Unbrick Stora MS2000 (no replies)

Hi guys!
I tried to switch to openwrt on my Stora MS2000
I did everything according to the instructions, but at step

tftp 0x0800000 u-boot.kwb
nand erase 0x0 100000
nand write 0x0800000 0x0 0x100000
reset

In the nand write line I wrote nand write 0x0800000 0x0 0x10000 (I skipped 0) and after that, it does not respond, there is nothing in the terminal either

Now when loading u-boot my log looks like this:

  __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|
 ** MARVELL BOARD: RD-88F6281A LE
  
U-Boot 1.1.4 (Sep  4 2009 - 09:36:11) Marvell version: 3.4.14
  
U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CEE60
  
Soc: MV88F6281 Rev 3 (DDR2)
CPU running @ 1000Mhz L2 running @ 333Mhz
SysClock = 333Mhz , TClock = 200Mhz
  
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size  64MB
DRAM CS[1] base 0x04000000   size  64MB
DRAM Total size 128MB  16bit width
Flash:  0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB
CRC in Flash: ffffffff, Calculated CRC: 619d86db
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
## Error: environment overflow, "stdin" deleted
## Error: environment overflow, "stdout" deleted
## Error: environment overflow, "stderr" deleted
  
CPU : Marvell Feroceon (Rev 1)
## Error: environment overflow, "console" deleted
## Error: environment overflow, "mainlineLinux" deleted
## Error: environment overflow, "CASset" deleted
## Error: environment overflow, "enaMonExt" deleted
## Error: environment overflow, "enaCpuStream" deleted
## Error: environment overflow, "enaWrAllo" deleted
## Error: environment overflow, "pexMode" deleted
## Error: environment overflow, "disL2Cache" deleted
## Error: environment overflow, "setL2CacheWT" deleted
## Error: environment overflow, "disL2Prefetch" deleted
## Error: environment overflow, "enaICPref" deleted
## Error: environment overflow, "enaDCPref" deleted
## Error: environment overflow, "sata_dma_mode" deleted
## Error: environment overflow, "MALLOC_len" deleted
## Error: environment overflow, "ethprime" deleted
## Error: environment overflow, "netbsd_en" deleted
## Error: environment overflow, "vxworks_en" deleted
## Error: environment overflow, "bootargs_root" deleted
## Error: environment overflow, "bootargs_end" deleted
## Error: environment overflow, "image_name" deleted
## Error: environment overflow, "bootcmd" deleted
## Error: environment overflow, "standalone" deleted
## Error: environment overflow, "bootdelay" deleted
## Error: environment overflow, "disaMvPnp" deleted
## Error: environment overflow, "disaMvPnp" deleted
## Error: environment overflow, "ethaddr" deleted
## Error: environment overflow, "ethmtu" deleted
## Error: environment overflow, "eth1addr" deleted
## Error: environment overflow, "eth1mtu" deleted
## Error: environment overflow, "mvPhoneConfig" deleted
## Error: environment overflow, "mvNetConfig" deleted
## Error: environment overflow, "usb0Mode" deleted
## Error: environment overflow, "yuk_ethaddr" deleted
## Error: environment overflow, "nandEcc" deleted
## Error: environment overflow, "hddPowerCtrl" deleted
## Error: environment overflow, "netretry" deleted
## Error: environment overflow, "rcvrip" deleted
## Error: environment overflow, "loadaddr" deleted
## Error: environment overflow, "autoload" deleted
## Error: environment overflow, "enaAutoRecovery" deleted
  
Streaming disabled
Write allocate disabled
  
Module 0 is RGMII
Module 1 is TDM
  
USB 0: device mode
PEX 0: interface detected no Link.
Net:   ## Error: environment overflow, "ethact" deleted
egiga0, egiga1## Error: environment overflow, "ethact" deleted
  
