Hello,
Thank you, Bodhi and others, for supporting the EOL NAS.
I have an NSA325 with stock firmware which used as a backup nas.
For the past few days, my NAS device has been unable to boot up or be accessed over the network. There might be a problem with the NAND or the network interface. I'm not sure exactly what the problem is.
Try booting with UART. I can read the boot logs, but they don't help me understand what happened.
Can I continue using this device for data storage, or is it completely unusable due to a hardware failure?
Thank you for your help.
The log of booting with stock firmware
I've tried with Kwboot and the rootfs, but no network interface was detected.
Thank you, Bodhi and others, for supporting the EOL NAS.
I have an NSA325 with stock firmware which used as a backup nas.
For the past few days, my NAS device has been unable to boot up or be accessed over the network. There might be a problem with the NAND or the network interface. I'm not sure exactly what the problem is.
Try booting with UART. I can read the boot logs, but they don't help me understand what happened.
Can I continue using this device for data storage, or is it completely unusable due to a hardware failure?
Thank you for your help.
The log of booting with stock firmware
picocom -b 115200 /dev/ttyUSB0
picocom v3.1
port is : /dev/ttyUSB0
flowcontrol : none
baudrate is : 115200
parity is : none
databits are : 8
stopbits are : 1
escape is : C-a
local echo is : no
noinit is : no
noreset is : no
hangup is : no
nolock is : no
send_cmd is : sz -vv
receive_cmd is : rz -vv -E
imap is :
omap is :
emap is : crcrlf,delbs,
logfile is : none
initstring : none
exit_after is : not set
exit is : no
Type [C-a] [C-h] to see available commands
Terminal ready
�
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: DB-88F6282A-BP LE
U-Boot 1.1.4 (Jan 29 2013 - 12:01:09) Marvell version: 3.5.9
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00
Soc: 88F6282 A1CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 7 tRP = 8 tRAS = 24 tRCD=8
DRAM CS[0] base 0x00000000 size 512MB
DRAM Total size 512MB 16bit width
Addresses 10M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (10M - 7M): Done
NAND:128 MB
Flash: 0 kB
CPU : Marvell Feroceon (Rev 1)
Kernel address is 0x4640000.
Streaming disabled
Write allocate disabled
USB 0: host mode
[BlueDBG] reseting SoC Pex[0] 0 ...
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
[BlueDBG] reseting SoC Pex[1] 0 ...
[BlueDBG] reseting SoC Pex[1] 1 ...
[BlueDBG] reseting SoC Pex[1] 2 ...
[BlueDBG] reseting SoC Pex[1] 3 ...
[BlueDBG] reseting SoC Pex[1] 4 ...
[BlueDBG] reseting SoC Pex[1] 5 ...
[BlueDBG] reseting SoC Pex[1] 6 ...
[BlueDBG] reseting SoC Pex[1] 7 ...
[BlueDBG] reseting SoC Pex[1] 8 ...
[BlueDBG] reseting SoC Pex[1] 9 ...
[BlueDBG] reseting SoC Pex[1] 10 ...
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x4640000, size 0xa00000
Reading data from 0x503f800 -- 100% complete.
10485760 bytes read: OK
## Booting image at 02000000 ...
Image Name: Linux-2.6.31.8
Created: 2012-11-12 7:27:40 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 6109104 Bytes = 5.8 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux.......................................................................................................................................................................................................................................................................................... done, booting the kernel.
Linux version 2.6.31.8 (root@Neo) (gcc version 4.3.2 (sdk3.3-ct-ng-1.4.1) ) #3 Mon Nov 12 15:27:15 CST 2012
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Feroceon-KW
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 130048
Kernel command line: console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
PID hash table entries: 2048 (order: 11, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 512MB = 512MB total
Memory: 506368KB available (5384K code, 302K data, 3164K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Console: colour dummy device 80x30
Calibrating delay loop... 1599.07 BogoMIPS (lpj=7995392)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
invoking softwareStaggeredSpinUp()..., it will delay 5 seconds to spin up the second harddisk
CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 512MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB
PEX0_IO ....base f2000000, size 1MB
PEX1_MEM ....base e8000000, size 128MB
PEX1_IO ....base f2100000, size 1MB
INTER_REGS ....base f1000000, size 1MB
NFLASH_CS ....base fa000000, size 2MB
SPI_CS ....base f4000000, size 16MB
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT_ENG ....base f0000000, size 2MB
Marvell Development Board (LSP Version KW_LSP_5.1.3_patch18)-- DB-88F6282A-BP Soc: MV88F6282 Rev 1 LE
Detected Tclk 200000000 and SysClk 533333333
Marvell USB EHCI Host controller #0: d003a740
[BlueDBG] reseting SoC Pex[0] 0 ...
PEX0 interface detected Link X1
[BlueDBG] reseting SoC Pex[1] 0 ...
[BlueDBG] reseting SoC Pex[1] 1 ...
[BlueDBG] reseting SoC Pex[1] 2 ...
[BlueDBG] reseting SoC Pex[1] 3 ...
[BlueDBG] reseting SoC Pex[1] 4 ...
[BlueDBG] reseting SoC Pex[1] 5 ...
