Cannot boot any image anymore pogoplug V4 (2 replies)

I've had some issues since I've updated to the newer uboot on my V4, and I'm not sure if it's a hardware problem or uboot environment variable problem.
I used to be able to boot up since I updated the uboot, but it seems after a power outage that I am locked out.
My netcat still works, and I can change variables, but I cannot communicate after any image supposedly boots.
I have tried multiple usb sticks, rootfs versions(3.18.5-3.14) and rescue fs as well.
Can anybody see any issues in my env that may be causing issues?
Pulling my hair out.
Thanks!

Pogov4> printenv
 p r i n t e n v 
arcNumber=3960
baudrate=115200
bootcmd=run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; reset
bootcmd_mmc=run mmc_init; run set_bootargs_mmc; run mmc_boot
bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot;
bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot;
bootdelay=10
console=ttyS0,115200
device=0:1
ethact=egiga0
ethaddr=00:25:re:da:ct:ed
if_netconsole=ping $serverip
ipaddr=192.168.1.128
led_error=orange blinking
led_exit=green off
led_init=green blinking
load_dtb=ext2load usb 0:1 0x1c00000 /boot/dts/kirkwood-pogoplug_v4.dtb
load_initrd=ext2load usb 0:1 0x1100000 /boot/uInitrd
load_uimage=ext2load usb 0:1 0x800000 /boot/uImage
machid=f78
mainlineLinux=yes
mmc_boot=mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
mmc_init=mmc rescan
mmc_load_uimage=ext2load mmc $device 0x800000 /boot/uImage
mmc_load_uinitrd=ext2load mmc $device 0x1100000 /boot/uInitrd
mmc_root=/dev/mmcblk0p1
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
ncip=192.168.1.252
partition=nand0,2
preboot=run preboot_nc
preboot_nc=run if_netconsole start_netconsole
rootdelay=10
rootfstype=ext2
sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
sata_init=ide reset
sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage
sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd
sata_root=/dev/sda1
serverip=192.168.1.252
set_bootargs_mmc=setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=nc
stdin=nc
stdout=nc
usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
usb_init=usb start; setenv usb_root LABEL=rootfs
usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage
usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd
usb_root=/dev/sda1

Environment size: 2480/131068 bytes

here is an example of boot

Pogov4> run usb_boot
 r u n   u s b _ b o o t 
2756040 bytes read in 401 ms (6.6 MiB/s)
6032465 bytes read in 520 ms (11.1 MiB/s)
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-3.16.0-kirkwood-tld-2
   Created:      2014-09-01  23:18:31 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2755976 Bytes = 2.6 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
   Image Name:   initramfs-3.16.0-kirkwood-tld-2
   Created:      2014-09-01  23:18:48 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    6032401 Bytes = 5.8 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK


Starting kernel ...