pogoplug 4: cannot run Debian (3 replies)

Hello,

I am trying to boot Debian on Pogoplug Series 4.

Followed this tutorial: http://blog.qnology.com/2014/07/hacking-pogoplug-v4-series-4-and-mobile.html

After installing Netconsole, rebooted the device accidentally. Tried to run Debian using my PC for writing an image:

mke2fs -L rootfs -j /dev/sdc1
#download Debian rootfs and md5
mount /dev/sdc1 /tmp/mnt
cd /tmp/mnt
wget http://download.qnology.com/pogoplug/v4/Debian-3.14.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2
tar -xjf Debian-3.14.0-kirkwood-tld-1-rootfs-bodhi.tar.bz2
sync
umounn /dev/sdc1

When I try to boot from USB, it freezes:

U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45)
Pogoplug V4
gcc (Debian 4.6.3-14) 4.6.3
GNU ld (GNU Binutils for Debian) 2.22
Hit any key to stop autoboot:  0 
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
2461416 bytes read in 408 ms (5.8 MiB/s)
6362802 bytes read in 597 ms (10.2 MiB/s)
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-3.14.0-kirkwood-tld-1
   Created:      2014-04-06  20:44:27 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2461352 Bytes = 2.3 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
   Image Name:   initramfs-3.14.0-kirkwood-tld-1
   Created:      2014-04-06  20:44:41 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    6362738 Bytes = 6.1 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK


Starting kernel ...

[nothing happens here]

Printenv:

U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45)
Pogoplug V4
gcc (Debian 4.6.3-14) 4.6.3
GNU ld (GNU Binutils for Debian) 2.22
Hit any key to stop autoboot:   0 
Pogov4>  p r i n t e n v 
arcNumber=3960
baudrate=115200
bootcmd=run bootcmd_usb; run bootcmd_mmc; run bootcmd_sata; reset
bootcmd_mmc=run mmc_init; run set_bootargs_mmc; run mmc_boot
bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot;
bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot;
bootdelay=10
console=ttyS0,115200
device=0:1
ethact=egiga0
ethaddr=00:25:31:05:29:a8
if_netconsole=ping $serverip
ipaddr=192.168.1.10
led_error=orange blinking
led_exit=green off
led_init=green blinking
machid=F78
mainlineLinux=yes
mmc_boot=mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
mmc_init=mmc rescan
mmc_load_uimage=ext2load mmc $device 0x800000 /boot/uImage
mmc_load_uinitrd=ext2load mmc $device 0x1100000 /boot/uInitrd
mmc_root=/dev/mmcblk0p1
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
ncip=192.168.1.100
partition=nand0,2
preboot=run if_netconsole start_netconsole
preboot_nc=run if_netconsole start_netconsole
rootdelay=10
rootfstype=ext3
sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
sata_init=ide reset
sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage
sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd
sata_root=/dev/sda1
serverip=192.168.1.100
set_bootargs_mmc=setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=nc
stdin=nc
stdout=nc
usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
usb_init=usb start
usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage
usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd
usb_root=/dev/sda1
usb_rootfstype=ext3

Environment size: 2310/131068 bytes

Any chance to install Debian and/or restore original Pogoplug OS?