USB:   scanning bus for devices... 1 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
Aquiring an IP address using DHCP...
## Error: environment overflow, "ethact" deleted
egiga0 no link
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
*** ERROR: `ethaddr' not set
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
egiga0 no link
## Error: environment overflow, "ethact" deleted
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
egiga0 no link
## Error: environment overflow, "ethact" deleted
*** ERROR: `eth1addr' not set
## Error: environment overflow, "ethact" deleted
egiga0 no link
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
## Error: environment overflow, "ethact" deleted
egiga0 no link
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
*** ERROR: `ethaddr' not set
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
egiga0 no link
## Error: environment overflow, "ethact" deleted
Failed to retreive an IP address assuming default (<NULL>)!
Starting the Recovery process to retreive the file...
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
egiga0 no link
## Error: environment overflow, "ethact" deleted
*** ERROR: `eth1addr' not set
## Error: environment overflow, "ethact" deleted
egiga0 no link
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
Failed
Power Button is pressed!
MPP Sel: 00000530, Data IN Enable: 00020058, Data In Polarity: 00000040, Data In: 00000010
Power Button is released!
MAC: 00:01:B8:4A:48:0B, IP: 10.74.72.11
## Error: environment overflow, "ethaddr" deleted
## Error: environment overflow, "ipaddr" deleted
## Error: environment overflow, "serverip" deleted
## Error: environment overflow, "netmask" deleted
## Error: environment overflow, "image_name" deleted
## Error: environment overflow, "console" deleted
## Error: environment overflow, "bootargs_root" deleted
## Error: environment overflow, "rootpath" deleted
## Error: environment overflow, "ethact" deleted
egiga0 no link
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
*** ERROR: `serverip' not set
## Error: environment overflow, "bootargs" deleted
## Booting image at 00800000 ...
Bad Magic Number

when entering setenv ipaddr I get the error environment overflow ipaddr deleted

I tried to boot from USB, doing it according to these instructions: https://forum.doozan.com/read.php?2,12096
using this u-boot to boot: uboot.2017.07-tld-1.netgear_ms2110.bodhi.tar

after loading I get this log:

U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:38:05 -0700)
Netgear Stora MS2110

SoC:   Kirkwood 88F6281_A0
DRAM:  128 MiB
WARNING: Caches not enabled
NAND:  256 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   egiga0
PHY reset timed out
88E1116 Initialized on egiga0
Hit any key to stop autoboot:  0 
starting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 
Use USB retry period from the environment: 15 second(s)
1 Storage Device(s) found

Reset IDE: ide_preinit failed

Partition Map for USB device 0  --   Partition Type: DOS

Part	Start Sector	Num Sectors	UUID		Type
  1	2048      	7829504   	135e42c5-01	83

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0
loading envs from usb 0 ...
** File not found /boot/uEnv.txt **

no IDE devices available
running scan_disk ...
Scan device usb
device usb 0:1
1 bytes read in 692 ms (0 Bytes/s)
Found bootable drive on usb 0
loading uImage ...
6235659 bytes read in 1155 ms (5.1 MiB/s)
loading uInitrd ...
EHCI timed out on TD - token=0xce008d80
EHCI timed out on TD - token=0xe008d80
5791271 bytes read in 12554 ms (450.2 KiB/s)
loading DTB /boot/dts/kirkwood-netgear_stora_ms2000 ...
** File not found /boot/dts/kirkwood-netgear_stora_ms2000 **
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-6.5.7-kirkwood-tld-1
   Created:      2025-02-09  18:02:18 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    6235595 Bytes = 5.9 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
   Image Name:   initramfs-6.5.7-kirkwood-tld-1
   Created:      2023-10-31  22:53:55 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    5791207 Bytes = 5.5 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
   Loading Ramdisk to 03a7a000, end 03fffde7 ... OK

Starting kernel ...