[BlueDBG] reseting SoC Pex[1] 6 ...
[BlueDBG] reseting SoC Pex[1] 7 ...
[BlueDBG] reseting SoC Pex[1] 8 ...
[BlueDBG] reseting SoC Pex[1] 9 ...
[BlueDBG] reseting SoC Pex[1] 10 ...
PEX1 interface detected no Link.
pci 0000:00:01.0: PME# supported from D0 D3hot
pci 0000:00:01.0: PME# disabled
PCI: bus0: Fast back to back transfers disabled
PCI: bus1: Fast back to back transfers enabled
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Calling CRDA to update world regulatory domain
NET: Registered protocol family 2
IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
TCP established hash table entries: 65536 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
NET: Registered protocol family 1
cpufreq: Init kirkwood cpufreq driver
XOR registered 4 channels
XOR 2nd invalidate WA enabled
mvCesaInit: sessions=640, queue=64, pSram=f0000000
Warning: TS unit is powered off.
gpio_dev = fd00000
LED_SET_CTL_IOC_NUM= 6702
High gpio polarity = 50
High gpio polarity = 70
Enable Interrupt
mv88f6281_wdt: Watchdog Timer timeout = 8 sec.
mv88f6281_wdt: HW Watchdog timeout = 15 sec.
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.12)
SGI XFS with security attributes, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
msgmni has been set to 989
alg: No test for cipher_null (cipher_null-generic)
alg: No test for ecb(cipher_null) (ecb-cipher_null)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Integrated Sata device found
IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs
Wake up disk0......
Wake up disk1......
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
EnablePowerSaving
PowerSavingTime = 15
No found HD
Loading Marvell Ethernet Driver:
o Cached descriptors in DRAM
o DRAM SW cache-coherency
o 1 Giga ports supported
o Single RX Queue support - ETH_DEF_RXQ=0
o Single TX Queue support - ETH_DEF_TXQ=0
o TCP segmentation offload (TSO) supported
o Large Receive offload (LRO) supported
o Receive checksum offload supported
o Transmit checksum offload supported
o Network Fast Processing (Routing) supported - (Disabled)
o Driver ERROR statistics enabled
o Proc tool API enabled
o SKB Reuse supported - (Disabled)
o SKB Recycle supported - (Disabled)
o Rx descripors: q0=128
o Tx descripors: q0=532
o Loading network interface(s):
o register under mv88fx_eth platform
o eth0, ifindex = 2, GbE port = 0
mvFpRuleDb (d1110000): 16384 entries, 65536 bytes
Counter=0, opIdx=6, overhead=16
Counter=1, opIdx=2, overhead=0
Counter=2, opIdx=1, overhead=18
Counter=3, opIdx=2, overhead=0
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 183 at 0x0000016e0000
Bad eraseblock 435 at 0x000003660000
9 cmdlinepart partitions found on MTD device nand_mtd
Using command line partition definition
Creating 9 MTD partitions on "nand_mtd":
0x000000000000-0x000000100000 : "uboot"
0x000000100000-0x000000180000 : "uboot_env"
0x000000180000-0x000000200000 : "key_store"
0x000000200000-0x000000280000 : "info"
0x000000280000-0x000000c80000 : "etc"
0x000000c80000-0x000001680000 : "kernel_1"
0x000001680000-0x000004640000 : "rootfs1"
0x000004640000-0x000005040000 : "kernel_2"
0x000005040000-0x000008000000 : "rootfs2"
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
PCI: enabling device 0000:00:01.0 (0140 -> 0142)
xhci_hcd 0000:00:01.0: xHCI Host Controller
xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 2
xhci_hcd 0000:00:01.0: irq 9, io mem 0xe0000000
usb usb2: config 1 interface 0 altsetting 0 endpoint 0x81 has no SuperSpeed companion descriptor
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
rtc-pcf8563 0-0051: chip found, driver version 0.4.3
rtc-pcf8563 0-0051: rtc core: registered rtc-pcf8563 as rtc0
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
ip6tnl0: Disabled Privacy Extensions
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
rtc-pcf8563 0-0051: setting system clock to 1970-01-02 09:37:44 UTC (121064)
Freeing init memory: 3164K
*** Stage 1: Setup system and device drivers ***
usb 1-1: new high speed USB device using ehci_marvell and address 2
In hub_port_init, and number is 1, retry 0, port 1 .....
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
eth0: mac address changed
egiga0: started
ADDRCONF(NETDEV_UP): egiga0: link is not ready
*** Stage 2: Prepare the root file system ***
Mount system partition...
yaffs: dev is 32505864 name is "mtdblock8" ro
yaffs: passed flags ""
storage_gen_mntfw.sh: no internal disk available
1
WARNING: No valid partition on HDD or no HDD plugged!
WARNING: No valid partition on HDD or no HDD plugged
Boot from RAM disk
Mount system disk image ...
yaffs: dev is 32505860 name is "mtdblock4" rw
yaffs: passed flags ""
/etc/zyxel/conf exist..
