Hi all
This could be the same problem I'm experiencing: https://forum.doozan.com/read.php?2,110769
For context, after much support from our host a few years ago, I got Debian running stable with 2x SATA HDDs, and that ran without any issues for years. A couple of weeks ago I figured I'd update the kernel from 5.4.2 (!) to 6.12.6.
At that point I started getting boot failures, as long as any SATA HDD was connected, see logs below.
It looks like the USB root device (seen as /dev/sdc) briefly goes offline during the boot process and is reconnected almost immeditely, but as /dev/sdd. So the boot process does not find the filesystem anymore and fails with I/O errors.
To help debugging I grabbed another pen drive which also used to work, and created a fresh new rootfs with 6.5.7. That rootfs is untouched and fails out of the box in almost the same way: I can get to aroot login prompt, but after a couple of minutes (at most), the same thing happens. The root device /dev/sdc disappears and reappears as /dev/sdd, so all I/O accesses fail.
Both pendrives work correctly when there are no SATA HDDs attached to the device.
U-Boot envs:
And boot log:
This could be the same problem I'm experiencing: https://forum.doozan.com/read.php?2,110769
For context, after much support from our host a few years ago, I got Debian running stable with 2x SATA HDDs, and that ran without any issues for years. A couple of weeks ago I figured I'd update the kernel from 5.4.2 (!) to 6.12.6.
At that point I started getting boot failures, as long as any SATA HDD was connected, see logs below.
It looks like the USB root device (seen as /dev/sdc) briefly goes offline during the boot process and is reconnected almost immeditely, but as /dev/sdd. So the boot process does not find the filesystem anymore and fails with I/O errors.
To help debugging I grabbed another pen drive which also used to work, and created a fresh new rootfs with 6.5.7. That rootfs is untouched and fails out of the box in almost the same way: I can get to aroot login prompt, but after a couple of minutes (at most), the same thing happens. The root device /dev/sdc disappears and reappears as /dev/sdd, so all I/O accesses fail.
Both pendrives work correctly when there are no SATA HDDs attached to the device.
U-Boot envs:
NSA3x0S> printenv arcNumber=4931 baudrate=115200 bootargs=console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; reset bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm$load_uimage_addr; fi; fi bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi bootdelay=10 bootdev=usb console=ttyS0,115200 device=0:1 devices=usb disks=0 1 2 3 dtb_file=/boot/dts/kirkwood-nsa320s.dtb ethact=egiga0 ethaddr=XX:XX:XX:XX:XX:XX fileaddr=800000 filesize=5ef848 if_netconsole=ping $serverip ipaddr=192.168.0.231 led_error=orange blinking led_exit=green off led_init=green blinking load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file load_dtb_addr=0x2c00000 load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd load_initrd_addr=0x1100000 load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage load_uimage_addr=0x800000 mainlineLinux=yes mtdids=nand0=orion_nand mtdparts=mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) partition=nand0,2 poke=mw.l f1010104 c70f0ffd preboot_nc=run if_netconsole start_netconsole scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start"; setenv scan_ide "ide reset"; setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done serverip=192.168.0.220 set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version; stderr=serial stdin=serial stdout=serial uenv_addr=0x810000 uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize uenv_init_devices=setenv init_usb "usb start"; setenv init_ide "ide reset"; setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done; uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices; do for disknum in 0; do run uenv_read_disk; done; done; uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read; fi; else if $devtype part $disknum; then run uenv_read; fi; fi Environment size: 3297/131068 bytes
And boot log:
U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:50:06 -0700) ZyXEL NSA310S/320S 1/2-Bay Power Media Server SoC: Kirkwood 88F6702_A1 DRAM: 256 MiB WARNING: Caches not enabled NAND: 128 MiB In: serial Out: serial Err: serial Net: egiga0 MV88E1318 PHY initialized on egiga0 Hit any key to stop autoboot: 0 NSA3x0S> printenv poke; run poke; ide reset; sleep 60; usb start; boot poke=mw.l f1010104 c70f0ffd Reset IDE: Bus 0: OK Bus 1: .........OK Device 0: Model: WDC WD30EFRX-68EUZN0 Firm: 82.00A82 Ser#: WD-WCC4N6FC8VSV Type: Hard Disk Supports 48-bit addressing Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512) Device 1: Model: WDC WD30EFRX-68EUZN0 Firm: 82.00A82 Ser#: WD-WCC4N6JN55AL Type: Hard Disk Supports 48-bit addressing Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512) starting USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 3 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Partition Map for USB device 0 -- Partition Type: DOS Part Start Sector Num Sectors UUID Type 1 2048 3905536 06b4319f-01 83 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 ## Unknown partition table type 0 loading envs from usb 0 ... ** File not found /boot/uEnv.txt ** running scan_disk ... Scan device usb device usb 0:1 1 bytes read in 661 ms (0 Bytes/s) Found bootable drive on usb 0 loading uImage ... 6223944 bytes read in 1058 ms (5.6 MiB/s) loading uInitrd ... 5791271 bytes read in 947 ms (5.8 MiB/s) loading DTB /boot/dts/kirkwood-nsa320s.dtb ... 12802 bytes read in 1799 ms (6.8 KiB/s) ## Booting kernel from Legacy Image at 00800000 ... Image Name: Linux-6.5.7-kirkwood-tld-1 Created: 2023-10-31 22:53:22 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 6223880 Bytes = 5.9 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 01100000 ... Image Name: initramfs-6.5.7-kirkwood-tld-1 Created: 2023-10-31 22:53:55 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 5791207 Bytes = 5.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 02c00000 Booting using the fdt blob at 0x2c00000 Loading Kernel Image ... OK Loading Ramdisk to 0f585000, end 0fb0ade7 ... OK Loading Device Tree to 0f57e000, end 0f584201 ... OK Starting kernel ... [ 0.000000][ T0] Booting Linux on physical CPU 0x0 [ 0.000000][ T0] Linux version 6.5.7-kirkwood-tld-1 (root@tldDebian) (gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #2 PREEMPT Wed Oct 18 21:14:11 PDT 2023 [ 0.000000][ T0] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f [ 0.000000][ T0] CPU: VIVT data cache, VIVT instruction cache [ 0.000000][ T0] OF: fdt: Machine model: Zyxel NSA320S [ 0.000000][ T0] Memory policy: Data cache writeback [ 0.000000][ T0] Zone ranges: [ 0.000000][ T0] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Movable zone start for each node [ 0.000000][ T0] Early memory node ranges [ 0.000000][ T0] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000][ T0] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) [ 0.000000][ T0] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000][ T0] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000][ T0] Built 1 zonelists, mobility grouping on. Total pages: 64960 [ 0.000000][ T0] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000][ T0] Memory: 232336K/262144K available (12288K kernel code, 1755K rwdata, 5416K rodata, 1024K init, 301K bss, 29808K reserved, 0K cma-reserved) [ 0.000000][ T0] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000][ T0] trace event string verifier disabled [ 0.000000][ T0] rcu: Preemptible hierarchical RCU implementation. [ 0.000000][ T0] Trampoline variant of Tasks RCU enabled. [ 0.000000][ T0] Tracing variant of Tasks RCU enabled. [ 0.000000][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000][ T0] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000][ T0] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000][ T0] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns [ 0.000002][ T0] sched_clock: 32 bits at 167MHz, resolution 6ns, wraps every 12884901885ns [ 0.000056][ T0] Switching to timer-based delay loop, resolution 6ns [ 0.000738][ T0] Console: colour dummy device 80x30 [ 0.000819][ T0] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666) [ 