[    0.000000][    T0] Booting Linux on physical CPU 0x0
[    0.000000][    T0] Linux version 6.5.7-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #2 PREEMPT Wed Oct 18 21:14:11 PDT 2023
[    0.000000][    T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000][    T0] CPU: VIVT data cache, VIVT instruction cache
[    0.000000][    T0] OF: fdt: Machine model: NETGEAR MS2000 / MS2110 aka Stora
[    0.000000][    T0] Memory policy: Data cache writeback
[    0.000000][    T0] Zone ranges:
[    0.000000][    T0]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000][    T0] Movable zone start for each node
[    0.000000][    T0] Early memory node ranges
[    0.000000][    T0]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000][    T0] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000][    T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:1m(uboot),4m@1m(kernel),251m@5m(rootfs) rw
[    0.000000][    T0] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000][    T0] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000][    T0] Built 1 zonelists, mobility grouping on.  Total pages: 32480
[    0.000000][    T0] mem auto-init: stack:off, heap alloc:on, heap free:off
[    0.000000][    T0] Memory: 102520K/131072K available (12288K kernel code, 1755K rwdata, 5416K rodata, 1024K init, 301K bss, 28552K reserved, 0K cma-reserved)
[    0.000000][    T0] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000][    T0] trace event string verifier disabled
[    0.000000][    T0] rcu: Preemptible hierarchical RCU implementation.
[    0.000000][    T0] 	Trampoline variant of Tasks RCU enabled.
[    0.000000][    T0] 	Tracing variant of Tasks RCU enabled.
[    0.000000][    T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000][    T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000][    T0] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000][    T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[    0.000002][    T0] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[    0.000060][    T0] Switching to timer-based delay loop, resolution 5ns
[    0.000793][    T0] Console: colour dummy device 80x30
[    0.000884][    T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000)
[    0.000922][    T0] CPU: Testing write buffer coherency: ok
[    0.001088][    T0] pid_max: default: 32768 minimum: 301
[    0.011737][    T0] LSM: initializing lsm=capability,integrity
[    0.014622][    T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.014668][    T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.030052][    T1] RCU Tasks: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1.
[    0.030592][    T1] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1.
[    0.031209][    T1] Setting up static identity map for 0x100000 - 0x100058
[    0.031626][    T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2
[    0.032241][    T1] rcu: Hierarchical SRCU implementation.
[    0.032263][    T1] rcu: 	Max phase no-delay instances is 1000.
[    0.035928][    T1] devtmpfs: initialized
[    0.048466][    T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.048523][    T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.052086][    T1] prandom: seed boundary self test passed
[    0.057209][    T1] prandom: 100 self tests passed
[    0.057228][    T1] pinctrl core: initialized pinctrl subsystem
[    0.062837][    T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.064010][    T1] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.070582][    T1] audit: initializing netlink subsys (disabled)
[    0.073332][    T1] thermal_sys: Registered thermal governor 'step_wise'
[    0.073544][   T19] audit: type=2000 audit(0.070:1): state=initialized audit_enabled=0 res=1
[    0.073609][    T1] cpuidle: using governor ladder
[    0.073711][    T1] cpuidle: using governor menu
[    0.074534][    T1] Feroceon L2: Enabling L2
[    0.074582][    T1] Feroceon L2: Cache support initialised.
[    0.087568][    T1] No ATAGs?
[    0.450081][    T1] raid6: int32x8  gen()    91 MB/s
[    0.790075][    T1] raid6: int32x4  gen()    88 MB/s
[    1.130114][    T1] raid6: int32x2  gen()   113 MB/s
[    1.470075][    T1] raid6: int32x1  gen()    82 MB/s
[    1.470092][    T1] raid6: using algorithm int32x2 gen() 113 MB/s
[    1.810079][    T1] raid6: .... xor() 72 MB/s, rmw enabled
[    1.810096][    T1] raid6: using intx1 recovery algorithm
[    1.812175][    T1] SCSI subsystem initialized
[    1.813150][    T1] usbcore: registered new interface driver usbfs
[    1.813285][    T1] usbcore: registered new interface driver hub
[    1.813407][    T1] usbcore: registered new device driver usb
[    1.813839][    T1] pps_core: LinuxPPS API ver. 1 registered
[    1.813851][    T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    1.813891][    T1] PTP clock support registered
[    1.817288][    T1] vgaarb: loaded
[    1.830883][    T1] clocksource: Switched to clocksource orion_clocksource
[    1.842499][    T1] VFS: Disk quotas dquot_6.6.0
[    1.843025][    T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.882184][    T1] NET: Registered PF_INET protocol family
[    1.882557][    T1] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    1.884939][    T1] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    1.885234][    T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    1.885271][    T1] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    1.885312][    T1] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    1.885353][    T1] TCP: Hash tables configured (established 1024 bind 1024)