/etc/init.d/rcS: line 397: can't create /sys/block/sda/queue/read_ahead_kb: nonexistent directory
Start rcS2 of ZyXEL style
Set the phy back to auto-negotiation mode
base address = 40151000
words[0] = phypoke
words[1] = 1
words[2] = 4
words[3] = 1e1
:GbitPhy[0x00000001:0x00000004] <= 0x000001e1
base address = 40151000
words[0] = phypoke
words[1] = 1
words[2] = 9
words[3] = 300
:GbitPhy[0x00000001:0x00000009] <= 0x00000300
base address = 40151000
words[0] = phypoke
words[1] = 1
words[2] = 0
words[3] = 9NTFS driver 2.1.29 [Flags: R/O MODULE].
140
:GbitPhy[0x00000001:0x00000000] <= 0x00009140
*** Stage 3: Start services on HDD ***
tntfs: module license 'Commercial. For support email ntfs-support@tuxera.com.' taints kernel.
Disabling lock debugging due to kernel taint
Tuxera NTFS driver 3011.12.23 [Flags: R/W MODULE].
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
PPP Deflate Compression module registered
NET: Registered protocol family 24
PPP BSD Compression module registered
modprobe: module fuse not found in modules.dep
Press ENTER to continue...
Starting zylogd...
zylog starts.
Starting uamd...
Starting ZySH daemon and client...
Start NSA-220 system daemon....
Start ZySH daemon
zyshd: version 2.0.0 (build: 11:51:38 Nov 9 2012)
% zylog init start
cat: can't open '/var/run/syslog-ng.pid': No such file or directory
Try to KILL SIGHUP to syslog-ng: pid=0
syslog-ng not running, start /usr/sbin/syslog-ng
Jan 2 09:38:20 (none) syslog-ng[1320]: syslog-ng starting up; version='2.0.10'
zyio_open_config success. (/etc/__system_default.xml, 0)
zyio_open_config success. (/etc/zyxel/conf/__system_default_device_ha.xml, 0)
/usr/sbin/zic -d /etc /var/zyxel/myzone_rule
/bin/ln -s -f /etc/MyZone /etc/localtime
/bin/hostname NSA325
Usage: umount [-hV]
umount -a [-f] [-r] [-n] [-v] [-t vfstypes] [-O opts]
umount [-f] [-r] [-n] [-v] special | node...
Usage: umount [-hV]
umount -a [-f] [-r] [-n] [-v] [-t vfstypes] [-O opts]
umount [-f] [-r] [-n] [-v] special | node...
BusyBox v1.17.2 (2012-11-09 11:45:26 CST) multi-call binary.
Usage: rmdir [OPTIONS] DIRECTORY...
Init SMB DB access...
rm: can't remove '/var/log/samba/smb.db': No such file or directory
zyio_container_create_template(/etc/__system_default.xml): scope:[network/wlan] list:[wlan_list] type:[wlan_t] is not existed
Assemble volume....
[1367] server write-only FIFO is opened (fd=6)
[1367] server read-only FIFO is opened (fd=7)
[1367] server error read-only FIFO is opened (fd=8)
argc = 1, func = 277
Startup config
POLLHUP on 7
pid = 1367
[1367] is disconnected
[1505] server write-only FIFO is opened (fd=6)
[1505] server read-only FIFO is opened (fd=7)
[1505] server error read-only FIFO is opened (fd=8)
argc = 1, func = 14
argc = 1, func = 17
argc = 1, func = 665
argc = 2, func = 104
argid[1]: 1077; argv[1]: ge1
argc = 5, func = 107
argid[1]: 1077; argv[1]: ge1
argid[2]: 313; argv[2]: ip
argid[3]: 434; argv[3]: address
argid[4]: 538; argv[4]: dhcp
argc = 3, func = 105
argid[1]: 1077; argv[1]: ge1
argid[2]: 350; argv[2]: exit
argc = 2, func = 440
argid[1]: 1070; argv[1]: 192.168.1.1
argc = 4, func = 442
argid[1]: 875; argv[1]: fetch
argid[2]: 628; argv[2]: auto
argid[3]: 1077; argv[3]: ge1
/bin/rm -f /var/zyxel/zysh/egiga0.metric
/bin/ip route del default via 0.0.0.0 dev egiga0
RTNETLINK answers: No such process
[1516] server write-only FIFO is opened (fd=9)
[1516] server read-only FIFO is opened (fd=10)
[1516] server error read-only FIFO is opened (fd=11)
argc = 7, func = 77
argid[1]: 267; argv[1]: mail
argid[2]: 1396; argv[2]: 1
argid[3]: 435; argv[3]: category
argid[4]: 375; argv[4]: all
argid[5]: 461; argv[5]: level
argid[6]: 478; argv[6]: alert
mail server '1' log_category(all) is:alert
argc = 1, func = 441
POLLHUP on 10
pid = 1516
[1516] is disconnected
argc = 7, func = 77
argid[1]: 267; argv[1]: mail
argid[2]: 1396; argv[2]: 1
argid[3]: 435; argv[3]: category
argid[4]: 375; argv[4]: all
argid[5]: 461; argv[5]: level
argid[6]: 375; argv[6]: all
mail server '1' log_category(all) is:all
argc = 2, func = 68
argid[1]: 1069; argv[1]: time.stdtime.gov.tw
argc = 2, func = 60
argid[1]: 1120; argv[1]: +0800
/usr/sbin/zic -d /etc /var/zyxel/myzone_rule
/bin/ln -s -f /etc/MyZone /etc/localtime
argc = 1, func = 72
/usr/sbin/ntpdate_agent time.stdtime.gov.tw
Jan 2 17:38:31 (none) ntpdate[1558]: can't find host time.stdtime.gov.tw
Jan 2 17:38:31 (none) ntpdate[1558]: no servers can be used, exiting
argc = 4, func = 343
argid[1]: 1213; argv[1]: ""
argid[2]: 593; argv[2]: in
argid[3]: 1214; argv[3]: "NULL"
argc = 1, func = 38
killall: pure-ftpd: no process killed
Usage: umount [-hV]
umount -a [-f] [-r] [-n] [-v] [-t vfstypes] [-O opts]
umount [-f] [-r] [-n] [-v] special | node...
