Semi-bricked Dockstar help needed: Have netconsole :( (2 replies)

Hello All,

Have been following instructions for a while, but managed to semi-brick the dockstar today, so need some help.

Sequence of events:

1. Decided to upgrade to latest uboot. Did upgrade.
2. Enabled netconsole. Reboot
2. Dockstar never came back up into debian.

What I did:
1. Took backups of mtd0 and uboot using nanddump script before update. Dont know how to restore them with current state. I think restoring those would probably work.
2. Took backup of filesystem before update. Tried restoring it. Didnt help.
3. Based on errors (see below output), did fsck of filesystems from ubuntu box, fixed lots of errors, but it didnt fix the error, leading me to suspect that the upgraded uboot has a different setting or not compatible with my installed kernel?

What I have:
1. Netconsole still works.
2. printenv and netconsole output below:

Netconsole output:

U-Boot 2014.01-tld-1 (Mar 17 2014 - 22:04:15)
Seagate FreeAgent DockStar
gcc (Debian 4.6.3-14) 4.6.3
GNU ld (GNU Binutils for Debian) 2.22
Hit any key to stop autoboot:  0
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
** File not found /rescueme **
** Unrecognized filesystem type **
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "mtd=3"
UBI: MTD device size:            219 MiB
UBI: number of good PEBs:        1752
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     0
UBI: available PEBs:             1731
UBI: total number of reserved PEBs: 21
UBI: number of PEBs reserved for bad PEB handling: 17
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "rootfs", error -22
UBIFS error (pid 0): ubifs_mount: Error reading superblock on volume 'rootfs' er
rno=-22!

ubifsmount - mount UBIFS volume

Usage:
ubifsmount <volume-name>
    - mount 'volume-name' volume
1 bytes read in 557 ms (0 Bytes/s)
Found bootable drive on usb 0:1
EHCI timed out on TD - token=0x1a008d80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x801f8c80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x801f8c80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x801f8c80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x801f8c80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x801f8c80
EHCI timed out on TD - token=0x80008d80
 ** ext4fs_devread read error - block
EHCI timed out on TD - token=0x801f8c80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x801f8c80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x801f8c80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x801f8c80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x801f8c80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x801f8c80
EHCI timed out on TD - token=0x80008d80
** Can't read partition table on 0:0 **
** Invalid partition 1 **
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   kernel 3.2.0-4-kirkwood
   Created:      2013-12-18  19:33:25 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1608432 Bytes = 1.5 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... Bad Data CRC
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: ......... done.
### JFFS2 load complete: 524288 bytes loaded to 0x800000
## Starting application at 0x00800200 ...

Printenv from Netconsole:

U-Boot 2014.01-tld-1 (Mar 17 2014 - 22:04:15)
Seagate FreeAgent DockStar
gcc (Debian 4.6.3-14) 4.6.3
GNU ld (GNU Binutils for Debian) 2.22
Hit any key to stop autoboot: 10
 0
DockStar> printenv
 p r i n t e n v
arcNumber=2097
baudrate=115200
bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd;
 usb stop; run rescue_bootcmd; run pogo_bootcmd; reset
bootdelay=10
console=ttyS0,115200
ethact=egiga0
ethaddr=00:10:75:1A:95:A2
force_rescue=0
force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /
rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd
; fi
if_netconsole=ping $serverip
ipaddr=10.0.0.9
led_error=orange blinking
led_exit=green off
led_init=green blinking
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
ncip=10.0.0.174
partition=nand0,2
pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi
preboot=run if_netconsole start_netconsole
rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; na
nd read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi
rescue_installed=0
rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs
ro rootfstype=ubifs $mtdparts $rescue_custom_params
serverip=10.0.0.174
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; se
tenv stdout nc; setenv stderr nc; version;
stderr=nc
stdin=nc
stdout=nc
ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && u
bifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm
0x800000 0x1100000; fi
ubifs_mtd=3
ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0
:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params
usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext
2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; el
se bootm 0x800000; fi
usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot
usb_device=0:1
usb_init=run usb_scan
usb_root=/dev/sda1
usb_rootdelay=10
usb_rootfstype=ext3
usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if t
est $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_
scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; se
tenv usb_root /dev/$dev; fi; done
usb_scan_1=usb=0:1 dev=sda1
usb_scan_2=usb=1:1 dev=sdb1
usb_scan_3=usb=2:1 dev=sdc1
usb_scan_4=usb=3:1 dev=sdd1
usb_scan_list=1 2 3 4
usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_
rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params

Environment size: 2590/131068 bytes
DockStar>

This is what I have. Can follow instructions. Familiar with Linux command prompt/shell scripting, not a lot on kernel-level stuff.

Help!!!!!!!!!!! :)