[    1.886203][    T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear)
[    1.886499][    T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    1.886542][    T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    1.887609][    T1] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    1.892053][    T1] RPC: Registered named UNIX socket transport module.
[    1.892071][    T1] RPC: Registered udp transport module.
[    1.892079][    T1] RPC: Registered tcp transport module.
[    1.892086][    T1] RPC: Registered tcp-with-tls transport module.
[    1.892094][    T1] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.892121][    T1] PCI: CLS 0 bytes, default 32
[    1.901503][   T32] Trying to unpack rootfs image as initramfs...
[    3.086787][   T32] Freeing initrd memory: 5656K
[    4.299770][    T1] Initialise system trusted keyrings
[    4.299902][    T1] Key type blacklist registered
[    4.301842][    T1] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[    4.302072][    T1] zbud: loaded
[    4.325155][    T1] NFS: Registering the id_resolver key type
[    4.325220][    T1] Key type id_resolver registered
[    4.325233][    T1] Key type id_legacy registered
[    4.325470][    T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    4.325497][    T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[    4.327414][    T1] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    4.328502][    T1] fuse: init (API version 7.38)
[    4.330277][    T1] orangefs_debugfs_init: called with debug mask: :none: :0:
[    4.330732][    T1] orangefs_init: module version upstream loaded
[    4.331262][    T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled
[    4.585844][    T1] xor: measuring software checksum speed
[    4.596630][    T1]    arm4regs        :   917 MB/sec
[    4.614356][    T1]    8regs           :   556 MB/sec
[    4.626846][    T1]    32regs          :   789 MB/sec
[    4.626858][    T1] xor: using function: arm4regs (917 MB/sec)
[    4.626878][    T1] async_tx: api initialized (async)
[    4.626898][    T1] Key type asymmetric registered
[    4.626908][    T1] Asymmetric key parser 'x509' registered
[    4.690376][    T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[    4.691038][    T1] io scheduler bfq registered
[    4.919167][    T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[    4.921642][    T1] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation.
[    4.923272][    T1] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation.
[    4.924514][    T1] mvebu-pcie mbus@f1000000:pcie@82000000: host bridge /mbus@f1000000/pcie@82000000 ranges:
[    4.924615][    T1] mvebu-pcie mbus@f1000000:pcie@82000000:      MEM 0x00f1040000..0x00f1041fff -> 0x0000040000
[    4.924670][    T1] mvebu-pcie mbus@f1000000:pcie@82000000:      MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[    4.924706][    T1] mvebu-pcie mbus@f1000000:pcie@82000000:       IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000
[    4.925783][    T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00
[    4.925809][    T1] pci_bus 0000:00: root bus resource [bus 00-ff]
[    4.925834][    T1] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff])
[    4.925854][    T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[    4.925872][    T1] pci_bus 0000:00: root bus resource [io  0x1000-0xeffff]
[    4.926013][    T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400
[    4.928126][    T1] PCI: bus0: Fast back to back transfers disabled
[    4.928161][    T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    4.928562][    T1] PCI: bus1: Fast back to back transfers enabled
[    4.928589][    T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    4.928641][    T1] pci 0000:00:01.0: PCI bridge to [bus 01]
[    4.929949][    T1] mv_xor f1060800.xor: Marvell shared XOR driver
[    4.994098][    T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    4.999860][    T1] mv_xor f1060900.xor: Marvell shared XOR driver
[    5.064099][    T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    5.070224][    T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    5.073685][    T1] printk: console [ttyS0] disabled
[    5.074506][    T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 28, base_baud = 12500000) is a 16550A
[    5.074587][    T1] printk: console [ttyS0] enabled
[    6.077123][    T1] loop: module loaded
[    6.082363][    T1] sata_mv f1080000.sata: slots 32 ports 2
[    6.094068][    T1] scsi host0: sata_mv
[    6.099903][    T1] scsi host1: sata_mv
[    6.104443][    T1] ata1: SATA max UDMA/133 irq 29
[    6.109280][    T1] ata2: SATA max UDMA/133 irq 29
[    6.115912][    T1] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xda
[    6.123064][    T1] nand: Samsung NAND 256MiB 3,3V 8-bit
[    6.128409][    T1] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    6.136779][    T1] Scanning device for bad blocks
[    6.328820][    T1] Bad eraseblock 1736 at 0x00000d900000
[    6.367953][    T1] 3 cmdlinepart partitions found on MTD device orion_nand
[    6.375013][    T1] Creating 3 MTD partitions on "orion_nand":
[    6.380944][    T1] 0x000000000000-0x000000100000 : "uboot"