Usage: umount [-hV]
umount -a [-f] [-r] [-n] [-v] [-t vfstypes] [-O opts]
umount [-f] [-r] [-n] [-v] special | node...
BusyBox v1.17.2 (2012-11-09 11:45:26 CST) multi-call binary.
Usage: rmdir [OPTIONS] DIRECTORY...
argc = 6, func = 174
argid[1]: 456; argv[1]: share
argid[2]: 626; argv[2]: save
argid[3]: 1158; argv[3]: "public"
argid[4]: 395; argv[4]: path
argid[5]: 1160; argv[5]: "/i-data/md0/public"
folder is not under mount point.
argc = 7, func = 163
argid[1]: 456; argv[1]: share
argid[2]: 626; argv[2]: save
argid[3]: 1158; argv[3]: "public"
argid[4]: 395; argv[4]: path
argid[5]: 1160; argv[5]: "/i-data/md0/public"
argid[6]: 350; argv[6]: exit
share path /i-data/md0/public not existing.
share path /i-data/md0/video not existing.
share path /i-data/md0/photo not existing.
share path /i-data/md0/music not existing.
share path /i-data/md0/admin not existing.
RegenSmbConfigFile:2201 Close file ok
argc = 6, func = 174
argid[1]: 456; argv[1]: share
argid[2]: 626; argv[2]: save
argid[3]: 1158; argv[3]: "video"
argid[4]: 395; argv[4]: path
argid[5]: 1160; argv[5]: "/i-data/md0/video"
folder is not under mount point.
argc = 7, func = 175
argid[1]: 456; argv[1]: share
argid[2]: 626; argv[2]: save
argid[3]: 1158; argv[3]: "video"
argid[4]: 395; argv[4]: path
argid[5]: 1160; argv[5]: "/i-data/md0/video"
argid[6]: 612; argv[6]: media-server
argc = 7, func = 163
argid[1]: 456; argv[1]: share
argid[2]: 626; argv[2]: save
argid[3]: 1158; argv[3]: "video"
argid[4]: 395; argv[4]: path
argid[5]: 1160; argv[5]: "/i-data/md0/video"
argid[6]: 350; argv[6]: exit
share path /i-data/md0/public not existing.
share path /i-data/md0/video not existing.
share path /i-data/md0/photo not existing.
share path /i-data/md0/music not existing.
share path /i-data/md0/admin not existing.
RegenSmbConfigFile:2201 Close file ok
argc = 6, func = 174
argid[1]: 456; argv[1]: share
argid[2]: 626; argv[2]: save
argid[3]: 1158; argv[3]: "photo"
argid[4]: 395; argv[4]: path
argid[5]: 1160; argv[5]: "/i-data/md0/photo"
folder is not under mount point.
argc = 7, func = 175
argid[1]: 456; argv[1]: share
argid[2]: 626; argv[2]: save
argid[3]: 1158; argv[3]: "photo"
argid[4]: 395; argv[4]: path
argid[5]: 1160; argv[5]: "/i-data/md0/photo"
argid[6]: 612; argv[6]: media-server
argc = 7, func = 163
argid[1]: 456; argv[1]: share
argid[2]: 626; argv[2]: save
argid[3]: 1158; argv[3]: "photo"
argid[4]: 395; argv[4]: path
argid[5]: 1160; argv[5]: "/i-data/md0/photo"
argid[6]: 350; argv[6]: exit
share path /i-data/md0/public not existing.
share path /i-data/md0/video not existing.
share path /i-data/md0/photo not existing.
share path /i-data/md0/music not existing.
share path /i-data/md0/admin not existing.
