root@zyxxy2:/usr/src# ip link add xfrm3 type xfrm dev eth0 if_id 0x123 
Error: Unknown device type.
root@zyxxy2:/usr/src# uname -a
Linux zyxxy2 5.9.12-kirkwood-tld-1 #1.0 PREEMPT Sat Dec 5 14:05:39 PST 2020 armv5tel GNU/Linux
root@zyxxy2:/usr/src#

   __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_ 
| | | |___|  _ \ / _ \ / _ \| __| 
| |_| |___| |_) | (_) | (_) | |_ 
 \___/    |____/ \___/ \___/ \__| 
 ** MARVELL BOARD: RD-88F6281A LE 

U-Boot 1.1.4 (Sep  4 2009 - 09:36:11) Marvell version: 3.4.14

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CEE60

Soc: MV88F6281 Rev 3 (DDR2)
CPU running @ 1000Mhz L2 running @ 333Mhz
SysClock = 333Mhz , TClock = 200Mhz 

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size  64MB 
DRAM CS[1] base 0x04000000   size  64MB 
DRAM Total size 128MB  16bit width
Flash:  0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB
CRC in Flash: ffffffff, Calculated CRC: 619d86db
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
## Error: environment overflow, "stdin" deleted
## Error: environment overflow, "stdout" deleted
## Error: environment overflow, "stderr" deleted

CPU : Marvell Feroceon (Rev 1)
## Error: environment overflow, "console" deleted
## Error: environment overflow, "mainlineLinux" deleted
## Error: environment overflow, "CASset" deleted
## Error: environment overflow, "enaMonExt" deleted
## Error: environment overflow, "enaCpuStream" deleted
## Error: environment overflow, "enaWrAllo" deleted
## Error: environment overflow, "pexMode" deleted
## Error: environment overflow, "disL2Cache" deleted
## Error: environment overflow, "setL2CacheWT" deleted
## Error: environment overflow, "disL2Prefetch" deleted
## Error: environment overflow, "enaICPref" deleted
## Error: environment overflow, "enaDCPref" deleted
## Error: environment overflow, "sata_dma_mode" deleted
## Error: environment overflow, "MALLOC_len" deleted
## Error: environment overflow, "ethprime" deleted
## Error: environment overflow, "netbsd_en" deleted
## Error: environment overflow, "vxworks_en" deleted
## Error: environment overflow, "bootargs_root" deleted
## Error: environment overflow, "bootargs_end" deleted
## Error: environment overflow, "image_name" deleted
## Error: environment overflow, "bootcmd" deleted
## Error: environment overflow, "standalone" deleted
## Error: environment overflow, "bootdelay" deleted
## Error: environment overflow, "disaMvPnp" deleted
## Error: environment overflow, "disaMvPnp" deleted
## Error: environment overflow, "ethaddr" deleted
## Error: environment overflow, "ethmtu" deleted
## Error: environment overflow, "eth1addr" deleted
## Error: environment overflow, "eth1mtu" deleted
## Error: environment overflow, "mvPhoneConfig" deleted
## Error: environment overflow, "mvNetConfig" deleted
## Error: environment overflow, "usb0Mode" deleted
## Error: environment overflow, "yuk_ethaddr" deleted
## Error: environment overflow, "nandEcc" deleted
## Error: environment overflow, "hddPowerCtrl" deleted
## Error: environment overflow, "netretry" deleted
## Error: environment overflow, "rcvrip" deleted
## Error: environment overflow, "loadaddr" deleted
## Error: environment overflow, "autoload" deleted
## Error: environment overflow, "enaAutoRecovery" deleted

Streaming disabled 
Write allocate disabled

Module 0 is RGMII
Module 1 is TDM

USB 0: device mode
PEX 0: interface detected no Link.
Net:   ## Error: environment overflow, "ethact" deleted
egiga0, egiga1## Error: environment overflow, "ethact" deleted

USB:   scanning bus for devices... 1 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
Aquiring an IP address using DHCP...
## Error: environment overflow, "ethact" deleted
egiga0 no link
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
*** ERROR: `ethaddr' not set
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
egiga0 no link
## Error: environment overflow, "ethact" deleted
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
egiga0 no link
## Error: environment overflow, "ethact" deleted
*** ERROR: `eth1addr' not set
## Error: environment overflow, "ethact" deleted
egiga0 no link
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
## Error: environment overflow, "ethact" deleted
egiga0 no link
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
*** ERROR: `ethaddr' not set
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
egiga0 no link
## Error: environment overflow, "ethact" deleted
Failed to retreive an IP address assuming default (<NULL>)!
Starting the Recovery process to retreive the file...
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
egiga0 no link
## Error: environment overflow, "ethact" deleted
*** ERROR: `eth1addr' not set
## Error: environment overflow, "ethact" deleted
egiga0 no link
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
Failed
Power Button is pressed!
MPP Sel: 00000530, Data IN Enable: 00020058, Data In Polarity: 00000040, Data In: 00000010
Power Button is released!
MAC: 00:01:B8:4A:48:0B, IP: 10.74.72.11
## Error: environment overflow, "ethaddr" deleted
## Error: environment overflow, "ipaddr" deleted
## Error: environment overflow, "serverip" deleted
## Error: environment overflow, "netmask" deleted
## Error: environment overflow, "image_name" deleted
## Error: environment overflow, "console" deleted
## Error: environment overflow, "bootargs_root" deleted
## Error: environment overflow, "rootpath" deleted
## Error: environment overflow, "ethact" deleted
egiga0 no link
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
*** ERROR: `serverip' not set
## Error: environment overflow, "bootargs" deleted
## Booting image at 00800000 ...
Bad Magic Number
Marvell>> printenv
��������������������������������������������������
��������������������������������������������������
��������������������������������������������������
Environment size: 131069/131068 bytes
Marvell>>

root@spiderman:/home/linkus/Downloads/kwboot-tool# ./kwboot -t /dev/ttyUSB0 -b uboot.2017.07-tld-1.netgear_ms2110.mtd0.kwb -p
Sending boot message. Please reboot the target...-
Sending boot image...
  0 % [......................................................................]
  1 % [......................................................................]
  3 % [......................................................................]
  5 % [......................................................................]
  6 % [......................................................................]
  8 % [......................................................................]
 10 % [......................................................................]
 11 % [......................................................................]
 13 % [......................................................................]
 15 % [......................................................................]
 17 % [......................................................................]
 18 % [......................................................................]
 20 % [......................................................................]
 22 % [......................................................................]
 23 % [......................................................................]
 25 % [......................................................................]
 27 % [......................................................................]
 29 % [......................................................................]
 30 % [......................................................................]
 32 % [......................................................................]
 34 % [......................................................................]
 35 % [......................................................................]
 37 % [......................................................................]
 39 % [......................................................................]
 41 % [......................................................................]
 42 % [......................................................................]
 44 % [......................................................................]
 46 % [......................................................................]
 47 % [......................................................................]
 49 % [......................................................................]
 51 % [......................................................................]
 53 % [......................................................................]
 54 % [......................................................................]
 56 % [......................................................................]
 58 % [......................................................................]
 59 % [......................................................................]
 61 % [......................................................................]
 63 % [......................................................................]
 64 % [......................................................................]
 66 % [......................................................................]
 68 % [......................................................................]
 70 % [......................................................................]
 71 % [......................................................................]
 73 % [......................................................................]
 75 % [......................................................................]
 76 % [......................................................................]
 78 % [......................................................................]
 80 % [......................................................................]
 82 % [......................................................................]
 83 % [......................................................................]
 85 % [......................................................................]
 87 % [......................................................................]
 88 % [......................................................................]
 90 % [......................................................................]
 92 % [......................................................................]
 94 % [......................................................................]
 95 % [......................................................................]
 97 % [......................................................................]
 99 % [....................................]
[Type Ctrl-\ + c to quit]


U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:38:05 -0700)
Netgear Stora MS2110

SoC:   Kirkwood 88F6281_A1
DRAM:  128 MiB
WARNING: Caches not enabled
NAND:  256 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
PHY reset timed out
88E1116 Initialized on egiga0
Hit any key to stop autoboot:  0 
Netgear Stora> printenv
arcNumber=2743
baudrate=115200
bootargs=$(console) root=LABEL=rootfs rootdelay=8
bootcmd=setenv bootargs $(console) root=LABEL=rootfs rootdelay=8; run bootcmd_usb; bootm 0x200000 0x800000
bootcmd_exec=run load_uimage; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm$load_uimage_addr; fi; fi
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi
bootcmd_usb=usb reset; ext2load usb 0 0x200000 /boot/uImage; ext2load usb 0 0x800000 /boot/uInitrd
bootdelay=10
bootdev=usb
console=console=ttyS0,115200
device=0:1
devices=usb ide
disks=0 1 2 3
dtb_file=/boot/dts/kirkwood-netgear_stora_ms2000
ethact=egiga0
ethaddr=52:3b:20:9c:11:51
fileaddr=800000
filesize=6e8f80
if_netconsole=ping $serverip
ipaddr=192.168.0.231
led_error=orange blinking
led_exit=green off
led_init=green blinking
load_dtb=echo loading DTB $dtb_file ...; load $bootdev $device $load_dtb_addr $dtb_file
load_dtb_addr=0x1c00000
load_initrd=echo loading uInitrd ...; load $bootdev $device $load_initrd_addr /boot/uInitrd
load_initrd_addr=0x1100000
load_uimage=echo loading uImage ...; load $bootdev $device $load_uimage_addr /boot/uImage
load_uimage_addr=0x800000
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1m(uboot),4m@1m(kernel),251m@5m(rootfs) rw
partition=nand0,2
preboot_nc=run if_netconsole start_netconsole
scan_disk=echo running scan_disk ...; scan_done=0; setenv scan_usb "usb start";  setenv scan_ide "ide reset";  setenv scan_mmc "mmc rescan"; for dev in $devices; do if test $scan_done -eq 0; then echo Scan device $dev; run scan_$dev; for disknum in $disks; do if test $scan_done -eq 0; then echo device $dev $disknum:1; if load $dev $disknum:1 $load_uimage_addr /boot/uImage 1; then scan_done=1; echo Found bootable drive on $dev $disknum; setenv device $disknum:1; setenv bootdev $dev; fi; fi; done; fi; done
serverip=192.168.0.220
set_bootargs=setenv bootargs console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 $mtdparts $custom_params
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=serial
stdin=serial
stdout=serial
uenv_addr=0x810000
uenv_import=echo importing envs ...; env import -t $uenv_addr $filesize
uenv_init_devices=setenv init_usb "usb start";  setenv init_ide "ide reset";  setenv init_mmc "mmc rescan"; for devtype in $devices; do run init_$devtype; done;
uenv_load=run uenv_init_devices; setenv uenv_loaded 0; for devtype in $devices;  do for disknum in 0; do run uenv_read_disk; done; done;
uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 $uenv_addr /boot/uEnv.txt; then setenv uenv_loaded 1; fi
uenv_read_disk=if test $devtype -eq mmc; then if $devtype part; then run uenv_read;  fi; else if $devtype part $disknum; then run uenv_read; fi;  fi
usb_ready_retry=15

Environment size: 3118/131068 bytes
Netgear Stora> boot
resetting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 
Use USB retry period from the environment: 15 second(s)
1 Storage Device(s) found
3821592 bytes read in 875 ms (4.2 MiB/s)
7245696 bytes read in 995 ms (6.9 MiB/s)
## Booting kernel from Legacy Image at 00200000 ...
   Image Name:   Linux-4.12.1-kirkwood-tld-1
   Created:      2017-07-20   8:11:24 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3821528 Bytes = 3.6 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 00800000 ...
   Image Name:   initramfs-4.12.1-kirkwood-tld-1
   Created:      2017-07-24   0:18:23 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    7245632 Bytes = 6.9 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
   Loading Ramdisk to 03917000, end 03ffff40 ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.

