Debian is running successful on my NSA310s, so I decided to do this on the NSA320s too but ther were some trouble:
None of my usb sticks were recognized at U-Boot stage including the SanDisk Cruizer Blade.
Now let's start the USB:
Now let's (re) start the USB
The other Thing is:
I've updated the stock ZyXEL OS to 4.70, changed the U-Boot environment to boot debian (the default env is the same es on NSA310s) but now every second boot, the older ZyXEL OS is up.
On serial console I can't see why.
The third thing is, that the NSA320s will go on shortly If I connect the power supply.
when it's off after a half second I can power it on and it will stay on.
changing the power supply doesn't "help"
None of my usb sticks were recognized at U-Boot stage including the SanDisk Cruizer Blade.
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: DB6702A-GMtech LE
U-Boot 1.1.4 (Sep 3 2013 - 16:27:22) Marvell version: 3.6.0
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00
Soc: 88F6702 A1 CPU running @ 1000Mhz L2 running @ 500Mhz
SysClock = 400Mhz , TClock = 166Mhz
DRAM (DDR2) CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 10M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (10M - 7M): Done
NAND:128 MB
Flash: 0 kB
CPU : Marvell Feroceon (Rev 1)
Kernel address is 0xc80000.
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Now let's start the USB:
Marvell>> usb start (Re)start USB... USB: scanning bus for devices... 2 USB Device(s) found Waiting for storage device(s) to settle before scanning... 0 Storage Device(s) found
Marvell>> usb tree
Device Tree:
1 Hub (480MBit/s, 0mA)
| Marvell EHCI
|
+-2 Hub (480MBit/s, 100mA)
USB2.0 Hub
Now let's (re) start the USB
Marvell>> usb start / reset (Re)start USB... USB: scanning bus for devices... 1 USB Device(s) found Waiting for storage device(s) to settle before scanning... 0 Storage Device(s) found
Marvell>> usb tree
Device Tree:
1 Hub (12MBit/s, 0mA)
Marvell EHCI
all usb sticks were recongnized when ZyXEL OS is up and running.
The other Thing is:
I've updated the stock ZyXEL OS to 4.70, changed the U-Boot environment to boot debian (the default env is the same es on NSA310s) but now every second boot, the older ZyXEL OS is up.
On serial console I can't see why.
The third thing is, that the NSA320s will go on shortly If I connect the power supply.
when it's off after a half second I can power it on and it will stay on.
changing the power supply doesn't "help"