RegenSmbConfigFile:2201 Close file ok
argc = 6, func = 174
argid[1]: 456; argv[1]: share
argid[2]: 626; argv[2]: save
argid[3]: 1158; argv[3]: "music"
argid[4]: 395; argv[4]: path
argid[5]: 1160; argv[5]: "/i-data/md0/music"
folder is not under mount point.
argc = 7, func = 175
argid[1]: 456; argv[1]: share
argid[2]: 626; argv[2]: save
argid[3]: 1158; argv[3]: "music"
argid[4]: 395; argv[4]: path
argid[5]: 1160; argv[5]: "/i-data/md0/music"
argid[6]: 612; argv[6]: media-server
argc = 7, func = 163
argid[1]: 456; argv[1]: share
argid[2]: 626; argv[2]: save
argid[3]: 1158; argv[3]: "music"
argid[4]: 395; argv[4]: path
argid[5]: 1160; argv[5]: "/i-data/md0/music"
argid[6]: 350; argv[6]: exit
share path /i-data/md0/public not existing.
share path /i-data/md0/video not existing.
share path /i-data/md0/photo not existing.
share path /i-data/md0/music not existing.
share path /i-data/md0/admin not existing.
RegenSmbConfigFile:2201 Close file ok
argc = 6, func = 174
argid[1]: 456; argv[1]: share
argid[2]: 626; argv[2]: save
argid[3]: 1158; argv[3]: "admin"
argid[4]: 395; argv[4]: path
argid[5]: 1160; argv[5]: "/i-data/md0/admin"
folder is not under mount point.
argc = 7, func = 163
argid[1]: 456; argv[1]: share
argid[2]: 626; argv[2]: save
argid[3]: 1158; argv[3]: "admin"
argid[4]: 395; argv[4]: path
argid[5]: 1160; argv[5]: "/i-data/md0/admin"
argid[6]: 350; argv[6]: exit
share path /i-data/md0/public not existing.
share path /i-data/md0/video not existing.
share path /i-data/md0/photo not existing.
share path /i-data/md0/music not existing.
share path /i-data/md0/admin not existing.
RegenSmbConfigFile:2201 Close file ok
argc = 4, func = 410
argid[1]: 1239; argv[1]: yes
argid[2]: 1240; argv[2]: yes
argid[3]: 1241; argv[3]: yes
Jan 2 17:38:34 (none) dhcpcd[1540]: timed out waiting for a valid DHCP server response
argc = 2, func DisablePowerSaving
= 146
argid[1]:TimerState = 0
1145; argv[1]: EnablePowerSaving
15
PowerSavingTime = 15
No found HD
test0
Test1
Test2
Test3:
argc = 2, func = 669
argid[1]: 1077; argv[1]: ge1
killall: httpd: no process killed
Jan 2 17:38:35 (none) httpd[1697]: [warn] Init: Session Cache is not configured [hint: SSLSessionCache]
Jan 2 17:38:35 (none) httpd[1697]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
Jan 2 17:38:35 (none) httpd[1697]: [warn] RSA server certificate CommonName (CN) `NSA325' does NOT match server name!?
Jan 2 17:38:35 (none) httpd[1697]: [error] mod_auth_zyxel: initialized.
argc = 2, func = 160
argid[1]: 1150; argv[1]: g
exec_cmd complete
eth status = g
ethtest0
Test1
Test2
Test3:
argc = 2, func = 18
argid[1]: 350; argv[1]: exit
argc = 1, func = 20
POLLHUP on 7
pid = 1505
[1505] is disconnected
configure terminal ip smb internal disable "/i-data/md0"
[1706] server write-only FIFO is opened (fd=6)
[1706] server read-only FIFO is opened (fd=7)
[1706] server error read-only FIFO is opened (fd=8)
argc = 4, func = 181
argid[1]: 630; argv[1]: internal
argid[2]: 303; argv[2]: disable
argid[3]: 1172; argv[3]: "/i-data/md0"
share path /i-data/md0/public not existing.
share path /i-data/md0/video not existing.
share path /i-data/md0/photo not existing.
share path /i-data/md0/music not existing.
share path /i-data/md0/admin not existing.
RegenSmbConfigFile:2201 Close file ok
no such autosata.
Error happens when deleting autosata.
POLLHUP on 7
pid = 1706
[1706] is disconnected
configure terminal ip smb internal disable "/i-data/md1"
[1711] server write-only FIFO is opened (fd=6)
[1711] server read-only FIFO is opened (fd=7)
[1711] server error read-only FIFO is opened (fd=8)
argc = 4, func = 181
argid[1]: 630; argv[1]: internal
argid[2]: 303; argv[2]: disable
argid[3]: 1172; argv[3]: "/i-data/md1"
share path /i-data/md0/public not existing.
share path /i-data/md0/video not existing.
share path /i-data/md0/photo not existing.
share path /i-data/md0/music not existing.
share path /i-data/md0/admin not existing.
RegenSmbConfigFile:2201 Close file ok
no such autosata.
Error happens when deleting autosata.
POLLHUP on 7
pid = 1711
[1711] is disconnected
Starting smbd...
Jan 2 17:38:35 (none) httpd[1698]: [warn] RSA server certificate is a CA certificate (BasicConstraints: CA == TRUE !?)
Jan 2 17:38:35 (none) httpd[1698]: [warn] RSA server certificate CommonName (CN) `NSA325' does NOT match server name!?
Jan 2 17:38:35 (none) httpd[1698]: [error] mod_auth_zyxel: initialized.
Starting nmbd...
Starting NSU Agent...
