Failed to Install latest kernel to NSA310S (2 replies)

Hi! I have an NSA310S on which I would like to install the latest linux kernel (and OMV later), but unfortunately failed.

I have updated tha U-boot to the latest and i have only changed the MAC address in the envs. I have prepared my 4Gb Flash Disk with the kernel (Formated to EXT3 with rootfs label and extracted the bz2 file to the root).

My envs:

NSA3x0S> printenv
arcNumber=4931
baudrate=115200
bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; reset
bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm$load_uimage_addr; fi; fi
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi
bootdelay=10
bootdev=usb
console=ttyS0,115200
device=0:1
devices=usb ide
disks=0 1 2 3
dtb_file=/boot/dts/kirkwood-nsa310s.dtb
ethact=egiga0
ethaddr=E8:37:7A:17:5F:C5
if_netconsole=ping $serverip
ipaddr=192.168.0.231
led_error=orange blinking
led_exit=green off
led_init=green blinking
load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file
load_dtb_addr=0x1c00000
load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd
load_initrd_addr=0x1100000
load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage
load_uimage_addr=0x800000
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2)
partition=nand0,2
preboot_nc=run if_netconsole start_netconsole
scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start";  setenv scan_ide "ide reset";  setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done
serverip=192.168.0.220
set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=serial
stdin=serial
stdout=serial
uenv_addr=0x810000
uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize
uenv_init_devices=setenv init_usb "usb start";  setenv init_ide "ide reset";  setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done;
uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices;  do for disknum in 0; do run uenv_read_disk; done; done;
uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi
uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read;  fi; else if $devtype part $disknum; then run uenv_read; fi;  fi
usb_ready_retry=15

Environment size: 3009/131068 bytes

Bootlog:

U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:50:06 -0700)
ZyXEL NSA310S/320S 1/2-Bay Power Media Server

SoC:   Kirkwood 88F6702_A1
DRAM:  256 MiB
WARNING: Caches not enabled
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
MV88E1318 PHY initialized on egiga0
Hit any key to stop autoboot:  0
starting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
       scanning usb for storage devices...
Use USB retry period from the environment: 15 second(s)
1 Storage Device(s) found

Reset IDE: ide_preinit failed

Partition Map for USB device 0  --   Partition Type: DOS

Part    Start Sector    Num Sectors     UUID            Type
  1     2048            7895040         1f212ad2-01     0f Extd
  5     2112            7894976         1f212ad2-05     83

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0
loading envs from usb 0 ...
** Invalid partition 1 **

no IDE devices available
running scan_disk ...
Scan device usb
device usb 0:1
** Invalid partition 1 **
device usb 1:1
** Bad device usb 1 **
device usb 2:1
** Bad device usb 2 **
device usb 3:1
** Bad device usb 3 **
Scan device ide

Reset IDE: ide_preinit failed
device ide 0:1
** Bad device ide 0 **
device ide 1:1
** Bad device ide 1 **
device ide 2:1
** Bad device ide 2 **
device ide 3:1
** Bad device ide 3 **
loading uImage ...
** Invalid partition 1 **
loading uInitrd ...
** Invalid partition 1 **
loading DTB /boot/dts/kirkwood-nsa310s.dtb ...
** Invalid partition 1 **
Unknown command 'bootm0x800000' - try 'help'
resetting ...

What do I do wrong? Thank you and sorry for my bad English.