ T1] unwind_backtrace from show_stack+0x10/0x14 [ 17.302463][ T1] show_stack from dump_stack_lvl+0x28/0x30 [ 17.308254][ T1] dump_stack_lvl from panic+0xf0/0x324 [ 17.313686][ T1] panic from mount_root_generic+0x1c8/0x2a0 [ 17.319555][ T1] mount_root_generic from prepare_namespace+0x1b8/0x244 [ 17.326469][ T1] prepare_namespace from kernel_init_freeable+0x1b4/0x208 [ 17.333568][ T1] kernel_init_freeable from kernel_init+0x10/0x130 [ 17.340056][ T1] kernel_init from ret_from_fork+0x14/0x28 [ 17.345835][ T1] Exception stack(0xa0819fb0 to 0xa0819ff8) [ 17.351612][ T1] 9fa0: 00000000 000000 00 00000000 00000000 [ 17.360533][ T1] 9fc0: 00000000 00000000 00000000 00000000 00000000 000000 00 00000000 00000000 [ 17.369453][ T1] 9fe0: 00000000 00000000 00000000 00000000 00000013 000000 00 [ 17.376800][ T1] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) ]---