Starting copy auto daylight saving tzfile to /i-data/md0/.system/ ...
cp -a /usr/local/zoneinfo /i-data/md0/.system/
cp: can't create directory '/i-data/md0/.system/': No such file or directory
grep: /proc/nas_model: No such file or directory
storage_gen_swap.sh: not enough space to dd swap file
GMT offset=28800s
setting system time zone to tz_minuteswest=-480
mknod: /dev/btncpy: File exists
setLED COPY OFF
led_state_map_addr = 10
[2180] server write-only FIFO is opened (fd=6)
[2180] server read-only FIFO is opened (fd=7)
[2180] server error read-only FIFO is opened (fd=8)
argc = 2, func = 348
argid[1]: 1215; argv[1]: former
Warning - readback failed
POLLHUP on 7
pid = 2180
[2180] is disconnected
schedule_controller is already running now.
Starting "/etc/init.d/zypkg_controller.sh".
Starting to set up zy-pkgs environment ...
-> No volume exists now. zy-pkgs will not work.
sh: you need to specify whom to kill
Jan 2 17:38:38 (none) syslog-ng[1320]: Termination requested via signal, terminating;
Jan 2 17:38:38 (none) syslog-ng[1320]: syslog-ng shutting down; version='2.0.10'
Jan 2 17:38:38 NSA325 syslog-ng[2222]: syslog-ng starting up; version='2.0.10'
rm: can't remove '/i-data/.system/dropbox/dropbox.enable': No such file or directory
mkdir: can't create directory '/i-data/.system/dropbox': No such file or directory
cp: can't create '/i-data/.system/dropbox/dropbox.db': No such file or directory
mkdir: can't create directory '/i-data/md0/.system/web_cache': No such file or directory
mount: special device /i-data/md0/.system/web_cache does not exist
chmod: /i-data/md0/.system/zyxelFrameworkLog: No such file or directory
chmod: /usr/local/apache/web_framework/data/cache: Read-only file system
chmod: /usr/local/apache/web_framework/data/cache: Read-only file system
Web Server already started.
mkdir: can't create directory '/i-data/md0/': No such file or directory
mkdir: can't create directory '/i-data/md0/': No such file or directory
/bin/nice: /usr/sbin/lld2d: No such file or directory
Starting app_wd...
core_checksum : 8d367898fd52d81ad92b544c4b254655
fwversion : NSA325_4.50(AAAJ.1)
img_checksum : 69fac7dc9752da19102a3c7d61a2e419
modelid : AA03
revision : 36872
romfile_checksum : 781D
zld_checksum : 0e476bd5b78f665bf1795b5b71588892
GbE port 0: TxEnable WA - Enabled, deep=1, tx_en_bk=1
led_state_map_addr = 46
Please press Enter to activate this console. /usr/lib/python2.6/site-packages/flickrapi/__init__.py:45: DeprecationWarning: the md5 module is deprecated; use hashlib instead
Traceback (most recent call last):
File "./cdsdaemon.py", line 472, in <module>
File "./cdsdaemon.py", line 440, in createDB
sqlite3.OperationalError: unable to open database file
Jan 2 17:38:58 NSA325 zcip: init egiga0
Jan 2 17:38:58 NSA325 zcip: start, interface egiga0
Traceback (most recent call last):
File "./cdsdaemon.py", line 472, in <module>
File "./cdsdaemon.py", line 440, in createDB
sqlite3.OperationalError: unable to open database file
Jan 2 17:39:08 NSA325 zcip: config egiga0 169.254.121.243
Jan 2 17:39:08 NSA325 zcip: script /usr/share/zcip.script config failed, exitcode=1
Traceback (most recent call last):
File "./cdsdaemon.py", line 472, in <module>
File "./cdsdaemon.py", line 440, in createDB
sqlite3.OperationalError: unable to open database file
Traceback (most recent call last):
File "./cdsdaemon.py", line 472, in <module>
File "./cdsdaemon.py", line 440, in createDB
sqlite3.OperationalError: unable to open database file
Traceback (most recent call last):
File "./cdsdaemon.py", line 472, in <module>
File "./cdsdaemon.py", line 440, in createDB
sqlite3.OperationalError: unable to open database file
Jan 2 17:39:33 NSA325 dhcpcd[2346]: timed out waiting for a valid DHCP server response
Traceback (most recent call last):
File "./cdsdaemon.py", line 472, in <module>
File "./cdsdaemon.py", line 440, in createDB
sqlite3.OperationalError: unable to open database file
Traceback (most recent call last):
File "./cdsdaemon.py", line 472, in <module>
File "./cdsdaemon.py", line 440, in createDB
sqlite3.OperationalError: unable to open database file
Traceback (most recent call last):
File "./cdsdaemon.py", line 472, in <module>
File "./cdsdaemon.py", line 440, in createDB
sqlite3.OperationalError: unable to open database file
Traceback (most recent call last):
File "./cdsdaemon.py", line 472, in <module>
File "./cdsdaemon.py", line 440, in createDB
sqlite3.OperationalError: unable to open database file
Traceback (most recent call last):
