Nsa325 v2 - Debian install - stuck (2 replies)

So
I'm trying to install Debian on my Nsa325 v2

I've followed the instructions at : http://zyxel.nas-central.org/wiki/Debian_on_325

I'm using the Kirkwood 3.14 kernel
and the uboot that the page links to.

I've successfully made the Nsa325 v2 look for a USB to boot by using the uboot provided.
It boots from the USB that i've created with the ext2 and ext4 partition, but i end up in (initramfs) with this:

Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Waiting for root file system ... [   24.293451] scsi 0:0:0:0: Direct-Access     SanDisk  Ultra            1.00 PQ: 0 ANSI: 6
[   24.322921] sd 0:0:0:0: [sda] 30031250 512-byte logical blocks: (15.3 GB/14.3 GiB)
[   24.332024] sd 0:0:0:0: [sda] Write Protect is off
[   24.336978] sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00
[   24.344018] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[   24.364776]  sda: sda1 sda2 < sda5 >
[   24.371892] sd 0:0:0:0: [sda] Attached SCSI removable disk
[   24.385393] sd 0:0:0:0: Attached scsi generic sg0 type 0
done.
Begin: Running /scripts/local-premount ... done.
[   24.740299] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
Begin: Running /scripts/local-bottom ... done.
done.
Begin: Running /scripts/init-bottom ... done.
Target filesystem doesn't have requested /sbin/init.
No init found. Try passing init= bootarg.
modprobe: module i8042 not found in modules.dep
[   24.816619] uhci_hcd: USB Universal Host Controller Interface driver
[   24.828348] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   24.840427] usbcore: registered new interface driver usbhid
[   24.846092] usbhid: USB HID core driver


BusyBox v1.20.2 (Debian 1:1.20.0-7) built-in shell (ash)
Enter 'help' for a list of built-in commands.

/bin/sh: can't access tty; job control turned off
(initramfs)

printenv:

Marvell>> printenv
bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/in
it
bootdelay=2
baudrate=115200
loads_echo=0
ipaddr=10.4.52.165
serverip=10.4.52.7
rootpath=/srv/ubuntu

netmask=255.255.255.0
nandEcc=1bit
MODEL_ID=AE03
PRODUCT_NAME=NSA-325v2
FEATURE_BIT=00
CONTRY_TYPE=FF
VENDOR_NAME=MitraStar Technology Corp.
run_diag=yes
console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root)
ethprime=egiga0
bootargs_root=root=/dev/nfs rw
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
lcd0_enable=0
lcd0_params=640x480-16@60
ethaddr=00:50:43:00:02:02
ethmtu=1500
mvPhoneConfig=mv_phone_config=dev[0]:fxs,dev[1]:fxo
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
image_multi=yes
ethact=egiga0
arcNumber=4495
bootargs_stock=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=/dev/nfs rw init=/init
bootargs_linux=console=ttyS0,115200 mtdparts=nand_mtd:0x100000(uboot),0x80000(uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) root=LABEL=rootfs loglevel=8
bootcmd_linux=setenv bootargs $(bootargs_linux); mw.l f1010100 0020c000; usb reset; ext2load usb 0:1 $(loadaddr) /uImage; ext2load usb 0:1 0x01100000 /uInitrd; bootm $(loadaddr) 0x01100000
bootcmd_stock=setenv bootargs $(bootargs_stock); nand read.e $(loadaddr) $(kernel_addr) 0xA00000; bootm $(loadadr)
to_stock=setenv mainlineLinux no; setenv bootcmd \'run bootcmd_stock\'; saveenv; reset
to_linux=setenv mainlineLinux yes; setenv bootcmd \'run bootcmd_linux\'; saveenv; reset
bootcmd='run bootcmd_linux'
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=yes
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
disaMvPnp=no
enaAutoRecovery=yes
kernel_addr=0x4640000
pcieTune=no
pcieTune1=no

Environment size: 2498/131068 bytes

Can anyone help me out?