0.000854][ T0] CPU: Testing write buffer coherency: ok [ 0.001006][ T0] pid_max: default: 32768 minimum: 301 [ 0.011516][ T0] LSM: initializing lsm=capability,integrity [ 0.014374][ T0] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.014415][ T0] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.028919][ T1] RCU Tasks: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1. [ 0.029331][ T1] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1. [ 0.029860][ T1] Setting up static identity map for 0x100000 - 0x100058 [ 0.030330][ T1] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3 [ 0.030812][ T1] rcu: Hierarchical SRCU implementation. [ 0.030830][ T1] rcu: Max phase no-delay instances is 1000. [ 0.034300][ T1] devtmpfs: initialized [ 0.047022][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.047074][ T1] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.050636][ T1] prandom: seed boundary self test passed [ 0.055756][ T1] prandom: 100 self tests passed [ 0.055773][ T1] pinctrl core: initialized pinctrl subsystem [ 0.060878][ T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.061831][ T1] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.068196][ T1] audit: initializing netlink subsys (disabled) [ 0.070642][ T1] thermal_sys: Registered thermal governor 'step_wise' [ 0.070827][ T19] audit: type=2000 audit(0.060:1): state=initialized audit_enabled=0 res=1 [ 0.070885][ T1] cpuidle: using governor ladder [ 0.070976][ T1] cpuidle: using governor menu [ 0.071732][ T1] Feroceon L2: Enabling L2 [ 0.071772][ T1] Feroceon L2: Cache support initialised. [ 0.084961][ T1] No ATAGs? [ 0.450075][ T1] raid6: int32x8 gen() 93 MB/s [ 0.790070][ T1] raid6: int32x4 gen() 92 MB/s [ 1.130103][ T1] raid6: int32x2 gen() 120 MB/s [ 1.470070][ T1] raid6: int32x1 gen() 93 MB/s [ 1.470084][ T1] raid6: using algorithm int32x2 gen() 120 MB/s [ 1.810072][ T1] raid6: .... xor() 76 MB/s, rmw enabled [ 1.810086][ T1] raid6: using intx1 recovery algorithm [ 1.812009][ T1] SCSI subsystem initialized [ 1.812884][ T1] usbcore: registered new interface driver usbfs [ 1.812964][ T1] usbcore: registered new interface driver hub [ 1.813038][ T1] usbcore: registered new device driver usb [ 1.813466][ T1] pps_core: LinuxPPS API ver. 1 registered [ 1.813477][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 1.813514][ T1] PTP clock support registered [ 1.816708][ T1] vgaarb: loaded [ 1.817663][ T1] clocksource: Switched to clocksource orion_clocksource [ 1.836525][ T1] VFS: Disk quotas dquot_6.6.0 [ 1.837039][ T1] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.876012][ T1] NET: Registered PF_INET protocol family [ 1.876363][ T1] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 1.878969][ T1] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 1.879188][ T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 1.879223][ T1] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 1.879272][ T1] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 1.879328][ T1] TCP: Hash tables configured (established 2048 bind 2048) [ 1.880126][ T1] MPTCP token hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.880409][ T1] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 1.880448][ T1] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 1.881479][ T1] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 1.888748][ T1] RPC: Registered named UNIX socket transport module. [ 1.888765][ T1] RPC: Registered udp transport module. [ 1.888772][ T1] RPC: Registered tcp transport module. [ 1.888779][ T1] RPC: Registered tcp-with-tls transport module. [ 1.888786][ T1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.888810][ T1] PCI: CLS 0 bytes, default 32 [ 1.892153][ T32] Trying to unpack rootfs image as initramfs... [ 3.017073][ T32] Freeing initrd memory: 5656K [ 4.242602][ T1] Initialise system trusted keyrings [ 4.242708][ T1] Key type blacklist registered [ 4.244298][ T1] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 4.244500][ T1] zbud: loaded [ 4.267312][ T1] NFS: Registering the id_resolver key type [ 4.267407][ T1] Key type id_resolver registered [ 