File "./cdsdaemon.py", line 472, in <module>
File "./cdsdaemon.py", line 440, in createDB
sqlite3.OperationalError: unable to open database file
Jan 2 17:40:29 NSA325 dhcpcd[2431]: timed out waiting for a valid DHCP server response
Traceback (most recent call last):
File "./cdsdaemon.py", line 472, in <module>
File "./cdsdaemon.py", line 440, in createDB
sqlite3.OperationalError: unable to open database file
Traceback (most recent call last):
File "./cdsdaemon.py", line 472, in <module>
File "./cdsdaemon.py", line 440, in createDB
sqlite3.OperationalError: unable to open database file
##############################################################
Linux version 2.6.31.8 (root@Neo) (gcc version 4.3.2 (sdk3.3-ct-ng-1.4.1) ) #3 Mon Nov 12 15:27:15 CST 2012
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Feroceon-KW
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 131072
free_area_init_node: node 0, pgdat c08b807c, node_mem_map c08d8000
Normal zone: 1024 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 130048 pages, LIFO batch:31
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 130048
Kernel command line: console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
PID hash table entries: 2048 (order: 11, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 512MB = 512MB total
Memory: 506368KB available (5384K code, 302K data, 3164K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Console: colour dummy device 80x30
Calibrating delay loop... 1599.07 BogoMIPS (lpj=7995392)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
invoking softwareStaggeredSpinUp()..., it will delay 5 seconds to spin up the second harddisk
CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 512MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB
PEX0_IO ....base f2000000, size 1MB
PEX1_MEM ....base e8000000, size 128MB
PEX1_IO ....base f2100000, size 1MB
INTER_REGS ....base f1000000, size 1MB
NFLASH_CS ....base fa000000, size 2MB
SPI_CS ....base f4000000, size 16MB
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT_ENG ....base f0000000, size 2MB
Marvell Development Board (LSP Version KW_LSP_5.1.3_patch18)-- DB-88F6282A-BP Soc: MV88F6282 Rev 1 LE
Detected Tclk 200000000 and SysClk 533333333
Marvell USB EHCI Host controller #0: d003a740
[BlueDBG] reseting SoC Pex[0] 0 ...
PEX0 interface detected Link X1
[BlueDBG] reseting SoC Pex[1] 0 ...
[BlueDBG] reseting SoC Pex[1] 1 ...
[BlueDBG] reseting SoC Pex[1] 2 ...
[BlueDBG] reseting SoC Pex[1] 3 ...
[BlueDBG] reseting SoC Pex[1] 4 ...
[BlueDBG] reseting SoC Pex[1] 5 ...
[BlueDBG] reseting SoC Pex[1] 6 ...
[BlueDBG] reseting SoC Pex[1] 7 ...
[BlueDBG] reseting SoC Pex[1] 8 ...
[BlueDBG] reseting SoC Pex[1] 9 ...
[BlueDBG] reseting SoC Pex[1] 10 ...
PEX1 interface detected no Link.
pci 0000:00:01.0: reg 10 64bit mmio: [0x000000-0x001fff]
pci 0000:00:01.0: PME# supported from D0 D3hot
pci 0000:00:01.0: PME# disabled
PCI: bus0: Fast back to back transfers disabled
PCI: bus1: Fast back to back transfers enabled
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Calling CRDA to update world regulatory domain
NET: Registered protocol family 2
IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
TCP established hash table entries: 65536 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
NET: Registered protocol family 1
cpufreq: Init kirkwood cpufreq driver
cpufreq: High frequency: 1600000KHz - Low frequency: 533333KHz
cpufreq: Setting CPU Frequency to 1600000 KHz
cpufreq: Setting PowerSaveState to off
XOR registered 4 channels
XOR 2nd invalidate WA enabled
mvCesaInit: sessions=640, queue=64, pSram=f0000000
Warning: TS unit is powered off.
gpio_dev = fd00000
LED_SET_CTL_IOC_NUM= 6702
High gpio polarity = 50
High gpio polarity = 70
Enable Interrupt
mv88f6281_wdt: Watchdog Timer timeout = 8 sec.
mv88f6281_wdt: HW Watchdog timeout = 15 sec.
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.12)
SGI XFS with security attributes, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
yaffs built Nov 9 2012 11:58:27 Installing.
YAFFS-WARNING CONFIG_YAFFS_ALWAYS_CHECK_CHUNK_ERASED selected.
msgmni has been set to 989
alg: No test for cipher_null (cipher_null-generic)
alg: No test for ecb(cipher_null) (ecb-cipher_null)
alg: No test for digest_null (digest_null-generic)
alg: No test for compress_null (compress_null-generic)
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Integrated Sata device found
IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs
Wake up disk0......
Wake up disk1......
