Hi all,
I have dockstars which in some point in time didn't get back up again.
Using a Nokia USB-cable with some test hooks, tftp'ed mtd0, 1, 2 and installed rescue from USB stick.
Unfortunately, they don't boot the USB stick which installed without error messages (wheezy-script)
I attached my environment.
uname -a
Linux pogo02-rescue 3.3.2-kirkwide #1 Mon Oct 29 17:52:07 CDT 2012 armv5tel GNU/Linux
Please help me making the devices work again.
#update#
######start boot-log ########
U-Boot 2011.12 (Feb 12 2012 - 21:33:07)
Seagate FreeAgent DockStar
SoC: Kirkwood 88F6281_A0
DRAM: 128 MiB
WARNING: Caches not enabled
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/rescueme" from usb device 0:1 (usbda1)
** File not found /rescueme
reading /rescueme.txt
** Unable to read "/rescueme.txt" from usb 0:1 **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000010000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 219 MiB
UBI: number of good PEBs: 1752
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 1731
UBI: total number of reserved PEBs: 21
UBI: number of PEBs reserved for bad PEB handling: 17
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
1 bytes read
Found bootable drive on usb 0:1
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
1606576 bytes read
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
6883383 bytes read
## Booting kernel from Legacy Image at 00800000 ...
Image Name: kernel 3.2.0-4-kirkwood
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1606512 Bytes = 1.5 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: ramdisk 3.2.0-4-kirkwood
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 6883319 Bytes = 6.6 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
######## end bootlog ###########
Thanks in advance and greetings
CP
I have dockstars which in some point in time didn't get back up again.
Using a Nokia USB-cable with some test hooks, tftp'ed mtd0, 1, 2 and installed rescue from USB stick.
Unfortunately, they don't boot the USB stick which installed without error messages (wheezy-script)
I attached my environment.
uname -a
Linux pogo02-rescue 3.3.2-kirkwide #1 Mon Oct 29 17:52:07 CDT 2012 armv5tel GNU/Linux
Please help me making the devices work again.
#update#
######start boot-log ########
U-Boot 2011.12 (Feb 12 2012 - 21:33:07)
Seagate FreeAgent DockStar
SoC: Kirkwood 88F6281_A0
DRAM: 128 MiB
WARNING: Caches not enabled
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/rescueme" from usb device 0:1 (usbda1)
** File not found /rescueme
reading /rescueme.txt
** Unable to read "/rescueme.txt" from usb 0:1 **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000010000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 219 MiB
UBI: number of good PEBs: 1752
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 1731
UBI: total number of reserved PEBs: 21
UBI: number of PEBs reserved for bad PEB handling: 17
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
1 bytes read
Found bootable drive on usb 0:1
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
1606576 bytes read
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
6883383 bytes read
## Booting kernel from Legacy Image at 00800000 ...
Image Name: kernel 3.2.0-4-kirkwood
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1606512 Bytes = 1.5 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: ramdisk 3.2.0-4-kirkwood
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 6883319 Bytes = 6.6 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
######## end bootlog ###########
Thanks in advance and greetings
CP