4.267418][ T1] Key type id_legacy registered [ 4.267647][ T1] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 4.267753][ T1] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 4.269646][ T1] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 4.270648][ T1] fuse: init (API version 7.38) [ 4.272379][ T1] orangefs_debugfs_init: called with debug mask: :none: :0: [ 4.272717][ T1] orangefs_init: module version upstream loaded [ 4.273190][ T1] SGI XFS with ACLs, security attributes, realtime, scrub, quota, no debug enabled [ 4.527283][ T1] xor: measuring software checksum speed [ 4.537966][ T1] arm4regs : 927 MB/sec [ 4.555666][ T1] 8regs : 556 MB/sec [ 4.568169][ T1] 32regs : 789 MB/sec [ 4.568180][ T1] xor: using function: arm4regs (927 MB/sec) [ 4.568198][ T1] async_tx: api initialized (async) [ 4.568215][ T1] Key type asymmetric registered [ 4.568225][ T1] Asymmetric key parser 'x509' registered [ 4.627095][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 4.627619][ T1] io scheduler bfq registered [ 4.854905][ T1] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver [ 4.857192][ T1] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 4.858972][ T1] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation. [ 4.860213][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: host bridge /mbus@f1000000/pcie@82000000 ranges: [ 4.860308][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0x00f1040000..0x00f1041fff -> 0x0000040000 [ 4.860361][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: MEM 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 4.860395][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: IO 0xffffffffffffffff..0x00fffffffe -> 0x0100000000 [ 4.861199][ T1] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00 [ 4.861221][ T1] pci_bus 0000:00: root bus resource [bus 00-ff] [ 4.861244][ T1] pci_bus 0000:00: root bus resource [mem 0xf1040000-0xf1041fff] (bus address [0x00040000-0x00041fff]) [ 4.861263][ T1] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff] [ 4.861281][ T1] pci_bus 0000:00: root bus resource [io 0x1000-0xeffff] [ 4.861414][ T1] pci 0000:00:01.0: [11ab:6281] type 01 class 0x060400 [ 4.863638][ T1] PCI: bus0: Fast back to back transfers disabled [ 4.863672][ T1] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 4.864006][ T1] PCI: bus1: Fast back to back transfers enabled [ 4.864032][ T1] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 4.864081][ T1] pci 0000:00:01.0: PCI bridge to [bus 01] [ 4.865304][ T1] mv_xor f1060800.xor: Marvell shared XOR driver [ 4.930798][ T1] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 4.936341][ T1] mv_xor f1060900.xor: Marvell shared XOR driver [ 5.000811][ T1] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr ) [ 5.006719][ T1] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 5.009846][ T1] printk: console [ttyS0] disabled [ 5.010612][ T1] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 28, base_baud = 10416666) is a 16550A [ 5.010687][ T1] printk: console [ttyS0] enabled [ 6.011843][ T1] loop: module loaded [ 6.016938][ T1] sata_mv f1080000.sata: slots 32 ports 2 [ 6.027895][ T1] scsi host0: sata_mv [ 6.033579][ T1] scsi host1: sata_mv [ 6.037979][ T1] ata1: SATA max UDMA/133 irq 29 [ 6.042767][ T1] ata2: SATA max UDMA/133 irq 29 [ 6.049223][ T1] nand: device found, Manufacturer ID: 0x92, Chip ID: 0xf1 [ 6.056262][ T1] nand: Eon NAND 128MiB 3,3V 8-bit [ 6.061256][ T1] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 6.069548][ T1] Scanning device for bad blocks [ 6.079488][ T1] Bad eraseblock 100 at 0x000000c80000 [ 6.089893][ T1] Bad eraseblock 200 at 0x000001900000 [ 6.137247][ T1] 9 cmdlinepart partitions found on MTD device orion_nand [ 6.144212][ T1] Creating 9 MTD partitions on "orion_nand": [ 6.150056][ T1] 0x000000000000-0x000000100000 : "uboot" [ 6.156591][ T1] 0x000000100000-0x000000180000 : "stock_uboot_env" [ 6.163884][ T1] 0x000000180000-0x000000200000 : "key_store" [ 6.170686][ T1] 0x000000200000-0x000000280000 : "info" [ 6.177000][ T1] 0x000000280000-0x000000c80000 : "etc" [ 6.183330][ T1] 0x000000c80000-0x000001680000 : "kernel_1" [ 