Need help in restoring u-boot for Netgear Stora MS2110 (no replies)

Hello guys. Could you please help me with some issues I have with a Netgear Stora MS2110?
This thing was bricked when I got it. I tried to revive it but the official recovery server is history(very bad and disrespectful move if you ask me).
So I started to look for ways to unbrick it and I found this forum. I started to play around with uboot and I have a serial connection established. In my "infinite" wisdom I did a resetenv and now this thing is out of control.

This is what happens when I power up the device:

CPU running @ 1000Mhz L2 running @ 333Mhz
SysClock = 333Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 64MB
DRAM CS[1] base 0x04000000 size 64MB
DRAM Total size 128MB 16bit width
Flash: 0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB
CRC in Flash: ffffffff, Calculated CRC: 619d86db
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
## Error: environment overflow, "stdin" deleted
## Error: environment overflow, "stdout" deleted
## Error: environment overflow, "stderr" deleted

CPU : Marvell Feroceon (Rev 1)
## Error: environment overflow, "console" deleted
## Error: environment overflow, "mainlineLinux" deleted
## Error: environment overflow, "CASset" deleted
## Error: environment overflow, "enaMonExt" deleted
## Error: environment overflow, "enaCpuStream" deleted
## Error: environment overflow, "enaWrAllo" deleted
## Error: environment overflow, "pexMode" deleted
## Error: environment overflow, "disL2Cache" deleted
## Error: environment overflow, "setL2CacheWT" deleted
## Error: environment overflow, "disL2Prefetch" deleted
## Error: environment overflow, "enaICPref" deleted


And goes on and on and on with these "environment overflow" errors and finaly I get the Marvell prompt.

I did manage to save a backup of my previous default environments but when i try to setenv for example:
setenv serveripaddr 192.168.0.1
I get ## Error: environment overflow, "serveripaddr" deleted

Any setenv command returns these "environment overflow" errors.

I do have a flashware.img on hand but again its having trouble with it and I get these errors.

USB 0: device mode
PEX 0: interface detected no Link.
Net: ## Error: environment overflow, "ethact" deleted
egiga0, egiga1## Error: environment overflow, "ethact" deleted

USB: scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Trying to load image from USB flash drive using FAT FS
reading /flashware.img

** Unable to read "/flashware.img" from usb 0:1 **
Trying to load image from USB flash drive using ext2 FS partition 0
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - usb 0:0 **
Trying to load image from USB flash drive using ext2 FS partition 1
....
.................................................................................................

1048576 bytes read
## Error: environment overflow, "filesize" deleted
Missing loadaddr environment variable assuming default (0x400000)!
Update bootcmd
## Error: environment overflow, "bootcmd" deleted
## Error: environment overflow, "console" deleted
Erasing Nand...Writing to Nand... done

bootcmd: setenv bootargs $(console) root=/dev/ram0 rootfstype=squashfs initrd=0x600000,0xffd00000 ramdisk_size=-3072 recovery=usb serverip=0.0.0.0; bootm 0x400000;
## Error: environment overflow, "bootcmd" deleted
Booting the image (@ 0x400000)...
Power Button is pressed!
MPP Sel: 00000530, Data IN Enable: 00020058, Data In Polarity: 00000040, Data In: 00000801
Power Button is released!
MAC: 00:01:4B:C3:DA:75, IP: 10.195.218.117
## Error: environment overflow, "ethaddr" deleted
## Error: environment overflow, "ipaddr" deleted
## Error: environment overflow, "serverip" deleted
## Error: environment overflow, "netmask" deleted
## Error: environment overflow, "image_name" deleted
## Error: environment overflow, "console" deleted
## Error: environment overflow, "bootargs_root" deleted
## Error: environment overflow, "rootpath" deleted
## Error: environment overflow, "ethact" deleted
*** ERROR: `serverip' not set
## Error: environment overflow, "bootargs" deleted
## Booting image at 00800000 ...
Bad Magic Number
Marvell>>

Another weird thing is when i type printenv i get loads of blank screens and at the end
Environment size: 131069/131068 bytes
Marvell>>
The first size is bigger then the second which indicates to me some sort of corrupted data.

So if anyone has had this type of troubles please help me fix it. Im sorry for my bad spelling, english is not my language.
Thanks