Error: unrecognized/unsupported machine ID (r1 = 0x00000ab7).

Available machine support:

ID (hex)	NAME
ffffffff	Generic DT based system
ffffffff	Marvell Kirkwood (Flattened Device Tree)

Please check your kernel config and/or bootloader.

Linux debian 5.2.9-kirkwood-tld-1 #1 PREEMPT Sat Aug 17 15:00:56 PDT 2019 armv5tel

The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.

Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
Last login: Wed Dec 31 16:01:28 1969 from 192.168.xxx.yyy
root@debian:~# uname -a
Linux debian 5.2.9-kirkwood-tld-1 #1 PREEMPT Sat Aug 17 15:00:56 PDT 2019 armv5tel GNU/Linux

U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45)
Pogoplug V4

SoC:   Kirkwood 88F6192_A1
DRAM:  128 MiB
WARNING: Caches not enabled
NAND:  128 MiB
MMC:   kwsdio: 0
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
Hit any key to stop autoboot:  0 

MMC rescan: current device # 0 initialized OK
4621184 bytes read in 1036 ms (4.3 MiB/s)
** File not found /boot/uInitrd **
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-4.4.227-1-ARCH
   Created:      2020-06-13   3:57:53 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4621120 Bytes = 4.4 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
Using machid 0xf78 from environment

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.4.227-1-ARCH (builduser@leming) (gcc version 9.3.0 (GCC) ) #1 PREEMPT Sat Jun 13 04:13:48 UTC 2020
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: Pogoplug V4
[    0.000000] Memory policy: Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32480
[    0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p1 rootdelay=10 rootfstype=ext3 mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 119668K/131072K available (6614K kernel code, 548K rwdata, 1892K rodata, 300K init, 720K bss, 11404K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff800000   ( 880 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0856b2c   (8507 kB)
[    0.000000]       .init : 0xc0857000 - 0xc08a2000   ( 300 kB)
[    0.000000]       .data : 0xc08a2000 - 0xc092b35c   ( 549 kB)
[    0.000000]        .bss : 0xc092b35c - 0xc09df508   ( 721 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	Build-time adjustment of leaf fanout to 32.
[    0.000000] NR_IRQS:114
[    0.000019] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns
[   10.582633] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[   10.582917] Console: colour dummy device 80x30
[   10.582963] Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216)
[   10.672738] pid_max: default: 32768 minimum: 301
[   10.672876] Security Framework initialized
[   10.672994] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[   10.673022] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[   10.674135] Initializing cgroup subsys io
[   10.674187] Initializing cgroup subsys memory
[   10.674270] Initializing cgroup subsys devices
[   10.674312] Initializing cgroup subsys freezer
[   10.674345] Initializing cgroup subsys net_cls
[   10.674378] Initializing cgroup subsys perf_event
[   10.674413] Initializing cgroup subsys net_prio
[   10.674533] CPU: Testing write buffer coherency: ok
[   10.675242] Setting up static identity map for 0x81e0 - 0x8238
[   10.678217] devtmpfs: initialized
[   10.681982] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[   10.682045] futex hash table entries: 256 (order: -1, 3072 bytes)
[   10.682928] pinctrl core: initialized pinctrl subsystem
[   10.684059] NET: Registered protocol family 16
[   10.684887] DMA: preallocated 256 KiB pool for atomic coherent allocations
[   10.712770] cpuidle: using governor ladder
[   10.742767] cpuidle: using governor menu
[   10.743055] Kirkwood: MV88F6281-A1, TCLK=166666667.
[   10.743094] Feroceon L2: Enabling L2
[   10.743147] Feroceon L2: Cache support initialised.
[   10.746528] Kirkwood PCIe port 0: link up
[   10.746544] PCI: bus0 uses PCIe port 0
[   10.746885] PCI host bridge to bus 0000:00
[   10.746911] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[   10.746929] pci_bus 0000:00: root bus resource [io  0x1000-0xffff]
[   10.746945] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[   10.748093] PCI: bus0: Fast back to back transfers disabled
[   10.748165] pci 0000:00:01.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff 64bit]
[   10.748199] pci 0000:00:01.0: BAR 2: assigned [mem 0xe0010000-0xe0010fff 64bit]
[   10.748229] pci 0000:00:01.0: BAR 4: assigned [mem 0xe0011000-0xe0011fff 64bit]
[   10.784933] vgaarb: loaded
[   10.785421] SCSI subsystem initialized
[   10.786167] usbcore: registered new interface driver usbfs
[   10.786287] usbcore: registered new interface driver hub
[   10.786371] usbcore: registered new device driver usb
[   10.786597] pps_core: LinuxPPS API ver. 1 registered
[   10.786611] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[   10.786657] PTP clock support registered
[   10.788267] clocksource: Switched to clocksource orion_clocksource
[   10.847156] FS-Cache: Loaded
[   10.865953] NET: Registered protocol family 2
[   10.867086] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[   10.867127] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[   10.867156] TCP: Hash tables configured (established 1024 bind 1024)
[   10.867266] UDP hash table entries: 256 (order: 0, 4096 bytes)
[   10.867298] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[   10.867592] NET: Registered protocol family 1
[   10.868064] RPC: Registered named UNIX socket transport module.
[   10.868080] RPC: Registered udp transport module.
[   10.868090] RPC: Registered tcp transport module.
[   10.868100] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   10.868174] pci 0000:00:01.0: enabling device (0140 -> 0142)
[   10.890550] VFS: Disk quotas dquot_6.6.0
[   10.890955] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   10.893990] FS-Cache: Netfs 'nfs' registered for caching
[   10.895679] NFS: Registering the id_resolver key type
[   10.895751] Key type id_resolver registered
[   10.895762] Key type id_legacy registered
[   10.895894] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[   10.897793] fuse init (API version 7.23)
[   10.901182] aufs 4.4-20170911
[   10.908936] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[   10.908966] io scheduler noop registered
[   10.908985] io scheduler deadline registered
[   10.909386] io scheduler cfq registered
[   10.909764] io scheduler bfq registered (default)
[   10.909776] BFQ I/O-scheduler: v7r11
[   10.910099] mv_xor mv_xor.0: Marvell shared XOR driver
[   10.950165] mv_xor mv_xor.0: Marvell XOR (Registers Mode): ( xor cpy )
[   10.950506] mv_xor mv_xor.1: Marvell shared XOR driver
[   10.990075] mv_xor mv_xor.1: Marvell XOR (Registers Mode): ( xor cpy )
[   10.998247] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[   10.999812] console [ttyS0] disabled
[   11.019896] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 10416666) is a 16550A
[   11.637828] console [ttyS0] enabled
[   11.664684] brd: module loaded
[   11.679205] loop: module loaded
[   11.682859] sata_mv sata_mv.0: cannot get optional clkdev
[   11.688411] sata_mv sata_mv.0: slots 32 ports 1
[   11.695403] scsi host0: sata_mv
[   11.699141] ata1: SATA max UDMA/133 irq 21
[   11.704242] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[   11.710769] nand: Hynix H27U1G8F2BTR-BC
[   11.714596] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[   11.722181] Scanning device for bad blocks
[   11.810266] 5 cmdlinepart partitions found on MTD device orion_nand
[   11.816510] Creating 5 MTD partitions on "orion_nand":
[   11.821656] 0x000000000000-0x000000200000 : "u-boot"
[   11.827331] 0x000000200000-0x000000500000 : "uImage"
[   11.832970] 0x000000500000-0x000000800000 : "uImage2"
[   11.838698] 0x000000800000-0x000001000000 : "failsafe"
[   11.844482] 0x000001000000-0x000008000000 : "root"
[   11.859885] libphy: orion_mdio_bus: probed
[   11.864120] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[   12.058311] ata1: SATA link down (SStatus 0 SControl F300)
[   12.952765] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:05:f5:25
[   12.961703] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   12.968214] ehci-pci: EHCI PCI platform driver
[   12.972795] ehci-orion: EHCI orion driver
[   12.976900] orion-ehci orion-ehci.0: EHCI Host Controller
[   12.982346] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[   12.990119] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[   13.008312] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[   13.015622] hub 1-0:1.0: USB hub found
[   13.019477] hub 1-0:1.0: 1 port detected
[   13.024337] xhci_hcd 0000:00:01.0: xHCI Host Controller
[   13.029649] xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 2
[   13.038593] xhci_hcd 0000:00:01.0: hcc params 0x200073a1 hci version 0x100 quirks 0x00080010
[   13.048394] hub 2-0:1.0: USB hub found
[   13.052181] hub 2-0:1.0: 2 ports detected
[   13.057053] xhci_hcd 0000:00:01.0: xHCI Host Controller
[   13.062345] xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 3
[   13.069863] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[   13.079195] hub 3-0:1.0: USB hub found
[   13.082980] hub 3-0:1.0: 2 ports detected
[   13.088329] usbcore: registered new interface driver uas
[   13.093884] usbcore: registered new interface driver usb-storage
[   13.100039] usbcore: registered new interface driver ums-alauda
[   13.106019] usbcore: registered new interface driver ums-cypress
[   13.112135] usbcore: registered new interface driver ums-datafab
[   13.118192] usbcore: registered new interface driver ums_eneub6250
[   13.125101] usbcore: registered new interface driver ums-freecom
[   13.131196] usbcore: registered new interface driver ums-isd200
[   13.137165] usbcore: registered new interface driver ums-jumpshot
[   13.143335] usbcore: registered new interface driver ums-karma
[   13.149414] usbcore: registered new interface driver ums-onetouch
[   13.155597] usbcore: registered new interface driver ums-realtek
[   13.161687] usbcore: registered new interface driver ums-sddr09
[   13.167665] usbcore: registered new interface driver ums-sddr55
[   13.173666] usbcore: registered new interface driver ums-usbat
[   13.180362] mousedev: PS/2 mouse device common for all mice
[   14.188307] rtc-mv rtc-mv: internal RTC not ticking
[   14.193350] i2c /dev entries driver
[   14.197671] sdhci: Secure Digital Host Controller Interface driver
[   14.203861] sdhci: Copyright(c) Pierre Ossman
[   14.248616] sdhci-pltfm: SDHCI platform and OF driver helper
[   14.258136] ledtrig-cpu: registered to indicate activity on CPUs
[   14.264401] usbcore: registered new interface driver r8712u
[   14.270404] gre: GRE over IPv4 demultiplexor driver
[   14.275367] NET: Registered protocol family 17
[   14.280068] Key type dns_resolver registered
[   14.289046] registered taskstats version 1
[   14.295842] Key type encrypted registered
[   14.300862] console [netcon0] enabled
[   14.304509] netconsole: network logging started
[   14.309870] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[   14.317034] hctosys: unable to open rtc device (rtc0)
[   14.324132] Waiting 10 sec before mounting root device...
[   14.333401] mmc0: host does not support reading read-only switch, assuming write-enable
[   14.346119] mmc0: new high speed SDHC card at address 1234
[   14.352474] mmcblk0: mmc0:1234 SA04G 3.69 GiB 
[   14.361179]  mmcblk0: p1
[   24.341409] EXT4-fs (mmcblk0p1): mounting ext3 file system using the ext4 subsystem
[   28.207784] EXT4-fs (mmcblk0p1): recovery complete
[   28.224598] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
[   28.232747] VFS: Mounted root (ext3 filesystem) on device 179:1.
[   28.241354] devtmpfs: mounted
[   28.245612] Freeing unused kernel memory: 300K
[   29.323474] systemd[1]: System time before build time, advancing clock.
[   29.513747] NET: Registered protocol family 10
[   29.539415] ip_tables: (C) 2000-2006 Netfilter Core Team
[   29.680472] systemd[1]: systemd 246.1-1-arch running in system mode. (+PAM +AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=hybrid)
[   29.704035] systemd[1]: Detected architecture arm.

