Pogo Plug e02 Can't connect over ssh anymore (4 replies)

Hey guys not really sure whats going on. Connected over serial not sure what to do now. Please advise.

sudo picocom -b 115200 /dev/ttyUSB0
picocom v3.1

port is : /dev/ttyUSB0
flowcontrol : none
baudrate is : 115200
parity is : none
databits are : 8
stopbits are : 1
escape is : C-a
local echo is : no
noinit is : no
noreset is : no
hangup is : no
nolock is : no
send_cmd is : sz -vv
receive_cmd is : rz -vv -E
imap is :
omap is :
emap is : crcrlf,delbs,
logfile is : none
initstring : none
exit_after is : not set
exit is : no

Type [C-a] [C-h] to see available commands
Terminal ready


U-Boot 2014.04.R3-1 (May 26 2014 - 19:45:55) Arch Linux ARM
Pogo E02

SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found

no USB devices available

no USB devices available

no USB devices available

no USB devices available
PogoE02> printenv
baudrate=115200
bootcmd=usb start; setenv letter 9;for type in usb; do for disk in 0 1 2 3; do if ${type} part ${disk};then setexpr letter $letter + 1;run load;fi;done;done;
bootdelay=3
bootm=echo Booting from ${disk} ...; run setargs; bootm ${loadaddr};
bootz=echo Booting from ${disk} ...; run setargs; bootz ${loadaddr} - ${fdt_addr};
console=ttyS0
ethact=egiga0
ethaddr=00:25:31:04:AC:05
fdt_addr=0x800000
fdt_file=/boot/dtbs/kirkwood-pogo_e02.dtb
importbootenv=echo Importing environment (uEnv.txt)...; env import -t $loadaddr $filesize
letter=9
load=echo Attempting to boot from ${type} ${disk}:1...;if run loadbootenv; then run importbootenv;fi;echo Checking if uenvcmd is set ...;if test -n $uenvcmd; then echo Running uenvcmd ...;run uenvcmd;fi;echo Running default loadzimage ...;if run loadzimage; then run loadfdt;run bootz;fi;echo Running default loaduimage ...;if run loaduimage; then run bootm;fi;
loadaddr=0x810000
loadbootenv=load ${type} ${disk}:1 ${loadaddr} /boot/uEnv.txt
loadfdt=load ${type} ${disk}:1 ${fdt_addr} ${fdt_file}
loaduimage=load ${type} ${disk}:1 ${loadaddr} ${uimage}
loadzimage=load ${type} ${disk}:1 ${loadaddr} ${zimage}
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1M(u-boot),-(rootfs)
setargs=setenv bootargs console=${console},${baudrate} ${optargs} root=/dev/sd${letter}1 rw rootwait ${mtdparts}
uimage=/boot/uImage
zimage=/boot/zImage

Environment size: 1434/131068 bytes
PogoE02>