6.190085][ T1] 0x000001680000-0x000004640000 : "rootfs1" [ 6.196888][ T1] 0x000004640000-0x000005040000 : "kernel_2" [ 6.203702][ T1] 0x000005040000-0x000008000000 : "rootfs2" [ 6.211610][ T1] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 6.220159][ T1] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 6.235639][ T1] [Firmware Warn]: /ocp@f1000000/mdio-bus@72004/ethernet-phy@1: Whitelisted compatible string. Please remove [ 6.272622][ T1] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 [ 6.282693][ T1] mv643xx_eth: Set the PHY to fix link down [ 6.283842][ T1] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 52:3b:20:9c:11:51 [ 6.299877][ T1] orion-ehci f1050000.ehci: EHCI Host Controller [ 6.306132][ T1] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1 [ 6.314784][ T1] orion-ehci f1050000.ehci: irq 32, io mem 0xf1050000 [ 6.347692][ T1] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00 [ 6.354928][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.05 [ 6.363923][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.371867][ T1] usb usb1: Product: EHCI Host Controller [ 6.377461][ T1] usb usb1: Manufacturer: Linux 6.5.7-kirkwood-tld-1 ehci_hcd [ 6.384846][ T1] usb usb1: SerialNumber: f1050000.ehci [ 6.391524][ T1] hub 1-0:1.0: USB hub found [ 6.396014][ T1] hub 1-0:1.0: 1 port detected [ 6.401906][ T1] usbcore: registered new interface driver usb-storage [ 6.409313][ T1] mousedev: PS/2 mouse device common for all mice [ 6.416077][ T1] i2c_dev: i2c /dev entries driver [ 6.424461][ T1] ht1382 0-0068: registered as rtc0 [ 6.430824][ T1] ht1382 0-0068: setting system clock to 2025-02-23T13:14:57 UTC (1740316497) [ 6.441274][ T1] device-mapper: uevent: version 1.0.3 [ 6.447225][ T1] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com [ 6.457247][ T1] device-mapper: multipath round-robin: version 1.2.0 loaded [ 6.464543][ T1] device-mapper: multipath queue-length: version 0.2.0 loaded [ 6.471864][ T1] device-mapper: multipath service-time: version 0.3.0 loaded [ 6.479250][ T1] device-mapper: dm-log-userspace: version 1.3.0 loaded [ 6.489933][ T1] ledtrig-cpu: registered to indicate activity on CPUs [ 6.496801][ T1] hid: raw HID events driver (C) Jiri Kosina [ 6.503186][ T1] drop_monitor: Initializing network drop monitor service [ 6.512035][ T1] NET: Registered PF_INET6 protocol family [ 6.520269][ T1] Segment Routing with IPv6 [ 6.524628][ T1] RPL Segment Routing with IPv6 [ 6.529524][ T1] In-situ OAM (IOAM) with IPv6 [ 6.534268][ T1] NET: Registered PF_PACKET protocol family [ 6.540660][ T1] Key type dns_resolver registered [ 6.547759][ T53] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 6.557220][ T53] ata1.00: ATA-9: WDC WD30EFRX-68EUZN0, 82.00A82, max UDMA/133 [ 6.577819][ T53] ata1.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 6.588042][ T53] ata1.00: configured for UDMA/133 [ 6.596299][ T1] registered taskstats version 1 [ 6.601465][ T1] Loading compiled-in X.509 certificates [ 6.607544][ T10] scsi 0:0:0:0: Direct-Access ATA WDC WD30EFRX-68E 0A82 PQ: 0 ANSI: 5 [ 6.629668][ T32] sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB) [ 6.647779][ T32] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 6.653815][ T32] sd 0:0:0:0: [sda] Write Protect is off [ 6.664290][ T32] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 6.675098][ T1] Key type .fscrypt registered [ 6.679760][ T1] Key type fscrypt-provisioning registered [ 6.686120][ T32] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 6.693152][ T50] usb 1-1: new high-speed USB device number 2 using orion-ehci [ 6.707962][ T1] Key type big_key registered [ 6.764534][ T32] sda: [ 6.767455][ T32] sd 0:0:0:0: [sda] Attached SCSI disk [ 6.777413][ T1] Key type encrypted registered [ 6.899669][ T50] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=85.32 [ 6.913758][ T50] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 6.922141][ T104] "cryptomgr_test" (104) uses obsolete ecb(arc4) skcipher [ 6.929191][ T50] usb 1-1: Product: USB2.0 Hub [ 6.938676][ T50] hub 1-1:1.0: USB hub found [ 6.948171][ T50] hub 1-1:1.0: 4 ports detected [ 7.137709][ T55] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 7.157870][ T55] ata2.00: ATA-9: WDC WD30EFRX-68EUZN0, 82.00A82, max UDMA/133 [ 7.165253][ T55] ata2.