Welcome to Arch Linux ARM!

[   29.742098] systemd[1]: Set hostname to <alarm>.
[   31.750842] systemd[1]: Queued start job for default target Graphical Interface.
[   31.761670] random: systemd: uninitialized urandom read (16 bytes read, 31 bits of entropy available)
[   31.771563] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling.
[   31.783994] systemd[1]: (This warning is only shown for the first unit using IP firewalling.)
[   31.798164] systemd[1]: Created slice system-getty.slice.
[  OK  ] Created slice system-getty.slice.
[   31.828720] random: systemd: uninitialized urandom read (16 bytes read, 31 bits of entropy available)
[   31.840006] systemd[1]: Created slice system-modprobe.slice.
[  OK  ] Created slice system-modprobe.slice.
[   31.868667] random: systemd: uninitialized urandom read (16 bytes read, 31 bits of entropy available)
[   31.879913] systemd[1]: Created slice system-serial\x2dgetty.slice.
[  OK  ] Created slice system-serial\x2dgetty.slice.
[   31.908607] random: systemd: uninitialized urandom read (16 bytes read, 32 bits of entropy available)
[   31.919674] systemd[1]: Created slice User and Session Slice.
[  OK  ] Created slice User and Session Slice.
[   31.949079] random: systemd: uninitialized urandom read (16 bytes read, 32 bits of entropy available)
[   31.958908] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[  OK  ] Started Dispatch Password …ts to Console Directory Watch.
[   31.988649] random: systemd: uninitialized urandom read (16 bytes read, 32 bits of entropy available)
[   31.998388] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[  OK  ] Started Forward Password R…uests to Wall Directory Watch.
[   32.029335] random: systemd: uninitialized urandom read (16 bytes read, 32 bits of entropy available)
[   32.039605] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[  OK  ] Set up automount Arbitrary…s File System Automount Point.
[   32.069012] random: systemd: uninitialized urandom read (16 bytes read, 32 bits of entropy available)
[   32.078414] systemd[1]: Reached target Local Encrypted Volumes.
[  OK  ] Reached target Local Encrypted Volumes.
[   32.109179] random: systemd: uninitialized urandom read (16 bytes read, 33 bits of entropy available)
[   32.118561] systemd[1]: Reached target Paths.
[  OK  ] Reached target Paths.
[   32.138770] random: systemd: uninitialized urandom read (16 bytes read, 33 bits of entropy available)
[   32.148082] systemd[1]: Reached target Remote File Systems.
[  OK  ] Reached target Remote File Systems.
[   32.178752] systemd[1]: Reached target Slices.
[  OK  ] Reached target Slices.
[   32.198974] systemd[1]: Reached target Swap.
[  OK  ] Reached target Swap.
[   32.219772] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[  OK  ] Listening on Device-mapper event daemon FIFOs.
[   32.276272] systemd[1]: Listening on Process Core Dump Socket.
[  OK  ] Listening on Process Core Dump Socket.
[   32.311416] systemd[1]: Condition check resulted in Journal Audit Socket being skipped.
[   32.321085] systemd[1]: Listening on Journal Socket (/dev/log).
[  OK  ] Listening on Journal Socket (/dev/log).
[   32.349993] systemd[1]: Listening on Journal Socket.
[  OK  ] Listening on Journal Socket.
[   32.380538] systemd[1]: Listening on Network Service Netlink Socket.
[  OK  ] Listening on Network Service Netlink Socket.
[   32.410159] systemd[1]: Listening on udev Control Socket.
[  OK  ] Listening on udev Control Socket.
[   32.439730] systemd[1]: Listening on udev Kernel Socket.
[  OK  ] Listening on udev Kernel Socket.
[   32.470229] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
[   32.486265] systemd[1]: Mounting POSIX Message Queue File System...
         Mounting POSIX Message Queue File System...
[   32.539515] systemd[1]: Mounting Kernel Debug File System...
         Mounting Kernel Debug File System...
[   32.650051] systemd[1]: Mounting Kernel Trace File System...
         Mounting Kernel Trace File System...
[   32.809284] systemd[1]: Mounting Temporary Directory (/tmp)...
         Mounting Temporary Directory (/tmp)...
[   32.940558] systemd[1]: Starting Create list of static device nodes for the current kernel...
         Starting Create list of st…odes for the current kernel...
[   33.203795] systemd[1]: Starting Load Kernel Module drm...
         Starting Load Kernel Module drm...
[   33.305958] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[   33.421691] systemd[1]: Condition check resulted in Load Kernel Modules being skipped.
[   33.559285] systemd[1]: Mounting FUSE Control File System...
         Mounting FUSE Control File System...
[   33.619655] systemd[1]: Condition check resulted in Kernel Configuration File System being skipped.
[   33.722498] systemd[1]: Starting Remount Root and Kernel File Systems...
         Starting Remount Root and Kernel File Systems...
[   33.799302] systemd[1]: Condition check resulted in Repartition Root Disk being skipped.
[   33.912547] systemd[1]: Starting Apply Kernel Variables...
         Starting Apply Kernel Variables...
[   34.039888] systemd[1]: Starting Coldplug All udev Devices...
         Starting Coldplug All udev Devices...
[   34.196563] systemd[1]: Mounted POSIX Message Queue File System.
[  OK  ] Mounted POSIX Message Queue File System.
[   34.310363] systemd[1]: Mounted Kernel Debug File System.
[  OK  ] Mounted Kernel Debug File System.
[   34.354544] systemd[1]: Mounted Kernel Trace File System.
[  OK  ] Mounted Kernel Trace File System.
[   34.440695] systemd[1]: Mounted Temporary Directory (/tmp).
[  OK  ] Mounted Temporary Directory (/tmp).
[   34.462458] systemd[1]: Finished Create list of static device nodes for the current kernel.
[  OK  ] Finished Create list of st… nodes for the current kernel.
[   34.535503] systemd[1]: modprobe@drm.service: Succeeded.
[   34.560563] systemd[1]: Finished Load Kernel Module drm.
[  OK  ] Finished Load Kernel Module drm.
[   34.590185] systemd[1]: Mounted FUSE Control File System.
[  OK  ] Mounted FUSE Control File System.
[   34.632963] systemd[1]: Finished Remount Root and Kernel File Systems.
[  OK  ] Finished Remount Root and Kernel File Systems.
[   34.693166] systemd[1]: Finished Apply Kernel Variables.
[  OK  ] Finished Apply Kernel Variables.
[   34.732196] systemd[1]: Condition check resulted in First Boot Wizard being skipped.
[   34.756018] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[   34.786280] systemd[1]: Starting Load/Save Random Seed...
         Starting Load/Save Random Seed...
[   34.839663] systemd[1]: Condition check resulted in Create System Users being skipped.
[   34.932504] systemd[1]: Starting Create Static Device Nodes in /dev...
         Starting Create Static Device Nodes in /dev...
[   35.413045] systemd[1]: Finished Create Static Device Nodes in /dev.
[  OK  ] Finished Create Static Device Nodes in /dev.
[   35.459842] systemd[1]: Reached target Local File Systems (Pre).
[  OK  ] Reached target Local File Systems (Pre).
[   35.479158] systemd[1]: Condition check resulted in Virtual Machine and Container Storage (Compatibility) being skipped.
[   35.518959] systemd[1]: Reached target Local File Systems.
[  OK  ] Reached target Local File Systems.
[   35.571621] systemd[1]: Started Entropy Daemon based on the HAVEGE algorithm.
[  OK  ] Started Entropy Daemon based on the HAVEGE algorithm.
[   35.620169] systemd[1]: Condition check resulted in Rebuild Dynamic Linker Cache being skipped.
[   35.707253] systemd[1]: Starting Journal Service...
         Starting Journal Service...
[   35.765449] systemd[1]: Condition check resulted in Commit a transient machine-id on disk being skipped.
[   35.931051] systemd[1]: Starting Rule-based Manager for Device Events and Files...
         Starting Rule-based Manage…for Device Events and Files...
[   36.732225] systemd[1]: Finished Coldplug All udev Devices.
[  OK  ] Finished Coldplug All udev Devices.
[**    ] (1 of 4) A start job is running for…e Events and Files (7s / 1min 34s)
[   39.619378] systemd[1]: Started Rule-based Manager for Device Events and File[  OK  ] Started Rule-based Manager for Device Events and Files.
[   39.657040] systemd[1]: Started Journal Service.
[  OK  ] Started Journal Service.
         Starting Flush Journal to Persistent Storage...
         Starting Network Service...
[***   ] (1 of 4) A start job is running for…ersistent Storage (10s / 1min 37s)
[   42.067125] MV-CESA:Could not register sha1 driver
[  *** ] (2 of 4) A start job is running for Network Service (11s / 1min 38s)
[  OK  ] Found device /dev/ttyS0.running for Network Service (12s / 1min 38s)
[  OK  ] Started Network Service.running for…/Save Random Seed (20s / 10min 3s)
[   ***] (1 of 2) A start job is running for…ersistent Storage (22s / 1min 37s)
[ ***  ] (1 of 2) A start job is running for…ersistent Storage (25s / 1min 37s)
[   57.641159] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[  OK  ] Finished Flush Journal to Persistent Storage.dom Seed (36s / 10min 3s)
         Starting Create Volatile Files and Directories...
[  OK  ] Finished Create Volatile Files and Directories.
         Starting Network Name Resolution...
         Starting Network Time Synchronization...
         Starting Update UTMP about System Boot/Shutdown...
[  OK  ] Finished Update UTMP about System Boot/Shutdown.
[    **] (2 of 3) A start job is running for…rk Name Resolution (40s / 2min 7s)
[  OK  ] Finished Load/Save Random Seed. for…rk Name Resolution (40s / 2min 7s)
[  OK  ] Started Network Time Synchronization.
[  OK  ] Reached target System Initialization.
[  OK  ] Started Daily Cleanup of Temporary Directories.
[  OK  ] Reached target System Time Set.
[  OK  ] Reached target System Time Synchronized.
[  OK  ] Started Daily verification of password and group files.
[  OK  ] Reached target Timers.
[  OK  ] Listening on D-Bus System Message Bus Socket.
[  OK  ] Reached target Sockets.
[  OK  ] Reached target Basic System.
[  OK  ] Started D-Bus System Message Bus.
         Starting User Login Management...
[  OK  ] Started Network Name Resolution.
[  OK  ] Reached target Network.
[  OK  ] Reached target Host and Network Name Lookups.
[  OK  ] Started OpenSSH Daemon.
         Starting Hostname Service...
         Starting Permit User Sessions...
[  OK  ] Finished Permit User Sessions.
[  OK  ] Started Getty on tty1.
[  OK  ] Started Serial Getty on ttyS0.
[  OK  ] Reached target Login Prompts.
[  OK  ] Started User Login Management.
[  OK  ] Reached target Multi-User System.
[  OK  ] Reached target Graphical Interface.
[  OK  ] Started Hostname Service.