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
EnablePowerSaving
PowerSavingTime = 15
No found HD
Loading Marvell Ethernet Driver:
o Cached descriptors in DRAM
o DRAM SW cache-coherency
o 1 Giga ports supported
o Single RX Queue support - ETH_DEF_RXQ=0
o Single TX Queue support - ETH_DEF_TXQ=0
o TCP segmentation offload (TSO) supported
o Large Receive offload (LRO) supported
o Receive checksum offload supported
o Transmit checksum offload supported
o Network Fast Processing (Routing) supported - (Disabled)
o Driver ERROR statistics enabled
o Proc tool API enabled
o SKB Reuse supported - (Disabled)
o SKB Recycle supported - (Disabled)
o Rx descripors: q0=128
o Tx descripors: q0=532
o Loading network interface(s):
o register under mv88fx_eth platform
o eth0, ifindex = 2, GbE port = 0
mvFpRuleDb (d1110000): 16384 entries, 65536 bytes
Counter=0, opIdx=6, overhead=16
Counter=1, opIdx=2, overhead=0
Counter=2, opIdx=1, overhead=18
Counter=3, opIdx=2, overhead=0
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 183 at 0x0000016e0000
Bad eraseblock 435 at 0x000003660000
9 cmdlinepart partitions found on MTD device nand_mtd
Using command line partition definition
Creating 9 MTD partitions on "nand_mtd":
0x000000000000-0x000000100000 : "uboot"
0x000000100000-0x000000180000 : "uboot_env"
0x000000180000-0x000000200000 : "key_store"
0x000000200000-0x000000280000 : "info"
0x000000280000-0x000000c80000 : "etc"
0x000000c80000-0x000001680000 : "kernel_1"
0x000001680000-0x000004640000 : "rootfs1"
0x000004640000-0x000005040000 : "kernel_2"
0x000005040000-0x000008000000 : "rootfs2"
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
PCI: enabling device 0000:00:01.0 (0140 -> 0142)
xhci_hcd 0000:00:01.0: xHCI Host Controller
xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 2
xhci_hcd 0000:00:01.0: irq 9, io mem 0xe0000000
usb usb2: config 1 interface 0 altsetting 0 endpoint 0x81 has no SuperSpeed companion descriptor
usb usb2: configuration #1 chosen from 1 choice
xHCI xhci_add_endpoint called for root hub
xHCI xhci_check_bandwidth called for root hub
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
rtc-pcf8563 0-0051: chip found, driver version 0.4.3
rtc-pcf8563 0-0051: rtc core: registered rtc-pcf8563 as rtc0
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
cpufreq: Setting CPU Frequency to 1600000 KHz
cpufreq: Setting PowerSaveState to off
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
ip6tnl0: Disabled Privacy Extensions
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
rtc-pcf8563 0-0051: setting system clock to 1970-01-02 09:37:44 UTC (121064)
Freeing init memory: 3164K
usb 1-1: new high speed USB device using ehci_marvell and address 2
In hub_port_init, and number is 1, retry 0, port 1 .....
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
eth0: mac address changed
egiga0: started
ADDRCONF(NETDEV_UP): egiga0: link is not ready
yaffs: dev is 32505864 name is "mtdblock8" ro
yaffs: passed flags ""
yaffs: Attempting MTD mount of 31.8,"mtdblock8"
yaffs: restored from checkpoint
yaffs_read_super: isCheckpointed 1
yaffs: dev is 32505860 name is "mtdblock4" rw
yaffs: passed flags ""
yaffs: Attempting MTD mount of 31.4,"mtdblock4"
yaffs: restored from checkpoint
yaffs_read_super: isCheckpointed 1
NTFS driver 2.1.29 [Flags: R/O MODULE].
tntfs: module license 'Commercial. For support email ntfs-support@tuxera.com.' taints kernel.
Disabling lock debugging due to kernel taint
Tuxera NTFS driver 3011.12.23 [Flags: R/W MODULE].
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
PPP Deflate Compression module registered
NET: Registered protocol family 24
PPP BSD Compression module registered
DisablePowerSaving
TimerState = 0
EnablePowerSaving
PowerSavingTime = 15
No found HD
GbE port 0: TxEnable WA - Enabled, deep=1, tx_en_bk=1
###############################################################
Marvell>> printenv
bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
bootcmd=nand read.e 0x2000000 $(kernel_addr) 0xA00000; bootm 0x2000000
bootdelay=2
baudrate=115200
loads_echo=0
ipaddr=10.4.52.165
serverip=10.4.52.7
rootpath=/srv/ubuntu
netmask=255.255.255.0
nandEcc=1bit
MODEL_ID=AA03
PRODUCT_NAME=NSA-325
FEATURE_BIT=00
CONTRY_TYPE=FF
VENDOR_NAME=MitraStar Technology Corp.
run_diag=yes
ethaddr=EC:43:F6:86:B3:A0
stdin=serial
stdout=serial
stderr=serial
console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root)
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
ethprime=egiga0
netbsd_en=no
vxworks_en=no
bootargs_root=root=/dev/nfs rw
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
lcd0_enable=0
lcd0_params=640x480-16@60
disaMvPnp=no
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
image_multi=yes
enaAutoRecovery=yes
kernel_addr=0x4640000
pcieTune=no
pcieTune1=no
ethact=egiga0
Environment size: 1563/131068 bytes
Marvell>>
#############################################################################
egiga0 Link encap:Ethernet HWaddr EC:43:F6:86:B3:A0
inet addr:169.254.121.243 Bcast:169.254.255.255 Mask:255.255.0.0
UP BROADCAST NOTRAILERS MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:532
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:11
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:6 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:972 (972.0 B) TX bytes:972 (972.0 B)
I've tried with Kwboot and the rootfs, but no network interface was detected.