[How To] Set U-Boot envs for USB booting with Kirkwood plugs (1 reply)
This is a basic but completed set of U-Boot environment variables that is good for booting Debian/Arch using USB. Please be aware that mistakes in changing U-Boot envs could block you out the box, so...
View ArticleDisplay for pogoplug? (1 reply)
Hi! I have a couple questions and hope someone can help. I'm just getting started with hacking the pogoplug. It seems most folks are hacking the displays to work with dockstars or raspberry pis, but I...
View ArticleSSH Issue lost Debian disk (4 replies)
I have pogoplug pro which was not used from a long time. Now I am trying to make it file server. I lost Usb stick on which debian was installed. Now I formatted new USB drive to install debian but I...
View ArticleMount harddrive in 3.14 (2 replies)
Good evening, Using the 3.14 Debian root, I can boot on the system But after i plugged harddrive on the GoFlex Net, I can't see the hardrive. Only the USB stick is in /dev/ I tried to add mknod, but...
View Articlemtd0 erased / ethernet port is blinking (no replies)
Hello, i erased the 0x80000 and then rebooted. Now is the ethernet port blinking only When i connect with JTAG i see empty black screen. Is there any sollution?
View ArticleSitronix device but script says "Refuse to open device" (1 reply)
Can someone please help me figure out what I need to do? I have the device connected via usb and it is in "Updating" mode. dmesg says: [ 766.337415] scsi 9:0:0:0: Direct-Access SITRONIX MULTIMEDIA...
View ArticleSemi-bricked Dockstar help needed: Have netconsole :( (2 replies)
Hello All, Have been following instructions for a while, but managed to semi-brick the dockstar today, so need some help. Sequence of events: 1. Decided to upgrade to latest uboot. Did upgrade. 2....
View ArticleParagon ntfs module (no replies)
Hi, I was wondering if anyone got the Paragon ntfs drivers to work on their system? Apparently it is 3x faster then the native one. I got this from asus-merlin source code. It has the arm.bin and...
View ArticleBricked my i-Connect ? (2 replies)
I got an i-Connect and wanted to setup a small NAS/Audio server on it. I successfully installed ArchLinux, booting from an USB disk, following http://archlinuxarm.org/forum/viewtopic.php?t=1472. This...
View Articleolder versions of uboot and netconsole? (1 reply)
I've been running squeeze off a usb hard drive on dockstar since I acquired many years ago. Much to my chagrin the dockstar no longer boots off the original cloudengines firmware off internal flash...
View Articleflash gone bad or mere file corruption? (1 reply)
Much to my chagrin my dockstar would no longer boot off internal flash (but still can boot off external usb). I'd really like to have the internal flash work again because it just makes...
View ArticleInstalling Debian on Pogoplug 4 (13 replies)
Hello :-) I'm from Germany and my english is not the best. I buy an Pogoplug 4 from ebay.com to install Debian on it. My Question now is what must I do to install Debian on my Pogoplug 4? please...
View Articleneed u-boot source for Kurobox/Pro (5 replies)
I have a Kurobox/Pro (based on Marvell 88F5182) and am very interested in the Kirkwood thread to amalamte all support for Kirkwood SOC's. I know the 88F5182 is NOT Kirkwood but given a Kurobox/Pro...
View Articleusb problems after recent update (1 reply)
Not sure where the problem lies but after recent kernel update my dockstar will not cold boot from USB HDD. It goes in to rescue, I issue reboot and then it boots from USB HDD. It also seems that it...
View Article"get: write error: No space left on device"??? (no replies)
Got a new pogo p21 (E02) trying to put archlinux on it , the device says it has 125M (using DF - h) available in "tmp" folder but when i try to doenload archlinux it stops about 70% saying "get: write...
View ArticlePogoplug E02 - Just switched to Debian from Arch Linux ARM. How about...
Hi All, I just switched (one of my Pogoplug E02) from Arch Linux ARM to Debian this weekend. Huge thanks to @bodhi for his kernel and rootfs provided in this thread -...
View ArticleUnbricking OMNINAS kd20 (oxnas820) (5 replies)
I have Shuttle Omninas kd20, and I managed to screw its u-boot image in NAND. So it does not boot into u-boot from NAND anymore. The board does have serial header (which I am using), but no JTAG...
View ArticlePossible to use a 3TB+ HDD with Dockstar? (2 replies)
Can I connect a 3TB or larger hard drive to my Dockstar? Do I need some tricks to make it work?
View ArticleGoFlexNet not getting IP (no replies)
I had installed archlinux on my goflexnet around 2 years back. Being a noob, had somehow managed to do it reading over articles on net. Current situation: While I was doing some cleanup, I feel I had...
View ArticleLatest uBoot for Pogoplug Mobile? (no replies)
I just picked up 4 Pogoplug Mobiles from Ebay for a little less than $6 each shipped. What's the latest and greatest uBoot for the Pogoplug Mobile? Would it be davygravy's posted here -...
View Article