Hi,
I made an upgrade from Debian Squeeze to Wheezy. After apt-get upgrade the reboot was fine. Then I made apt-get dist-upgrade and now I'm unable to reboot.
Here is the output on netconsole
First with the direct installed kernel
Then I take vmlinuz.bak and initrd.img.old and make rename them to vmlinuz initrd.old. Futhermore I take the bak-Files from /boot/uImage and /boot/uInitrd. With no success.
After that I copied the old /boot/uImage and /boot/uInitrd to the stick (I took them from a backup).
This ends to
Using an old-stick with the backup the output is the following:
I can't see the difference. Can someone give me a hint how to analyze this problem?
In /var/log I can't find any information. All files are old.
I made an upgrade from Debian Squeeze to Wheezy. After apt-get upgrade the reboot was fine. Then I made apt-get dist-upgrade and now I'm unable to reboot.
Here is the output on netconsole
First with the direct installed kernel
U-Boot 2010.09 (Oct 23 2010 - 11:49:22)
Marvell-Dockstar/Pogoplug by Jeff Doozan
Hit any key to stop autoboot: 9 ^C
root@polo:/home/niels# nc -klu 6666
0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/rescueme" from usb device 0:1 (usbda1)
** File not found /rescueme
reading /rescueme.txt
** Unable to read "/rescueme.txt" from usb 0:1 **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000010000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: fixable bit-flip detected at PEB 179
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 219 MiB
UBI: number of good PEBs: 1752
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 1731
UBI: total number of reserved PEBs: 21
UBI: number of PEBs reserved for bad PEB handling: 17
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
1 bytes read
Found bootable drive on usb 0:1
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
1607752 bytes read
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
7233592 bytes read
## Booting kernel from Legacy Image at 00800000 ...
Image Name: kernel 3.2.0-4-kirkwood
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1607688 Bytes = 1.5 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: ramdisk 3.2.0-4-kirkwood
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 7233528 Bytes = 6.9 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Then I take vmlinuz.bak and initrd.img.old and make rename them to vmlinuz initrd.old. Futhermore I take the bak-Files from /boot/uImage and /boot/uInitrd. With no success.
After that I copied the old /boot/uImage and /boot/uInitrd to the stick (I took them from a backup).
This ends to
U-Boot 2010.09 (Oct 23 2010 - 11:49:22)
Marvell-Dockstar/Pogoplug by Jeff Doozan
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/rescueme" from usb device 0:1 (usbda1)
** File not found /rescueme
reading /rescueme.txt
** Unable to read "/rescueme.txt" from usb 0:1 **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000010000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: fixable bit-flip detected at PEB 179
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 219 MiB
UBI: number of good PEBs: 1752
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 1731
UBI: total number of reserved PEBs: 21
UBI: number of PEBs reserved for bad PEB handling: 17
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
1 bytes read
Found bootable drive on usb 0:1
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
1431936 bytes read
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
4738738 bytes read
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-2.6.32-5-kirkwood
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1431872 Bytes = 1.4 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-2.6.32-5-kirkwood
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 4738674 Bytes = 4.5 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Using an old-stick with the backup the output is the following:
OLD_Output
U-Boot 2010.09 (Oct 23 2010 - 11:49:22)
Marvell-Dockstar/Pogoplug by Jeff Doozan
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/rescueme" from usb device 0:1 (usbda1)
** File not found /rescueme
reading /rescueme.txt
** Unable to read "/rescueme.txt" from usb 0:1 **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000010000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: fixable bit-flip detected at PEB 179
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 219 MiB
UBI: number of good PEBs: 1752
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 1731
UBI: total number of reserved PEBs: 21
UBI: number of PEBs reserved for bad PEB handling: 17
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
1 bytes read
Found bootable drive on usb 0:1
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
1431936 bytes read
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
4738738 bytes read
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-2.6.32-5-kirkwood
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1431872 Bytes = 1.4 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-2.6.32-5-kirkwood
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 4738674 Bytes = 4.5 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
I can't see the difference. Can someone give me a hint how to analyze this problem?
In /var/log I can't find any information. All files are old.