Pogoplug v2 Uboot woes (5 replies)

I've been reading through these forums for a few days and cannot figure out my issue.

I have a pogoplug v2 that I've been running happily as an arch server for about 4 years. The other day, I lost power to the device and it no longer boots. I hooked a serial up to it and I can get the uboot terminal, so that's good (from what I've read)

Here's what I get when I boot with the a USB containing my old alarm install. The output is the same when compared to a newly created arch install as well as one I have from a working pogoplug:

U-Boot 2014.04.R3-1 (May 26 2014 - 19:45:55) Arch Linux ARM
Pogo E02

SoC:   Kirkwood 88F6281_A0
DRAM:  256 MiB
WARNING: Caches not enabled
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
Hit any key to stop autoboot:  0
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
** File not found /rescueme **
** Unrecognized filesystem type **
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "mtd=3"
UBI: MTD device size:            91 MiB
UBI: number of good PEBs:        727
UBI: number of bad PEBs:         1
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     0
UBI: available PEBs:             716
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "rootfs", error -22
UBIFS error (pid 0): ubifs_mount: Error reading superblock on volume 'rootfs' errno=-22!

ubifsmount - mount UBIFS volume

Usage:
ubifsmount <volume-name>
    - mount 'volume-name' volume
1 bytes read in 112 ms (0 Bytes/s)
Found bootable drive on usb 0:1
EHCI timed out on TD - token=0xa0008d80
EHCI timed out on TD - token=0x20008d80
EHCI timed out on TD - token=0x20008d80
 ** ext4fs_devread read error - block
** File not found /boot/uInitrd **
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-3.14.4-1-ARCH
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3965072 Bytes = 3.8 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... Bad Data CRC
ERROR: can't get kernel image!
stopping USB..
Unknown command 'fsload' - try 'help'
Unknown command 'fsload' - try 'help'
resetting ...

and then it does that on a loop.

Here's what it does when I reboot with no USB device plugged in:

SoC:   Kirkwood 88F6281_A0
DRAM:  256 MiB
WARNING: Caches not enabled
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
Hit any key to stop autoboot:  0
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
** Bad device usb 0 **
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "mtd=3"
UBI: MTD device size:            91 MiB
UBI: number of good PEBs:        727
UBI: number of bad PEBs:         1
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     0
UBI: available PEBs:             716
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "rootfs", error -22
UBIFS error (pid 0): ubifs_mount: Error reading superblock on volume 'rootfs' errno=-22!

ubifsmount - mount UBIFS volume

Usage:
ubifsmount <volume-name>
    - mount 'volume-name' volume
** Bad device usb 0 **
** Bad device usb 1 **
** Bad device usb 2 **
** Bad device usb 3 **
** Bad device usb 0 **
** Bad device usb 0 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
Unknown command 'fsload' - try 'help'
Unknown command 'fsload' - try 'help'
resetting ...

Here's what I get when I printenv:

PogoE02> printenv
arcNumber=3542
baudrate=115200
bootargs=$(console) $(bootargs_root)
bootargs_root=root=/dev/mtdblock2 ro
bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset
bootdelay=3
bootm=echo Booting from ${disk} ...; run setargs; bootm ${loadaddr};
bootz=echo Booting from ${disk} ...; run setargs; bootz ${loadaddr} - ${fdt_addr};
console=ttyS0,115200
ethact=egiga0
ethaddr=00:25:31:00:95:6A
fdt_addr=0x800000
fdt_file=/boot/dtbs/kirkwood-pogo_e02.dtb
force_rescue=0
force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi
importbootenv=echo Importing environment (uEnv.txt)...; env import -t $loadaddr $filesize
ipaddr=192.168.1.99
led_error=orange blinking
led_exit=green off
led_init=green blinking
load=echo Attempting to boot from ${type} ${disk}:1...;if run loadbootenv; then run importbootenv;fi;echo Checking if uenvcmd is set ...;if test -n $uenvcmd; then echo Running uenvcmd ...;run uenvcmd;fi;echo Running default loadzimage ...;if run loadzimage; then run loadfdt;run bootz;fi;echo Running default loaduimage ...;if run loaduimage; then run bootm;fi;
loadaddr=0x810000
loadbootenv=load ${type} ${disk}:1 ${loadaddr} /boot/uEnv.txt
loadfdt=load ${type} ${disk}:1 ${fdt_addr} ${fdt_file}
loaduimage=load ${type} ${disk}:1 ${loadaddr} ${uimage}
loadzimage=load ${type} ${disk}:1 ${loadaddr} ${zimage}
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
partition=nand0,2
pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi
rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi
rescue_installed=0
rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params
serverip=192.168.1.89
setargs=setenv bootargs console=${console},${baudrate} ${optargs} root=/dev/sd${letter}1 rw rootwait ${mtdparts}
stderr=serial
stdin=serial
stdout=serial
ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi
ubifs_mtd=3
ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params
uimage=/boot/uImage
usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot
usb_device=0:1
usb_init=run usb_scan
usb_root=/dev/sda1
usb_rootdelay=10
usb_rootfstype=ext3
usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done
usb_scan_1=usb=0:1 dev=sda1
usb_scan_2=usb=1:1 dev=sdb1
usb_scan_3=usb=2:1 dev=sdc1
usb_scan_4=usb=3:1 dev=sdd1
usb_scan_list=1 2 3 4
usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params
zimage=/boot/zImage

Environment size: 3558/131068 bytes

I can't get it to boot into the PogoPlug OS, nor can I get it to the point where it will connect via ethernet. Ethernet port just flashes when I plug in the cable, despite having a valid IP schema in the environment.

Does anyone have anything that they'd like me to try or any suggestions?

Thanks!