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 7.190308][ T55] ata2.00: configured for UDMA/133 [ 7.216044][ T18] scsi 1:0:0:0: Direct-Access ATA WDC WD30EFRX-68E 0A82 PQ: 0 ANSI: 5 [ 7.239497][ T32] sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB) [ 7.257713][ T32] sd 1:0:0:0: [sdb] 4096-byte physical blocks [ 7.263711][ T32] sd 1:0:0:0: [sdb] Write Protect is off [ 7.277711][ T50] usb 1-1.1: new high-speed USB device number 3 using orion-ehci [ 7.285498][ T32] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 7.307828][ T32] sd 1:0:0:0: [sdb] Preferred minimum I/O size 4096 bytes [ 7.360075][ T32] sdb: sdb1 sdb2 sdb3 [ 7.369231][ T32] sd 1:0:0:0: [sdb] Attached SCSI disk [ 7.519539][ T50] usb 1-1.1: New USB device found, idVendor=0951, idProduct=1665, bcdDevice= 2.00 [ 7.537687][ T50] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7.545669][ T50] usb 1-1.1: Product: DataTraveler 2.0 [ 7.567684][ T50] usb 1-1.1: Manufacturer: Kingston [ 7.572730][ T50] usb 1-1.1: SerialNumber: 0017318974D91FC0693A4974 [ 7.589339][ T50] usb-storage 1-1.1:1.0: USB Mass Storage device detected [ 7.608408][ T50] scsi host2: usb-storage 1-1.1:1.0 [ 8.649884][ T32] scsi 2:0:0:0: Direct-Access Kingston DataTraveler 2.0 0000 PQ: 0 ANSI: 4 [ 8.670959][ T18] sd 2:0:0:0: [sdc] 30273600 512-byte logical blocks: (15.5 GB/14.4 GiB) [ 8.689578][ T18] sd 2:0:0:0: [sdc] Write Protect is off [ 8.707702][ T18] sd 2:0:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 8.737932][ T18] sdc: sdc1 [ 8.748005][ T18] sd 2:0:0:0: [sdc] Attached SCSI removable disk [ 9.898232][ T18] kirkwood-pinctrl f1010000.pin-controller: unsupported function gpio on pin mpp33 [ 9.907357][ T18] pinctrl core: failed to register map default (0): invalid type given [ 9.916351][ T1] clk: Disabling unused clocks [ 9.924524][ T1] Freeing unused kernel image (initmem) memory: 1024K [ 9.948656][ T1] Checked W+X mappings: passed, no W+X pages found [ 9.955013][ T1] Run /init as init process Loading, please wait... Starting systemd-udevd version 252.17-1~deb12u1 [ 11.723794][ T155] usbcore: registered new interface driver uas [ 13.047716][ T121] usb 1-1.1: reset high-speed USB device number 3 using orion-ehci [ 13.203860][ T121] sd 2:0:0:0: [sdc] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK cmd_age=1s [ 13.213808][ T121] sd 2:0:0:0: [sdc] tag#0 CDB: Read(10) 28 00 00 00 02 08 00 00 f0 00 [ 13.221829][ T121] I/O error, dev sdc, sector 520 op 0x0:(READ) flags 0x84700 phys_seg 2 prio class 2 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... done. Begin: Will now check root file system ... fsck from util-linux 2.38.1 [/sbin/fsck.ext3 (1) -- /dev/sdc1] fsck.ext3 -a -C0 /dev/sdc1 rootfs: recovering journal [ 38.781671][ T121] random: crng init done rootfs: Clearing orphaned inode 43428 (uid=0, gid=0, mode=0100644, size=313264) rootfs: clean, 20075/122160 files, 218978/488192 blocks done. [ 72.888984][ T180] EXT4-fs (sdc1): mounting ext3 file system using the ext4 subsystem [ 72.935344][ T180] EXT4-fs (sdc1): mounted filesystem bcf22700-38c8-477c-9969-e26f648c6e27 ro with ordered data mode. Quota mode: none. done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done. INIT: version 3.06 booting INIT: No inittab.d directory found Using makefile-style concurrent boot in runlevel S. Setting hostname to 'debian'...done. Starting hotplug events dispatcher: systemd-udevd. Synthesizing the initial hotplug events (subsystems)...done. Synthesizing the initial hotplug events (devices)...done. Waiting for /dev to be fully populated...