Arch Linux on Lenovo ix2 NAS stuck at Starting kernel (no replies)

hello, i tried to install arch linux on my lenovo iomega ix2 nas, but i failed every time because it gets stuck at the point where it just says starting kernel ... . I have also read the other posts, but unfortunately nothing has helped. Can someone please help me.


| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** ix2-spi ** ** uboot_ver:0.0.8 **

** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Oct 28 2011 - 15:18:22) Marvell version: 3.6.1 - EMC

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[1024kB@f8000000] Flash: 1 MB

Marvell Serial ATA Adapter
Integrated Sata device found
[0 1 0]: Enable DMA mode (5)
Device 1 @ 0 1:
Model: WDC WD10EZEX-08WN4A0 Firm: 01.01A01 Ser#: WD-WCC6Y4VEC00F
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)


CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
.
....
......
............
.
.........................
.........................
........................
.
.........................
.........................
.........................
.........................
.........................
.........................
.........................
.........................
.........................
.........................
.........................
.........................
.........................
..............

4612216 bytes read
.
....
......
............
.
........................
.
.........................
........................
.
.........................
.........................
.........................
........................
.
.........................
.........................
.........................
.........................
.........................
.........................
.........................
........................
.
.........................
.........................
.........................
.........................
.........................
.........................
.........................
........................
.
.........................
.....................

6788126 bytes read
## Booting image at 01000000 ...
Image Name: Linux-4.4.176-1-ARCH
Created: 2019-02-23 19:03:13 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4612152 Bytes = 4.4 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 08004000 ...
Image Name: Arch Linux ARM initrd
Created: 2025-02-28 20:03:20 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 6788062 Bytes = 6.5 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK

Starting kernel ...