Arch Linux 4.4.227-1-ARCH (ttyS0)

alarm login:

U-Boot 2014.07-tld-1 (Jul 18 2014 - 00:59:45)
Pogoplug V4

SoC:   Kirkwood 88F6192_A1
DRAM:  128 MiB
WARNING: Caches not enabled
NAND:  128 MiB
MMC:   kwsdio: 0
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
Hit any key to stop autoboot:  0 

MMC rescan: current device # 0 initialized OK
** File not found /boot/uImage **
** File not found /boot/uInitrd **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
(Re)start USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
** Bad device usb 0 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!

Reset IDE: ide_preinit failed
** Bad device size - ide 0 **
** Bad device size - ide 0 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    126976 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          2048 (aligned 2048)
UBI: data offset:                4096
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "mtd=4"
UBI: MTD device size:            112 MiB
UBI: number of good PEBs:        896
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     1
UBI: available PEBs:             0
UBI: total number of reserved PEBs: 896
UBI: number of PEBs reserved for bad PEB handling: 8
UBI: max/mean erase counter: 1/0
UBIFS: recovery needed
UBIFS: recovery deferred
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: mounted read-only
UBIFS: file system size:   110850048 bytes (108252 KiB, 105 MiB, 873 LEBs)
UBIFS: journal size:       9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
UBIFS: media format:       w4/r0 (latest is w4/r0)
UBIFS: default compressor: LZO
UBIFS: reserved for root:  0 bytes (0 KiB)
Loading file 'uboot.mtd0.dockstar.original.kwb' to addr 0x00800000 with size 524288 (0x00080000)...
Done
## Starting application at 0x00800200 ...


U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16)

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 00690D60

Soc: MV88F6192 Rev 3 (DDR2)
CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 200Mhz , TClock = 166Mhz 

DRAM CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3
DRAM CS[0] base 0x00000000   size 128MB 
DRAM Total size 128MB  16bit width
Flash:  0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:128 MB

CPU : Marvell Feroceon (Rev 1)
CLOUD ENGINES BOARD: PPV4A3

Streaming disabled 
Write allocate disabled


USB 0: host mode
PCI 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net:   egiga0 [PRIME], egiga1
Hit any key to stop autoboot:  0 