[ 76.570955][ T359] input: gpio_keys as /devices/platform/gpio_keys/input/input0 [ 77.130978][ T358] orion_wdt: Initial timeout 25 sec [ 77.512515][ T361] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 77.671161][ T361] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 77.776786][ T361] sd 2:0:0:0: Attached scsi generic sg2 type 0 [ 77.898282][ T360] marvell-cesa f1030000.crypto: CESA device successfully registered [ 78.236835][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.279851][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.316854][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.359826][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.396826][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.407815][ T121] usb 1-1-port1: Cannot enable. Maybe the USB cable is bad? [ 78.460829][ T121] usb 1-1-port1: cannot disable (err = -71) [ 78.497821][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.534822][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.577863][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.613825][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.659830][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.665416][ T121] usb 1-1-port1: Cannot enable. Maybe the USB cable is bad? [ 78.719838][ T121] usb 1-1-port1: cannot disable (err = -71) [ 78.756838][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.797889][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.834850][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.879847][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.915838][ T121] usb 1-1-port1: cannot reset (err = -71) [ 78.927807][ T121] usb 1-1-port1: Cannot enable. Maybe the USB cable is bad? [ 78.967840][ T121] usb 1-1-port1: cannot disable (err = -71) [ 79.004849][ T121] usb 1-1-port1: cannot reset (err = -71) [ 79.049837][ T121] usb 1-1-port1: cannot reset (err = -71) [ 79.086826][ T121] usb 1-1-port1: cannot reset (err = -71) [ 79.129832][ T121] usb 1-1-port1: cannot reset (err = -71) [ 79.166834][ T121] usb 1-1-port1: cannot reset (err = -71) [ 79.177827][ T121] usb 1-1-port1: Cannot enable. Maybe the USB cable is bad? [ 79.217842][ T121] usb 1-1-port1: cannot disable (err = -71) [ 79.254830][ T121] usb 1-1-port1: cannot disable (err = -71) [ 79.267879][ T121] sd 2:0:0:0: [sdc] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK cmd_age=1s [ 79.284900][ T121] sd 2:0:0:0: [sdc] tag#0 CDB: Read(10) 28 00 01 cd f0 3a 00 00 01 00 [ 79.307726][ T121] I/O error, dev sdc, sector 30273594 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 79.323844][ T50] hub 1-1:1.0: hub_ext_port_status failed (err = -71) [ 79.517849][ T121] sd 2:0:0:0: [sdc] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK cmd_age=0s [ 79.536622][ T121] sd 2:0:0:0: [sdc] tag#0 CDB: Read(10) 28 00 01 cd f0 38 00 00 01 00 [ 79.557732][ T121] I/O error, dev sdc, sector 30273592 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 79.567126][ T121] Buffer I/O error on dev sdc, logical block 3784199, async page read [ 79.847870][ T365] sdc: detected capacity change from 30273600 to 0 [ 79.898172][ T364] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 79.904800][ T364] I/O error, dev sdc, sector 1922696 op 0x0:(READ) flags 0x80700 phys_seg 17 prio class 2 [ 80.077916][ T33] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.084544][ T33] I/O error, dev sdc, sector 1922768 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 [ 80.094073][ T33] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.100717][ T33] I/O error, dev sdc, sector 1922768 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 done. [ 80.587863][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.594485][ T199] I/O error, dev sdc, sector 2497840 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 80.607879][ T33] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.614504][ T33] I/O error, dev sdc, sector 2497840 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 mountdevsubfs.sh: Input/output e[ 80.627880][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device rror [ 80.635084][ T199] I/O error, dev sdc, sector 1994488 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 2 [ 80.647087][ T33] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.653858][ T33] I/O error, dev sdc, sector 1994488 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2 checkroot.sh: Input/output error[ 80.665626][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.673555][ T199] I/O error, dev sdc, sector 1994432 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2 [ 80.685121][ T33] sd 2:0:0:0: [sdc] tag#0 access beyond end of device checkfs.sh: Input/output error [ 80.694213][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.705410][ T435] sd 2:0:0:0: [sdc] tag#0 access beyond end of device checkroot-bootclean.sh: Input/ou[ 80.715976][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device tput error [ 80.726181][ T436] sd 2:0:0:0: [sdc] tag#0 access beyond end of device kmod: Input/output error [ 80.736790][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.746505][ T437] sd 2:0:0:0: [sdc] tag#0 access beyond end of device mount-configfs: Input/output err[ 80.757212][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device or [ 80.767362][ T438] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.778155][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.788231][ T439] sd 2:0:0:0: [sdc] tag#0 access beyond end of device mountall-bootclean.sh: Input/out[ 80.798889][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device put error [ 80.808918][ T440] sd 2:0:0:0: [sdc] tag#0 access beyond end of device brightness: Input/output error [ 80.819625][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.829564][ T441] sd 2:0:0:0: [sdc] tag#0 access beyond end of device procps: Input/output error [ 80.840226][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.850037][ T442] sd 2:0:0:0: [sdc] tag#0 access beyond end of device urandom: Input/output error [ 80.860761][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.870607][ T443] sd 2:0:0:0: [sdc] tag#0 access beyond end of device networking: Input/output error [ 80.881618][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.891887][ T444] sd 2:0:0:0: [sdc] tag#0 access beyond end of device rpcbind: Input/output error [ 80.902592][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.912514][ T445] sd 2:0:0:0: [sdc] tag#0 access beyond end of device nfs-common: Input/output error [ 80.923148][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.933426][ T446] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.944140][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 80.954325][ T447] sd 2:0:0:0: [sdc] tag#0 access beyond end of device mountnfs-bootclean.sh: Input/out[ 80.965000][ T199] sd 2:0:0:0: [sdc] tag#0 access beyond end of device put error [ 80.975225][ T448] sd 2:0:0:0: [sdc] tag#0 access beyond end of device bootmisc.sh: Input/output error INIT: Entering runlevel: 2ned failure: mountdevsubfs.sh checkroo Using makefile-style concurrent boot in runlevel 2. [ 81.134052][ T454] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 81.141029][ T454] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 81.148137][ T454] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 81.154763][ T454] EXT4-fs warning (device sdc1): htree_dirblock_to_tree:1082: inode #98699: lblock 0: comm startpar: error -5 reading directory block [ 81.174417][ T455] sd 2:0:0:0: [sdc] tag#0 access beyond end of device [ 81.181237][ T455] sd 2:0:0:0: [sdc] tag#0 access beyond end of device INIT: cannot execute "/sbin/getty" [ 81.221593][ T456] sd 2:0:0:0: [sdc] tag#0 access beyond end of device INIT: cannot execute "/sbin/getty" [ 81.261639][ T457] sd 2:0:0:0: [sdc] tag#0 access beyond end of device INIT: cannot execute "/sbin/getty" [ 81.301606][ T458] sd 2:0:0:0: [sdc] tag#0 access beyond end of device INIT: cannot execute "/sbin/getty" [ 81.341627][ T459] sd 2:0:0:0: [sdc] tag#0 access beyond end of device INIT: cannot execute "/sbin/getty" [ 81.381611][ T460] sd 2:0:0:0: [sdc] tag#0 access beyond end of device INIT: cannot execute "/sbin/getty" [ 81.421650][ T461] sd 2:0:0:0: [sdc] tag#0 access beyond end of device INIT: cannot execute "/sbin/getty" [ 81.461604][ T462] sd 2:0:0:0: [sdc] tag#0 access beyond end of device INIT: cannot execute "/sbin/getty" [ 81.501607][ T463] sd 2:0:0:0: [sdc] tag#0 access beyond end of device INIT: cannot execute "/sbin/getty" [ 81.541601][ T464] sd 2:0:0:0: [sdc] tag#0 access beyond end of device INIT: cannot execute "/sbin/getty" INIT: Id "T0" respawning too fast: disabled for 5 minutes INIT: no more processes left in this runlevel