[    6.387643][    T1] 0x000000100000-0x000000500000 : "kernel"
[    6.394351][    T1] 0x000000500000-0x000010000000 : "rootfs"
[    6.403487][    T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[    6.412159][    T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[    6.428241][    T1] [Firmware Warn]: /ocp@f1000000/mdio-bus@72004/ethernet-phy@8: Whitelisted compatible string. Please remove
[    6.444963][   T53] ata1: SATA link down (SStatus 0 SControl F300)
[    6.474235][    T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    6.802637][   T55] ata2: SATA link down (SStatus 0 SControl F300)
[    7.242515][    T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 52:3b:20:9c:11:51
[    7.252845][    T1] orion-ehci f1050000.ehci: EHCI Host Controller
[    7.259121][    T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[    7.267882][    T1] orion-ehci f1050000.ehci: irq 32, io mem 0xf1050000
[    7.300925][    T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[    7.308166][    T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.05
[    7.317229][    T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    7.325223][    T1] usb usb1: Product: EHCI Host Controller
[    7.330839][    T1] usb usb1: Manufacturer: Linux 6.5.7-kirkwood-tld-1 ehci_hcd
[    7.338214][    T1] usb usb1: SerialNumber: f1050000.ehci
[    7.344938][    T1] hub 1-0:1.0: USB hub found
[    7.349475][    T1] hub 1-0:1.0: 1 port detected
[    7.355482][    T1] usbcore: registered new interface driver usb-storage
[    7.363029][    T1] mousedev: PS/2 mouse device common for all mice
[    7.640931][   T50] usb 1-1: new high-speed USB device number 2 using orion-ehci
[    7.842013][   T50] usb 1-1: New USB device found, idVendor=18a5, idProduct=0302, bcdDevice= 1.00
[    7.851001][   T50] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    7.858918][   T50] usb 1-1: Product: STORE N GO                    
[    7.865340][   T50] usb 1-1: Manufacturer: Verbatim                      
[    7.872214][   T50] usb 1-1: SerialNumber: 10J223000000411D
[    7.879066][   T50] usb-storage 1-1:1.0: USB Mass Storage device detected
[    7.887147][   T50] scsi host2: usb-storage 1-1:1.0
[    8.400938][    T1] rtc-mv f1010300.rtc: internal RTC not ticking
[    8.407475][    T1] i2c_dev: i2c /dev entries driver
[    8.417108][    T1] rtc-pcf8563 0-0051: registered as rtc0
[    8.424006][    T1] rtc-pcf8563 0-0051: setting system clock to 2025-02-10T18:19:48 UTC (1739211588)
[    8.435932][    T1] device-mapper: uevent: version 1.0.3
[    8.442106][    T1] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com
[    8.452125][    T1] device-mapper: multipath round-robin: version 1.2.0 loaded
[    8.459402][    T1] device-mapper: multipath queue-length: version 0.2.0 loaded
[    8.466850][    T1] device-mapper: multipath service-time: version 0.3.0 loaded
[    8.474335][    T1] device-mapper: dm-log-userspace: version 1.3.0 loaded
[    8.484819][    T1] ledtrig-cpu: registered to indicate activity on CPUs
[    8.491871][    T1] hid: raw HID events driver (C) Jiri Kosina
[    8.498322][    T1] drop_monitor: Initializing network drop monitor service
[    8.507301][    T1] NET: Registered PF_INET6 protocol family
[    8.515675][    T1] Segment Routing with IPv6
[    8.520082][    T1] RPL Segment Routing with IPv6
[    8.525047][    T1] In-situ OAM (IOAM) with IPv6
[    8.529916][    T1] NET: Registered PF_PACKET protocol family
[    8.536205][    T1] Key type dns_resolver registered
[    8.564766][    T1] registered taskstats version 1
[    8.569897][    T1] Loading compiled-in X.509 certificates
[    8.602396][    T1] Key type .fscrypt registered
[    8.607065][    T1] Key type fscrypt-provisioning registered
[    8.620813][    T1] Key type big_key registered
[    8.682101][    T1] Key type encrypted registered
[    8.818820][  T107] "cryptomgr_test" (107) uses obsolete ecb(arc4) skcipher
[    8.961990][   T18] scsi 2:0:0:0: Direct-Access     Verbatim STORE N GO       1.00 PQ: 0 ANSI: 2
[    8.983446][   T32] sd 2:0:0:0: [sda] 7831552 512-byte logical blocks: (4.01 GB/3.73 GiB)
[    9.001680][   T32] sd 2:0:0:0: [sda] Write Protect is off
[    9.020944][   T32] sd 2:0:0:0: [sda] No Caching mode page found
[    9.027008][   T32] sd 2:0:0:0: [sda] Assuming drive cache: write through
[    9.047460][   T32]  sda: sda1
[    9.061275][   T32] sd 2:0:0:0: [sda] Attached SCSI removable disk
[   11.633319][    T1] clk: Disabling unused clocks
[   11.642627][    T1] Freeing unused kernel image (initmem) memory: 1024K
[   11.661987][    T1] Checked W+X mappings: passed, no W+X pages found
[   11.668410][    T1] Run /init as init process
Loading, please wait...
Starting systemd-udevd version 252.17-1~deb12u1
[   13.437877][  T157] usbcore: registered new interface driver uas
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Waiting for root file system ... Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
done.
Gave up waiting for root file system device.  Common problems:
 - Boot args (cat /proc/cmdline)
   - Check rootdelay= (did the system wait long enough?)
 - Missing modules (cat /proc/modules; ls /dev)
ALERT!  LABEL=rootfs does not exist.  Dropping to a shell!


BusyBox v1.35.0 (Debian 1:1.35.0-4+b3) built-in shell (ash)
Enter 'help' for a list of built-in commands.

(initramfs) [   75.930948][    C0] random: crng init done

Guys, please help me, I don't know what to do