Loading from NAND 128MB 3,3V 8-bit, offset 0x200000
   Image Name:   Linux-2.6.31.8
   Created:      2011-09-28  19:09:20 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2080956 Bytes =  2 MB
   Load Address: 00008000
   Entry Point:  00008000
## Booting image at 00800000 ...
   Image Name:   Linux-2.6.31.8
   Created:      2011-09-28  19:09:20 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2080956 Bytes =  2 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux..................................................................................................................................... done, booting the kernel.
[    0.000000] Linux version 2.6.31.8 (afenn@kt) (gcc version 4.3.2 (sdk3.3-ct-ng-1.4.1) ) #5 Wed Sep 28 12:09:12 PDT 2011
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053177
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: Feroceon-KW
[    0.000000] Using UBoot passing parameters structure
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 root=ubi0:rootfs ubi.mtd=4,2048 rootfstype=ubifs
[    0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 128MB = 128MB total
[    0.000000] Memory: 118356KB available (3852K code, 261K data, 124K init, 0K highmem)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:128
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Calibrating delay loop... 799.53 BogoMIPS (lpj=3997696)
[    0.230000] Mount-cache hash table entries: 512
[    0.230000] CPU: Testing write buffer coherency: ok
[    0.230000] NET: Registered protocol family 16
[    0.230000] Feroceon L2: Enabling L2
[    0.230000] Feroceon L2: Cache support initialised.
[    0.230000] 
[    0.230000] CPU Interface
[    0.230000] -------------
[    0.230000] SDRAM_CS0 ....base 00000000, size 128MB 
[    0.230000] SDRAM_CS1 ....disable
[    0.230000] SDRAM_CS2 ....disable
[    0.230000] SDRAM_CS3 ....disable
[    0.230000] PEX0_MEM ....base e0000000, size 128MB 
[    0.230000] PEX0_IO ....base f2000000, size   1MB 
[    0.230000] PEX1_MEM ....no such
[    0.230000] PEX1_IO ....no such
[    0.230000] INTER_REGS ....base f1000000, size   1MB 
[    0.230000] NFLASH_CS ....base fa000000, size   2MB 
[    0.230000] SPI_CS ....base f4000000, size  16MB 
[    0.230000] BOOT_ROM_CS ....no such
[    0.230000] DEV_BOOTCS ....no such
[    0.230000] CRYPT_ENG ....base f0000000, size   2MB 
[    0.230000] 
[    0.230000]   Marvell Development Board (LSP Version KW_LSP_5.1.3_patch18)-- SHEEVA PLUG  Soc: 88F6192 A1 LE
[    0.230000] 
[    0.230000]  Detected Tclk 166666667 and SysClk 200000000 
[    0.230000] Marvell USB EHCI Host controller #0: c403e740
[    0.730000] PEX0 interface detected Link X1
[    0.740000] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[    0.740000] pci 0000:00:01.0: PME# disabled
[    0.740000] PCI: bus0: Fast back to back transfers disabled
[    0.740000] mvPexLocalBusNumSet: ERR. Invalid PEX interface 1
[    0.750000] bio: create slab <bio-0> at 0
[    0.750000] SCSI subsystem initialized
[    0.750000] usbcore: registered new interface driver usbfs
[    0.750000] usbcore: registered new interface driver hub
[    0.750000] usbcore: registered new device driver usb
[    0.750000] NET: Registered protocol family 2
[    0.750000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.750000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    0.750000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[    0.750000] TCP: Hash tables configured (established 4096 bind 4096)
[    0.750000] TCP reno registered
[    0.750000] NET: Registered protocol family 1
[    0.750000] cpufreq: Init kirkwood cpufreq driver
[    0.760000] XOR registered 4 channels
[    0.760000] XOR 2nd invalidate WA enabled
[    0.760000] cesadev_init(c000d7fc)
[    0.760000] mvCesaInit: sessions=640, queue=64, pSram=f0000000
[    0.760000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.770000] msgmni has been set to 231
[    0.770000] alg: No test for cipher_null (cipher_null-generic)
[    0.770000] alg: No test for ecb(cipher_null) (ecb-cipher_null)
[    0.770000] alg: No test for digest_null (digest_null-generic)
[    0.770000] alg: No test for compress_null (compress_null-generic)
[    0.780000] alg: No test for stdrng (krng)
[    0.780000] alg: No test for hmac(digest_null) (hmac(digest_null-generic))
[    0.790000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.790000] io scheduler noop registered
[    0.790000] io scheduler anticipatory registered (default)
[    0.790000] Initializing ths8200_init
[    0.790000] Initializing dove_adi9889_init
[    0.810000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.810000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[    0.810000] console [ttyS0] enabled
[    0.820000] 
[    0.820000] Warning Sata is Powered Off
[    0.820000] Loading Marvell Ethernet Driver:
[    0.830000]   o Cached descriptors in DRAM
[    0.830000]   o DRAM SW cache-coherency
[    0.840000]   o 1 Giga ports supported
[    0.840000]   o Single RX Queue support - ETH_DEF_RXQ=0
[    0.840000]   o Single TX Queue support - ETH_DEF_TXQ=0
[    0.850000]   o TCP segmentation offload (TSO) supported
[    0.850000]   o Large Receive offload (LRO) supported
[    0.860000]   o Receive checksum offload supported
[    0.860000]   o Transmit checksum offload supported
[    0.870000]   o Network Fast Processing (Routing) supported - (Disabled)
[    0.880000]   o Driver ERROR statistics enabled
[    0.880000]   o Proc tool API enabled
[    0.880000]   o SKB Reuse supported - (Disabled)
[    0.890000]   o SKB Recycle supported - (Disabled)
[    0.890000]   o Rx descripors: q0=128
[    0.900000]   o Tx descripors: q0=532
[    0.900000]   o Loading network interface(s):
[    0.910000]      o register under mv88fx_eth platform
[    0.910000]      o eth0, ifindex = 2, GbE port = 0
[    0.920000] 
[    0.920000] mvFpRuleDb (c4347000): 1024 entries, 4096 bytes
[    0.920000] Counter=0, opIdx=6, overhead=16
[    0.930000] Counter=1, opIdx=2, overhead=0
[    0.930000] Counter=2, opIdx=1, overhead=18
[    0.940000] Counter=3, opIdx=2, overhead=0
[    0.940000] tun: Universal TUN/TAP device driver, 1.6
[    0.950000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.950000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit)
[    0.960000] Scanning device for bad blocks
[    1.010000] Using static partition definition
[    1.020000] Creating 5 MTD partitions on "nand_mtd":
[    1.020000] 0x000000000000-0x000000200000 : "u-boot"
[    1.030000] 0x000000200000-0x000000500000 : "uImage"
[    1.030000] 0x000000500000-0x000000800000 : "uImage2"
[    1.040000] 0x000000800000-0x000001000000 : "failsafe"
[    1.040000] 0x000001000000-0x000008000000 : "root"
[    1.050000] UBI: attaching mtd4 to ubi0
[    1.050000] UBI: physical eraseblock size:   131072 bytes (128 KiB)
[    1.060000] UBI: logical eraseblock size:    126976 bytes
[    1.070000] UBI: smallest flash I/O unit:    2048
[    1.070000] UBI: sub-page size:              512
[    1.080000] UBI: VID header offset:          2048 (aligned 2048)
[    1.080000] UBI: data offset:                4096
[    1.310000] UBI: attached mtd4 to ubi0
[    1.320000] UBI: MTD device name:            "root"
[    1.320000] UBI: MTD device size:            112 MiB
[    1.330000] UBI: number of good PEBs:        896
[    1.330000] UBI: number of bad PEBs:         0
[    1.340000] UBI: max. allowed volumes:       128
[    1.340000] UBI: wear-leveling threshold:    4096
[    1.340000] UBI: number of internal volumes: 1
[    1.350000] UBI: number of user volumes:     1
[    1.350000] UBI: available PEBs:             0
[    1.360000] UBI: total number of reserved PEBs: 896
[    1.360000] UBI: number of PEBs reserved for bad PEB handling: 8
[    1.370000] UBI: max/mean erase counter: 1/0
[    1.370000] UBI: image sequence number: 0
[    1.380000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.380000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
[    1.390000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
[    1.400000] UBI: background thread "ubi_bgt0d" started, PID 446
[    1.430000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
[    1.450000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00
[    1.450000] usb usb1: configuration #1 chosen from 1 choice
[    1.460000] hub 1-0:1.0: USB hub found
[    1.460000] hub 1-0:1.0: 1 port detected
[    1.470000] xhci_hcd 0000:00:01.0: xHCI Host Controller
[    1.470000] xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 2
[    1.480000] xhci_hcd 0000:00:01.0: irq 9, io mem 0xe0000000
[    1.490000] usb usb2: config 1 interface 0 altsetting 0 endpoint 0x81 has no SuperSpeed companion descriptor
[    1.500000] usb usb2: configuration #1 chosen from 1 choice
[    1.500000] hub 2-0:1.0: USB hub found
[    1.510000] hub 2-0:1.0: 4 ports detected
[    1.510000] Initializing USB Mass Storage driver...
[    1.510000] usbcore: registered new interface driver usb-storage
[    1.520000] USB Mass Storage support registered.
[    1.530000] usbcore: registered new interface driver ums-datafab
[    1.530000] usbcore: registered new interface driver ums-freecom
[    1.540000] usbcore: registered new interface driver ums-jumpshot
[    1.540000] usbcore: registered new interface driver ums-sddr09
[    1.550000] usbcore: registered new interface driver ums-sddr55
[    1.560000] usbcore: registered new interface driver ums-usbat
[    1.560000] mice: PS/2 mouse device common for all mice
[    1.570000] i2c /dev entries driver
[    1.580000] sdhci: Secure Digital Host Controller Interface driver
[    1.580000] sdhci: Copyright(c) Pierre Ossman
[    1.590000] mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
[    1.600000] usbcore: registered new interface driver usbhid
[    1.600000] usbhid: v2.6:USB HID core driver
[    1.610000] TCP cubic registered
[    1.610000] NET: Registered protocol family 17
[    1.620000] RPC: Registered udp transport module.
[    1.620000] RPC: Registered tcp transport module.
[    1.630000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.700000] UBIFS: recovery needed
[    1.790000] UBIFS: recovery completed
[    1.790000] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    1.800000] UBIFS: file system size:   110850048 bytes (108252 KiB, 105 MiB, 873 LEBs)
[    1.800000] UBIFS: journal size:       9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
[    1.810000] UBIFS: media format:       w4/r0 (latest is w4/r0)
[    1.820000] UBIFS: default compressor: lzo
[    1.820000] UBIFS: reserved for root:  0 bytes (0 KiB)
[    1.830000] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    1.830000] Freeing init memory: 124K
[    1.860000] mmc0: new high speed SDHC card at address e2cf
[    1.880000] mmcblk0: mmc0:e2cf SU08G 7.40 GiB 
[    1.880000]  mmcblk0: p1
[    4.200000] eth0: link down
[    4.200000] eth0: started
udhcpc: option -h NAME is deprecated, use -x hostname:NAME
udhcpc (v1.21.1) started
HWADDR 00 0x25 0x31 0x05 0xf5 0x25
PIP0 245
PIP1 37
cat: can't open '/etc/resolv.conf': No such file or directory
route: SIOCDELRT: No such process
grep: /etc/resolv.conf: No such file or directory
Sending discover...
[    6.140000] eth0: link up, full duplex, speed 1 Gbps
Sending discover...
Sending select for 10.0.1.231...
Lease of 10.0.1.231 obtained, lease time 86400
HWADDR 00 0x25 0x31 0x05 0xf5 0x25
PIP0 245
PIP1 37
route: SIOCDELRT: No such process
Loading gpio_keys.ko...
Loading ejectbutton.ko...
[    7.590000] IRQ 93 uses trigger mode 0; requested 3
[    7.590000] input: gpio-keys as /devices/platform/gpio-keys.0/input/input0
[    7.600000] xce_ebtn: Pogoplug series V4 eject button initialized.
[    7.740000] ufsd: module license 'Commercial product' taints kernel.
[    7.750000] Disabling lock debugging due to kernel taint
[    7.780000] ufsd: driver (8.6 (U86_S[2012-02-28-18:39:23]), LBD=ON, delalloc, ioctl) loaded at bf00c000
[    7.780000] NTFS support included
[    7.780000] Hfs+/HfsX support included
[    7.780000] For 'CloudEngines_PogoPlug_2011-08-03'
Loading rt3070sta.ko:        [    8.120000] rtusb init rt2870 --->
[    8.120000] usbcore: registered new interface driver rt2870
Success
Loading xce.ko:              [    8.140000] Cloud Engines XCE Init [Version: 3.9.0.4]
[    8.150000] XCE: CPU MEMORY MAP:
[    8.150000] XCE:   -- 0x00001000 - 0xbeffffff (3055 MB)  User Space Mappings
[    8.160000] XCE:   -- 0xbf000000 - 0xbfffffff (  16 MB)  Kernel module space
[    8.170000] XCE:   -- 0xc0000000 - 0xc7ffffff ( 128 MB)  Kernel direct-mapped ram
[    8.170000] XCE:   -- 0xc8800000 - 0xe7ffffff ( 504 MB)  Kernel vmalloc space
[    8.180000] XCE:   -- 0xe8000000 - 0xfeffffff ( 367 MB)  Kernel platform space
[    8.190000] XCE: CPU FEATURES:
[    8.190000] XCE:   -- I Cache:         enabled
[    8.200000] XCE:   -- D Cache:         enabled
[    8.200000] XCE:   -- Branch Predict:  enabled
[    8.200000] XCE:   -- MMU:             enabled
[    8.210000] XCE:   -- Alignment Abort: enabled
[    8.210000] XCE: BLPARAMS:   -- Loading properties [c4b23efc].
[    8.220000] XCE: BLPARAMS:   -- MTD @ [c4343000].
[    8.230000] XCE: BLPARAMS: Locating parameter block...
[    8.230000] XCE: BLPARAMS: reading 2048 bytes @ a0000
[    8.240000] XCE: Loaded Property Size: 2048
[    8.240000] XCE:    - 'cesvcid' -> '2W8WWQ4MZYQW3RPV68JJC7JZES'
[    8.250000] XCE:    - 'ceboardver' -> 'PPV4A3'
[    8.250000] XCE:   -- ICache Prefetch: enabled
[    8.260000] XCE:   -- DCache Prefetch: enabled
[    8.260000] XCE:   -- L2 Cache:        enabled
[    8.270000] XCE:   -- L2 Prefetch:     disabled
[    8.270000] XCE:   -- L2 Writethrough: disabled
[    8.280000] XCE:   -- Write Allocate:  disabled
[    8.280000] XCE:   -- Streaming:       disabled
[    8.280000] XCE: Current GPIO State:
[    8.290000] XCE:  GPIO L OUT:    0x21400000
[    8.290000] XCE:  GPIO L OE:     0x30000000
[    8.300000] XCE:  GPIO L BLINK:  0x00000000
[    8.300000] XCE:  GPIO L POL:    0x00000000
[    8.300000] XCE:  GPIO L IN:     0x01400000
[    8.310000] XCE:  GPIO H OUT:    0xfffc7fff
[    8.310000] XCE:  GPIO H OE:     0x00000000
[    8.320000] XCE:  GPIO H BLINK:  0x00004000
[    8.320000] XCE:  GPIO H POL:    0x00000000
[    8.330000] XCE:  GPIO H IN:     0x0000000f
Success
Starting hbplug:             Success
/ # [    8.510000] XCE: BLPARAMS:   -- Loading properties [c4b07ecc].
[    8.520000] XCE: BLPARAMS:   -- MTD @ [c4343000].
[    8.520000] XCE: BLPARAMS: Locating parameter block...
[    8.530000] XCE: BLPARAMS: reading 2048 bytes @ a0000
[    8.530000] XCE: BLPARAMS: reading 2048 bytes @ a0800
[    8.540000] XCE: BLPARAMS: reading 2048 bytes @ a1000
[    8.550000] XCE: BLPARAMS: reading 2048 bytes @ a1800
[   16.780000] XCE: XCE: LED -> DISCONNECTED
[   16.950000] EXT3-fs: INFO: recovery required on readonly filesystem.
[   16.950000] EXT3-fs: write access will be enabled during recovery.
[   18.510000] kjournald starting.  Commit interval 5 seconds
[   18.520000] EXT3-fs: recovery complete.
[   18.530000] EXT3-fs: mounted filesystem with writeback data mode.
[   18.780000] kjournald starting.  Commit interval 5 seconds
[   18.790000] EXT3 FS on mmcblk0p1, internal journal
[   18.790000] EXT3-fs: mounted filesystem with writeback data mode.

/tmp # /tmp/fw_printenv
baudrate=115200
bootcmd_mmc=run mmc_init; run set_bootargs_mmc; run mmc_boot
bootcmd_sata=run sata_init; run set_bootargs_sata; run sata_boot;
bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot;
bootdelay=10
console=ttyS0,115200
device=0:1
ethact=egiga0
if_netconsole=ping $serverip
led_error=orange blinking
led_exit=green off
led_init=green blinking
mainlineLinux=yes
mmc_boot=mw 0x800000 0 1; run mmc_load_uimage; if run mmc_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
mmc_init=mmc rescan
mmc_load_uimage=ext2load mmc $device 0x800000 /boot/uImage
mmc_load_uinitrd=ext2load mmc $device 0x1100000 /boot/uInitrd
mmc_root=/dev/mmcblk0p1
mtdids=nand0=orion_nand
partition=nand0,2
preboot_nc=run if_netconsole start_netconsole
rootdelay=10
rootfstype=ext3
sata_boot=mw 0x800000 0 1; run sata_load_uimage; if run sata_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
sata_init=ide reset
sata_load_uimage=ext2load ide $device 0x800000 /boot/uImage
sata_load_uinitrd=ext2load ide $device 0x1100000 /boot/uInitrd
sata_root=/dev/sda1
set_bootargs_mmc=setenv bootargs console=$console root=$mmc_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
set_bootargs_sata=setenv bootargs console=$console root=$sata_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
start_netconsole=setenv ncip $serverip; setenv bootdelay 10; setenv stdin nc; setenv stdout nc; setenv stderr nc; version;
stderr=serial
stdin=serial
stdout=serial
usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
usb_init=usb start
usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage
usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd
usb_root=/dev/sda1
ethaddr=00:25:31:05:f5:25
arcNumber=3960
machid=F78
usb_rootfstype=ext3
mtdparts=mtdparts=orion_nand:2M(u-boot),3M(uImage),3M(uImage2),8M(failsafe),112M(root)
bootcmd_pogo=if ubi part root 2048 && ubifsmount ubi:rootfs && ubifsload 0x800000 uboot.mtd0.dockstar.original.kwb ; then go 0x800200; fi
bootcmd=run bootcmd_mmc; run bootcmd_usb; run bootcmd_sata; run bootcmd_pogo; reset
serverip=10.0.1.231
ipaddr=10.0.1.220

