USB Booting (EHCI timed out on TD) (2 replies)

Been trying to find a solution since I compiled netatalk (what a mission!) and plugged in 3 other USB's. There's actually about 6 partitions on two of the drives and 3 on the other, 1 on my rootfs.

Can anyone offer some help? It does boot but it takes longer due to scanning the drives and knowing my luck I'm expecting it to mess up!

The last thing I changed was:

fw_setenv usb_init "run usb_scan ; setenv usb_root LABEL=rootfs"

Netconsole:

U-Boot 2014.07-tld-2 (Sep 20 2014 - 00:52:18)
Pogo E02
gcc (Debian 4.6.3-14) 4.6.3
GNU ld (GNU Binutils for Debian) 2.22
Hit any key to stop autoboot:   0 
PogoE02>  p r i n t e n v 
arcNumber=3542
baudrate=115200
bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset
bootdelay=10
console=ttyS0,115200
ethact=egiga0
ethaddr=00:25:31:00:60:EF
force_rescue=0
force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi
if_netconsole=ping $serverip
ipaddr=192.168.0.15
led_error=orange blinking
led_exit=green off
led_init=green blinking
machid=dd6
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
ncip=192.168.0.16
partition=nand0,2
pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi
preboot=run if_netconsole start_netconsole
preboot_nc=setenv nc_ready 0; for pingstat in 1 2 3 4 5; do; sleep 1; if run if_netconsole; then setenv nc_ready 1; fi; done; if test $nc_ready -eq 1; then run start_netconsole; fi
rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi
rescue_installed=0
rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params
serverip=192.168.0.16
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=nc
stdin=nc
stdout=nc
ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi
ubifs_mtd=3
ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params
usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot
usb_device=0:1
usb_init=run usb_scan ; setenv usb_root LABEL=rootfs
usb_root=/dev/sda1
usb_rootdelay=10
usb_rootfstype=ext3
usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done
usb_scan_1=usb=0:1 dev=sda1
usb_scan_2=usb=1:1 dev=sdb1
usb_scan_3=usb=2:1 dev=sdc1
usb_scan_4=usb=3:1 dev=sdd1
usb_scan_list=1 2 3 4
usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts init=/bin/systemd $usb_custom_params

Environment size: 2843/131068 bytes
PogoE02>  b o o t 
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 7 USB Device(s) found
       scanning usb for storage devices... EHCI timed out on TD - token=0x82008d80
READ_CAP ERROR
EHCI timed out on TD - token=0x3c008d80
EHCI timed out on TD - token=0x3c008d80
EHCI timed out on TD - token=0x3c008d80
EHCI timed out on TD - token=0x3c008d80
EHCI timed out on TD - token=0x3c008d80
EHCI timed out on TD - token=0x3c008d80
max USB Storage Device reached: 5 stopping
5 Storage Device(s) found
** File not found /rescueme **
** Unrecognized filesystem type **
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "mtd=3"
UBI: MTD device size:            91 MiB
UBI: number of good PEBs:        728
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     0
UBI: available PEBs:             717
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "rootfs", error -22
UBIFS error (pid 0): ubifs_mount: Error reading superblock on volume 'rootfs' errno=-22!

ubifsmount - mount UBIFS volume

Usage:
ubifsmount <volume-name>
    - mount 'volume-name' volume
1 bytes read in 210 ms (0 Bytes/s)
Found bootable drive on usb 0:1
3092652 bytes read in 335 ms (8.8 MiB/s)
7129314 bytes read in 533 ms (12.8 MiB/s)
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-4.1.0-kirkwood-tld-1
   Created:      2015-07-30  11:01:35 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3092588 Bytes = 2.9 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
   Image Name:   initramfs-4.1.0-kirkwood-tld-1
   Created:      2015-07-30  11:01:43 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    7129250 Bytes = 6.8 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK


Starting kernel ...

Thank you for your help :)
Dannii