        __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_ 
| | | |___|  _ \ / _ \ / _ \| __| 
| |_| |___| |_) | (_) | (_) | |_ 
 \___/    |____/ \___/ \___/ \__| 
 ** MARVELL BOARD: RD-88F6281A LE 

U-Boot 1.1.4 (Sep  4 2009 - 09:36:11) Marvell version: 3.4.14

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CEE60

Soc: 88F6281 A0 (DDR2)
CPU running @ 1000Mhz L2 running @ 333Mhz
SysClock = 333Mhz , TClock = 200Mhz 

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size  64MB 
DRAM CS[1] base 0x04000000   size  64MB 
DRAM Total size 128MB  16bit width
Flash:  0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB
CRC in Flash: ffffffff, Calculated CRC: 619d86db
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++Checksum Error!++++++++++++++++++++++++++++++
## Error: environment overflow, "stdin" deleted
## Error: environment overflow, "stdout" deleted
## Error: environment overflow, "stderr" deleted

CPU : Marvell Feroceon (Rev 1)
## Error: environment overflow, "console" deleted
## Error: environment overflow, "mainlineLinux" deleted
## Error: environment overflow, "CASset" deleted
## Error: environment overflow, "enaMonExt" deleted
## Error: environment overflow, "enaCpuStream" deleted
## Error: environment overflow, "enaWrAllo" deleted
## Error: environment overflow, "pexMode" deleted
## Error: environment overflow, "disL2Cache" deleted
## Error: environment overflow, "setL2CacheWT" deleted
## Error: environment overflow, "disL2Prefetch" deleted
## Error: environment overflow, "enaICPref" deleted
## Error: environment overflow, "enaDCPref" deleted
## Error: environment overflow, "sata_dma_mode" deleted
## Error: environment overflow, "MALLOC_len" deleted
## Error: environment overflow, "ethprime" deleted
## Error: environment overflow, "netbsd_en" deleted
## Error: environment overflow, "vxworks_en" deleted
## Error: environment overflow, "bootargs_root" deleted
## Error: environment overflow, "bootargs_end" deleted
## Error: environment overflow, "image_name" deleted
## Error: environment overflow, "bootcmd" deleted
## Error: environment overflow, "standalone" deleted
## Error: environment overflow, "bootdelay" deleted
## Error: environment overflow, "disaMvPnp" deleted
## Error: environment overflow, "disaMvPnp" deleted
## Error: environment overflow, "ethaddr" deleted
## Error: environment overflow, "ethmtu" deleted
## Error: environment overflow, "eth1addr" deleted
## Error: environment overflow, "eth1mtu" deleted
## Error: environment overflow, "mvPhoneConfig" deleted
## Error: environment overflow, "mvNetConfig" deleted
## Error: environment overflow, "usb0Mode" deleted
## Error: environment overflow, "yuk_ethaddr" deleted
## Error: environment overflow, "nandEcc" deleted
## Error: environment overflow, "hddPowerCtrl" deleted
## Error: environment overflow, "netretry" deleted
## Error: environment overflow, "rcvrip" deleted
## Error: environment overflow, "loadaddr" deleted
## Error: environment overflow, "autoload" deleted
## Error: environment overflow, "enaAutoRecovery" deleted

Streaming disabled 
Write allocate disabled

Module 0 is RGMII
Module 1 is TDM

USB 0: device mode
PEX 0: interface detected no Link.
Net:   ## Error: environment overflow, "ethact" deleted
egiga0, egiga1## Error: environment overflow, "ethact" deleted

USB:   scanning bus for devices... 1 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
Aquiring an IP address using DHCP...
## Error: environment overflow, "ethact" deleted
*** ERROR: `ethaddr' not set
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
## Error: environment overflow, "ethact" deleted
*** ERROR: `ethaddr' not set
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
## Error: environment overflow, "ethact" deleted
*** ERROR: `ethaddr' not set
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
Failed to retreive an IP address assuming default (<NULL>)!
Starting the Recovery process to retreive the file...
## Error: environment overflow, "ethact" deleted
*** ERROR: `ethaddr' not set
## Error: environment overflow, "ethact" deleted
egiga1 no link
## Error: environment overflow, "ethact" deleted
Failed
Power Button is pressed!
MPP Sel: 00000530, Data IN Enable: 00020058, Data In Polarity: 00000040, Data In: 00000011
Power Button is released!
MAC: 00:01:01:E9:34:80, IP: 10.233.52.128
## Error: environment overflow, "ethaddr" deleted
## Error: environment overflow, "ipaddr" deleted
## Error: environment overflow, "serverip" deleted
## Error: environment overflow, "netmask" deleted
## Error: environment overflow, "image_name" deleted
## Error: environment overflow, "console" deleted
## Error: environment overflow, "bootargs_root" deleted
## Error: environment overflow, "rootpath" deleted
## Error: environment overflow, "ethact" deleted
*** ERROR: `serverip' not set
## Error: environment overflow, "bootargs" deleted
## Booting image at 00800000 ...
Bad Magic Number
Marvell>>

root@lenovo-debian:/home/joker/Downloads/kwboot-tool# ./kwboot -t /dev/ttyUSB0 -b uboot.2017.07-tld-1.netgear_ms2110.mtd0.kwb -p
Sending boot message. Please reboot the target...

auto lo eth0
iface lo inet loopback
iface eth0 inet static
        address 192.168.100.152
        netmask 255.255.255.0
        network 192.168.100.0
        broadcast 192.168.100.255
        gateway 192.168.100.1

allow-hotplug wlxxxxxxxxxxxxx
auto wlxxxxxxxxxxxxx
iface wlxxxxxxxxxxxxx inet static
	address 192.168.100.153
        netmask 255.255.255.0
        network 192.168.100.0
        broadcast 192.168.100.255
        gateway 192.168.100.1
	wpa-ssid myrouter
	wpa-psk xxxxxxxxx

Quote

dev: size erasesize name
mtd0: 00e00000 00020000 "boot"
mtd1: 07200000 00020000 "data"

Quote

root@PogoplugPro:/tmp# cat /proc/mtd
dev: size erasesize name
mtd0: 08000000 00020000 "NAND 128MiB 3,3V 8-bit"
mtd1: 00e00000 00020000 "boot"
mtd2: 07200000 00020000 "rootfs"

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.2.9-kirkwood-tld-1 (root@tldDebian) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1)) #1 PREEMPT Sat Aug 17 15:00:56 PDT 2019
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] OF: fdt: Machine model: ZyXEL NSA325
[    0.000000] Memory policy: Data cache writeback
[    0.000000] On node 0 totalpages: 131072
[    0.000000]   Normal zone: 1024 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 131072 pages, LIFO batch:31
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 130048
[    0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x100000(uboot),0x80000(stock_uboot_env),0x80000(key_store),0x80000(info),0xA00000(etc),0xA00000(kernel_1),0x2FC0000(rootfs1),0xA00000(kernel_2),0x2FC0000(rootfs2) init=/bin/systemd
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 494676K/524288K available (9216K kernel code, 868K rwdata, 3400K rodata, 1024K init, 301K bss, 29612K reserved, 0K cma-reserved)
[    0.000000] random: get_random_u32 called from cache_alloc_refill+0x38c/0x928 with crng_init=0
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] 	Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[    0.000008] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[    0.000039] Switching to timer-based delay loop, resolution 5ns
[    0.000644] Console: colour dummy device 80x30
[    0.000688] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000)
[    0.000709] pid_max: default: 32768 minimum: 301
[    0.001010] LSM: Security Framework initializing
[    0.001162] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.001184] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.001888] *** VALIDATE proc ***
[    0.002110] *** VALIDATE cgroup1 ***
[    0.002131] *** VALIDATE cgroup2 ***
[    0.002214] CPU: Testing write buffer coherency: ok
[    0.003675] Setting up static identity map for 0x100000 - 0x100058
[    0.003935] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1
[    0.004180] rcu: Hierarchical SRCU implementation.
[    0.006811] devtmpfs: initialized
[    0.012272] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.012298] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.012511] xor: measuring software checksum speed
[    0.110097]    arm4regs  :  1452.800 MB/sec
[    0.210065]    8regs     :   872.400 MB/sec
[    0.310061]    32regs    :  1268.400 MB/sec
[    0.310077] xor: using function: arm4regs (1452.800 MB/sec)
[    0.310095] prandom: seed boundary self test passed
[    0.313228] prandom: 100 self tests passed
[    0.313238] pinctrl core: initialized pinctrl subsystem
[    0.314465] NET: Registered protocol family 16
[    0.314900] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.315549] audit: initializing netlink subsys (disabled)
[    0.316591] audit: type=2000 audit(0.310:1): state=initialized audit_enabled=0 res=1
[    0.316695] cpuidle: using governor ladder
[    0.316760] cpuidle: using governor menu
[    0.317230] Feroceon L2: Enabling L2
[    0.317271] Feroceon L2: Cache support initialised.
[    0.322068] No ATAGs?
[    2.560046] random: fast init done
[    4.743667] alg: No test for lzo-rle (lzo-rle-generic)
[    4.743950] alg: No test for lzo-rle (lzo-rle-scomp)
[    4.920382] raid6: int32x8  gen()   171 MB/s
[    5.090131] raid6: int32x8  xor()   115 MB/s
[    5.260378] raid6: int32x4  gen()   173 MB/s
[    5.430160] raid6: int32x4  xor()   112 MB/s
[    5.600118] raid6: int32x2  gen()   177 MB/s
[    5.770049] raid6: int32x2  xor()   125 MB/s
[    5.940334] raid6: int32x1  gen()   134 MB/s
[    6.110342] raid6: int32x1  xor()    92 MB/s
[    6.110351] raid6: using algorithm int32x2 gen() 177 MB/s
[    6.110358] raid6: .... xor() 125 MB/s, rmw enabled
[    6.110364] raid6: using intx1 recovery algorithm
[    6.110584] vgaarb: loaded
[    6.110987] SCSI subsystem initialized
[    6.111182] libata version 3.00 loaded.
[    6.111392] usbcore: registered new interface driver usbfs
[    6.111440] usbcore: registered new interface driver hub
[    6.111506] usbcore: registered new device driver usb
[    6.111652] pps_core: LinuxPPS API ver. 1 registered
[    6.111661] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    6.111681] PTP clock support registered
[    6.112744] clocksource: Switched to clocksource orion_clocksource
[    6.886671] VFS: Disk quotas dquot_6.6.0
[    6.886757] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    6.894285] NET: Registered protocol family 2
[    6.894952] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes)
[    6.894984] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    6.895038] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[    6.895089] TCP: Hash tables configured (established 4096 bind 4096)
[    6.895164] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    6.895188] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    6.895375] NET: Registered protocol family 1
[    6.895906] RPC: Registered named UNIX socket transport module.
[    6.895917] RPC: Registered udp transport module.
[    6.895924] RPC: Registered tcp transport module.
[    6.895931] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    6.895943] PCI: CLS 0 bytes, default 32
[    6.896140] Trying to unpack rootfs image as initramfs...
[    7.539872] Freeing initrd memory: 9488K
[    7.540047] NetWinder Floating Point Emulator V0.97 (double precision)
[    7.541082] Initialise system trusted keyrings
[    7.541123] Key type blacklist registered
[    7.541315] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[    7.541403] zbud: loaded
[    7.542292] NFS: Registering the id_resolver key type
[    7.542316] Key type id_resolver registered
[    7.542324] Key type id_legacy registered
[    7.542341] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    7.542354] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    7.542593] jffs2: version 2.2. (NAND) (SUMMARY)  \xc2\xa9 2001-2006 Red Hat, Inc.
[    7.542843] fuse: init (API version 7.31)
[    7.543192] orangefs_debugfs_init: called with debug mask: :none: :0:
[    7.543340] orangefs_init: module version upstream loaded
[    7.543350] SGI XFS with ACLs, security attributes, realtime, scrub, no debug enabled
[    7.556938] async_tx: api initialized (async)
[    7.556959] Key type asymmetric registered
[    7.556967] Asymmetric key parser 'x509' registered
[    7.557030] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[    7.558192] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[    7.559723] mvebu-pcie mbus@f1000000:pcie@82000000: PCI host bridge to bus 0000:00
[    7.559742] pci_bus 0000:00: root bus resource [bus 00-ff]
[    7.559754] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
[    7.559764] pci_bus 0000:00: root bus resource [io  0x1000-0xeffff]
[    7.559775] pci_bus 0000:00: scanning bus
[    7.559870] pci 0000:00:01.0: [11ab:6282] type 01 class 0x060400
[    7.559904] pci 0000:00:01.0: reg 0x38: [mem 0x00000000-0x000007ff pref]
[    7.561092] pci_bus 0000:00: fixups for bus
[    7.561103] PCI: bus0: Fast back to back transfers disabled
[    7.561118] pci 0000:00:01.0: scanning [bus 00-00] behind bridge, pass 0
[    7.561125] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    7.561140] pci 0000:00:01.0: scanning [bus 00-00] behind bridge, pass 1
[    7.561245] pci_bus 0000:01: scanning bus
[    7.561283] pci 0000:01:00.0: [1033:0194] type 00 class 0x0c0330
[    7.561330] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00001fff 64bit]
[    7.561470] pci 0000:01:00.0: PME# supported from D0 D3hot
[    7.561484] pci 0000:01:00.0: PME# disabled
[    7.561538] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
[    7.583831] pci_bus 0000:01: fixups for bus
[    7.583844] PCI: bus1: Fast back to back transfers disabled
[    7.583856] pci_bus 0000:01: bus scan returning with max=01
[    7.583866] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    7.583879] pci_bus 0000:00: bus scan returning with max=01
[    7.584023] pci 0000:00:01.0: BAR 14: assigned [mem 0xe0000000-0xe00fffff]
[    7.584037] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0100000-0xe01007ff pref]
[    7.584053] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe0001fff 64bit]
[    7.584074] pci 0000:00:01.0: PCI bridge to [bus 01]
[    7.584089] pci 0000:00:01.0:   bridge window [mem 0xe0000000-0xe00fffff]
[    7.584168] pcieport 0000:00:01.0: assign IRQ: got 0
[    7.584183] pcieport 0000:00:01.0: enabling device (0140 -> 0142)
[    7.584205] pcieport 0000:00:01.0: enabling bus mastering
[    7.584239] pci 0000:00:01.0: enabling bus mastering
[    7.584250] pci 0000:01:00.0: enabling device (0140 -> 0142)
[    7.584713] mv_xor f1060800.xor: Marvell shared XOR driver
[    7.643400] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    7.644940] mv_xor f1060900.xor: Marvell shared XOR driver
[    7.703362] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy intr )
[    7.705145] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    7.706193] printk: console [ttyS0] disabled
[    7.706257] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A
[    8.629873] printk: console [ttyS0] enabled
[    8.640676] loop: module loaded
[    8.644834] sata_mv f1080000.sata: version 1.28
[    8.645061] sata_mv f1080000.sata: slots 32 ports 2
[    8.652835] scsi host0: sata_mv
[    8.657137] scsi host1: sata_mv
[    8.661231] ata1: SATA max UDMA/133 irq 32
[    8.666093] ata2: SATA max UDMA/133 irq 32
[    8.671716] nand: device found, Manufacturer ID: 0x92, Chip ID: 0xf1
[    8.678897] nand: Eon NAND 128MiB 3,3V 8-bit
[    8.683905] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    8.692212] Scanning device for bad blocks
[    8.697120] 9 cmdlinepart partitions found on MTD device orion_nand
[    8.704131] Creating 9 MTD partitions on "orion_nand":
[    8.709997] 0x000000000000-0x000000100000 : "uboot"
[    8.716652] 0x000000100000-0x000000180000 : "stock_uboot_env"
[    8.724121] 0x000000180000-0x000000200000 : "key_store"
[    8.731005] 0x000000200000-0x000000280000 : "info"
[    8.737506] 0x000000280000-0x000000c80000 : "etc"
[    8.743923] 0x000000c80000-0x000001680000 : "kernel_1"
[    8.750751] 0x000001680000-0x000004640000 : "rootfs1"
[    8.757629] 0x000004640000-0x000005040000 : "kernel_2"
[    8.764493] 0x000005040000-0x000008000000 : "rootfs2"
[    8.772268] libphy: Fixed MDIO Bus: probed
[    8.777756] libphy: orion_mdio_bus: probed
[    8.793925] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    8.801826] mv643xx_eth_port mv643xx_eth_port.0: DMA mask not set
[    8.809444] mv643xx_eth: Set the PHY to fix link down
[    8.809921] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 4c:9e:ff:0f:93:7b
[    8.825357] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    8.832635] ehci-pci: EHCI PCI platform driver
[    8.837890] ehci-orion: EHCI orion driver
[    8.842811] orion-ehci f1050000.ehci: EHCI Host Controller
[    8.849035] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[    8.857572] orion-ehci f1050000.ehci: irq 30, io mem 0xf1050000
[    8.892784] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[    8.899754] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02
[    8.908795] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    8.916780] usb usb1: Product: EHCI Host Controller
[    8.922398] usb usb1: Manufacturer: Linux 5.2.9-kirkwood-tld-1 ehci_hcd
[    8.929767] usb usb1: SerialNumber: f1050000.ehci
[    8.935683] hub 1-0:1.0: USB hub found
[    8.940179] hub 1-0:1.0: 1 port detected
[    8.945440] xhci_hcd 0000:01:00.0: assign IRQ: got 36
[    8.945504] xhci_hcd 0000:01:00.0: enabling bus mastering
[    8.945514] xhci_hcd 0000:01:00.0: xHCI Host Controller
[    8.951512] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[    8.959959] xhci_hcd 0000:01:00.0: hcc params 0x014042cb hci version 0x96 quirks 0x0000000000000004
[    8.969803] xhci_hcd 0000:01:00.0: enabling Mem-Wr-Inval
[    8.970210] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.02
[    8.979247] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    8.987234] usb usb2: Product: xHCI Host Controller
[    8.992867] usb usb2: Manufacturer: Linux 5.2.9-kirkwood-tld-1 xhci-hcd
[    9.000232] usb usb2: SerialNumber: 0000:01:00.0
[    9.006095] hub 2-0:1.0: USB hub found
[    9.010596] hub 2-0:1.0: 2 ports detected
[    9.015804] xhci_hcd 0000:01:00.0: xHCI Host Controller
[    9.021761] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3
[    9.029949] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed
[    9.037049] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[    9.046021] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.02
[    9.055118] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    9.063084] usb usb3: Product: xHCI Host Controller
[    9.068682] usb usb3: Manufacturer: Linux 5.2.9-kirkwood-tld-1 xhci-hcd
[    9.076040] usb usb3: SerialNumber: 0000:01:00.0
[    9.081803] hub 3-0:1.0: USB hub found
[    9.086345] hub 3-0:1.0: 2 ports detected
[    9.091666] usbcore: registered new interface driver usb-storage
[    9.098726] mousedev: PS/2 mouse device common for all mice
[    9.105304] i2c /dev entries driver
[    9.115849] rtc-pcf8563 0-0051: registered as rtc0
[    9.123182] device-mapper: uevent: version 1.0.3
[    9.128793] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com
[    9.138317] device-mapper: multipath round-robin: version 1.2.0 loaded
[    9.145628] device-mapper: multipath queue-length: version 0.2.0 loaded
[    9.153001] device-mapper: multipath service-time: version 0.3.0 loaded
[    9.160403] device-mapper: dm-log-userspace: version 1.3.0 loaded
[    9.167352] device-mapper: raid: Loading target version 1.14.0
[    9.173956] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[    9.182730] hidraw: raw HID events driver (C) Jiri Kosina
[    9.189149] ata1.00: ATA-9: WDC WD20EFRX-68EUZN0, 82.00A82, max UDMA/133
[    9.197081] drop_monitor: Initializing network drop monitor service
[    9.204123] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[    9.212019] NET: Registered protocol family 17
[    9.217561] Key type dns_resolver registered
[    9.222838] ata1.00: configured for UDMA/133
[    9.228514] registered taskstats version 1
[    9.233350] Loading compiled-in X.509 certificates
[    9.239233] scsi 0:0:0:0: Direct-Access     ATA      WDC WD20EFRX-68E 0A82 PQ: 0 ANSI: 5
[    9.248256] zswap: loaded using pool lzo/zbud
[    9.255131] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB)
[    9.272896] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    9.280056] sd 0:0:0:0: [sda] Write Protect is off
[    9.292910] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    9.293059] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    9.312846] usb 1-1: new high-speed USB device number 2 using orion-ehci
[    9.358396]  sda: sda1
[    9.372315] Key type big_key registered
[    9.377367] sd 0:0:0:0: [sda] Attached SCSI disk
[    9.415906] Key type encrypted registered
[    9.423505] rtc-pcf8563 0-0051: setting system clock to 2021-01-19T21:02:18 UTC (1611090138)
[    9.524202] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=85.32
[    9.533168] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    9.541069] usb 1-1: Product: USB2.0 Hub
[    9.546444] hub 1-1:1.0: USB hub found
[    9.551217] hub 1-1:1.0: 4 ports detected
[    9.762774] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[    9.772207] ata2.00: ATA-9: WDC WD20EFRX-68EUZN0, 82.00A82, max UDMA/133
[    9.779717] ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[    9.789867] ata2.00: configured for UDMA/133
[    9.805301] scsi 1:0:0:0: Direct-Access     ATA      WDC WD20EFRX-68E 0A82 PQ: 0 ANSI: 5
[    9.815061] sd 1:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB)
[    9.823860] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[    9.829872] sd 1:0:0:0: [sdb] Write Protect is off
[    9.835420] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    9.835522] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    9.882778] usb 1-1.2: new high-speed USB device number 3 using orion-ehci
[    9.916225]  sdb: sdb1
[    9.920550] sd 1:0:0:0: [sdb] Attached SCSI disk
[    9.929000] Freeing unused kernel memory: 1024K
[    9.943261] Checked W+X mappings: passed, no W+X pages found
[    9.949645] Run /init as init process
[   10.040747] usb 1-1.2: New USB device found, idVendor=058f, idProduct=6387, bcdDevice= 1.06
[   10.062849] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   10.070912] usb 1-1.2: Product: Mass Storage
[   10.082824] usb 1-1.2: Manufacturer: Generic
[   10.088386] usb 1-1.2: SerialNumber: 671EAE92
[   10.120425] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[   10.152914] scsi host2: usb-storage 1-1.2:1.0
[   10.159952] usbcore: registered new interface driver uas
[   11.205037] scsi 2:0:0:0: Direct-Access     Generic  Flash Disk       8.07 PQ: 0 ANSI: 4
[   11.222255] sd 2:0:0:0: [sdc] 7864320 512-byte logical blocks: (4.03 GB/3.75 GiB)
[   11.239997] sd 2:0:0:0: [sdc] Write Protect is off
[   11.245602] sd 2:0:0:0: [sdc] Mode Sense: 23 00 00 00
[   11.246476] sd 2:0:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[   11.282564]  sdc: sdc1
[   11.296124] sd 2:0:0:0: [sdc] Attached SCSI removable disk
[   21.761121] EXT4-fs (sdc1): mounting ext3 file system using the ext4 subsystem
[   21.810180] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   25.046664] random: crng init done
[   25.302228] input: gpio_keys as /devices/platform/gpio_keys/input/input0
[   25.320173] systemd-udevd[396]: Using default interface naming scheme 'v240'.
[   25.426368] systemd-udevd[396]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[   26.062527] marvell-cesa f1030000.crypto: CESA device successfully registered
[   26.135726] systemd-udevd[378]: link_config: autonegotiation is unset or enabled, the speed and duplex are not writable.
[   26.197153] watchdog: f1020300.watchdog-timer: driver supplied timeout (4294967295) out of range
[   26.216152] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   26.251291] sd 1:0:0:0: Attached scsi generic sg1 type 0
[   26.266853] watchdog: f1020300.watchdog-timer: falling back to default timeout (21)
[   26.308450] sd 2:0:0:0: Attached scsi generic sg2 type 0
[   26.330271] orion_wdt: Initial timeout 21 sec
[   27.728005] EXT4-fs (sdc1): re-mounted. Opts: errors=remount-ro
[   30.550820] mv643xx_eth: Set the PHY back to auto-negotiation mode
[   31.651963] NET: Registered protocol family 10
[   31.665546] Segment Routing with IPv6
[   33.653547] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[   33.664173] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

Quote

#connect
screen /dev/ttyUSB0 115200,cs8,-parenb,-cstopb,-hupcl
#list partition
cat /proc/partitions
cat /proc/mtd
#remount / (root) as read/write
mount -o remount,rw /
#change root password
passwd root
#start telnetd or ssh server (both are already there)
#startup script can be found here
#(might want to enable dropbear and telnet and disable pogo services 'hbmgr.sh'):
vi /etc/init.d/rcS
#mount sdcard
mkdir /mnt/sdcard
mknod /dev/mmcblk0 b 179 0
mknod /dev/mmcblk0p1 b 179 1
mount /dev/mmcblk0p1 /mnt/sdcard
#mount USB drive
mkdir /mnt/usb
mknod /dev/sda b 8 0
mknod /dev/sda1 b 8 1
mount /dev/sda1 /mnt/usb
#add these lines to /etc/fstab
/dev/sda1 /mnt/usb vfat defaults 0 0
/dev/mmcblk0p1 /mnt/sdcard vfat defaults 0 0

Quote

busybox --list|while read c;do echo $c;ln -s /bin/busybox $c;done

Quote

baudrate=115200
----bootargs=console=ttyS0,115200 root=ubi0:rootfs ubi.mtd=4,2048 rootfstype=ubifs
----boot=bootm 0x800000
bootcmd=run boot_nand
bootdelay=1
----boot_nand=run load_nand boot || run load_nand2 boot
----CASset=min
----ceboardver=PPV4A3
----disaMvPnp=no
----disL2Cache=no
----disL2Prefetch=yes
----enaCpuStream=no
----enaDCPref=yes
----enaICPref=yes
----enaMonExt=no
----enaWrAllo=no
----Environment size: 801/131068 bytes
ethact=egiga0
----ethaddr=00:50:43:00:02:02
----ethmtu=1500
----ethprime=egiga0
----hddPowerCtrl=no
ipaddr=169.254.254.253
----load_nand2=nboot 0x800000 0 0x500000
----load_nand=nboot 0x800000 0 0x200000
----loads_echo=0
mainlineLinux=no
----MALLOC_len=1
----nandEcc=1bit
----netbsd_en=no
----netmask=255.255.0.0
----pcieTune=no
----pexMode=RC
----rootpath=/mnt/ARM_FS/
----run_diag=yes
----sata_dma_mode=yes
serverip=169.254.254.254
----setL2CacheWT=yes
stderr=serial
stdin=serial
stdout=serial
----usb0Mode=host
----vxworks_en=no

         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|
 ** MARVELL BOARD: RD-88F6281A LE

U-Boot 1.1.4 (Sep  4 2009 - 09:36:11) Marvell version: 3.4.14

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CEE60

Soc: 88F6281 A0 (DDR2)
CPU running @ 1000Mhz L2 running @ 333Mhz
SysClock = 333Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size  64MB
DRAM CS[1] base 0x04000000   size  64MB
DRAM Total size 128MB  16bit width
Flash:  0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB
CRC in Flash: beb3c296, Calculated CRC: beb3c296

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled

Module 0 is RGMII
Module 1 is TDM

USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0, egiga1 [PRIME]
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x100000, size 0x300000

Reading data from 0x3ff800 -- 100% complete.
 3145728 bytes read: OK
## Booting image at 00800000 ...
   Image Name:   Linux-2.6.22.18-Netgear
   Created:      2010-06-13  23:54:53 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2788728 Bytes =  2.7 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux............................................................................................................................................................ done, booting the kernel.
Linux version 2.6.22.18-Netgear (mostafah@es5x86.axentra.com) (gcc version 4.2.1) #16 Sun Jun 13 19:54:46 EDT 2010
CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053977
Machine: Feroceon-KW
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
Built 1 zonelists.  Total pages: 32512
Kernel command line: console=ttyS0,115200 ubi.mtd=2,2048 root=ubi0:rootfs rootfstype=ubifs init=/linuxrc
PID hash table entries: 512 (order: 9, 2048 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 64MB 64MB 0MB 0MB = 128MB total
Memory: 124800KB available (4048K code, 268K data, 692K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16

CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size  64MB
SDRAM_CS1 ....base 04000000, size  64MB
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e8000000, size 128MB
PEX0_IO ....base f2000000, size   1MB
INTER_REGS ....base f1000000, size   1MB
NFLASH_CS ....base fa000000, size   2MB
SPI_CS ....base f4000000, size  16MB
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT_ENG ....base f0000000, size   2MB

  Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21)-- RD-88F6281A  Soc: 88F6281 A0 LE

 Detected Tclk 200000000 and SysClk 333333333
MV Buttons Device Load
Marvell USB EHCI Host controller #0: c063d600
PEX0 interface detected no Link.
PCI: bus0: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
Time: kw_clocksource clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
RTC has been updated!!!
RTC registered
Use the XOR engines (acceleration) for enhancing the following functions:
  o RAID 5 Xor calculation
  o kernel memcpy
  o kenrel memzero
Number of XOR engines to use: 4
cesadev_init(c000eed0)
mvCesaInit: sessions=640, queue=64, pSram=f0000000
MV Buttons Driver Load
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
loop: module loaded
Loading Marvell Ethernet Driver:
  o Cached descriptors in DRAM
  o DRAM SW cache-coherency
  o Multi RX Queue support - 4 RX queues
  o Multi TX Queue support - 2 TX Queues
  o TCP segmentation offload enabled
  o Receive checksum offload enabled
  o Transmit checksum offload enabled
  o Network Fast Processing (Routing) supported
  o Network Fast Processing (NAT) supported
  o Driver ERROR statistics enabled
  o Driver INFO statistics enabled
  o Proc tool API enabled
  o Gateway support enabled
     o Using Marvell Header Mode
     o L2 IGMP support
  o Rx descripors: q0=128 q1=128 q2=128 q3=128
  o Tx descripors: q0=532 q1=532
  o Loading network interface(s):
    o eth0, ifindex = 1, GbE port = 0
    o eth1, ifindex = 2, GbE port = 1

mvFpRuleDb (c7977000): 1024 entries, 4096 bytes
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
Copyright (c) 1999-2006 Intel Corporation.
e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
Integrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
scsi 0:0:0:0: Direct-Access     WDC      WD10EAVS-00D7B1  01.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors (1000205 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors (1000205 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
 sda: sda1
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 368 at 0x02e00000
Bad eraseblock 369 at 0x02e20000
Bad eraseblock 618 at 0x04d40000
Bad eraseblock 700 at 0x05780000
Bad eraseblock 1012 at 0x07e80000
Bad eraseblock 1294 at 0x0a1c0000
Bad eraseblock 1393 at 0x0ae20000
Bad eraseblock 1444 at 0x0b480000
Bad eraseblock 1642 at 0x0cd40000
Bad eraseblock 2036 at 0x0fe80000
Using static partition definition
Creating 3 MTD partitions on "nand_mtd":
0x00000000-0x00100000 : "u-boot"
0x00100000-0x00700000 : "uImage"
0x00700000-0x10000000 : "root"
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    126976 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          2048 (aligned 2048)
UBI: data offset:                4096
UBI warning: ubi_eba_init_scan: cannot reserve enough PEBs for bad PEB handling, reserved 19, need 38
UBI: attached mtd2 to ubi0
UBI: MTD device name:            "root"
UBI: MTD device size:            249 MiB
UBI: number of good PEBs:        1982
UBI: number of bad PEBs:         10
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     1
UBI: available PEBs:             0
UBI: total number of reserved PEBs: 1982
UBI: number of PEBs reserved for bad PEB handling: 19
UBI: max/mean erase counter: 89/8
UBI: background thread "ubi_bgt0d" started, PID 291
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v3.0
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
raid6: int32x1     81 MB/s
raid6: int32x2     95 MB/s
raid6: int32x4    102 MB/s
raid6: int32x8     92 MB/s
raid6: using algorithm int32x4 (102 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: measuring checksumming speed
   arm4regs  :   903.600 MB/sec
   8regs     :   629.200 MB/sec
   32regs    :   750.000 MB/sec
raid5: using function: arm4regs (903.600 MB/sec)
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
dm_crypt using the OCF package.
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1024 buckets, 8192 max)
mvFpNatDb (c7f77000): 1024 entries, 4096 bytes
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NFP (fdb) init 256 entries, 1024 bytes
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
md: Autodetecting RAID arrays.
md: autorun ...
md: considering sda1 ...
md:  adding sda1 ...
md: created md0
md: bind<sda1>
md: running: <sda1>
raid1: raid set md0 active with 1 out of 2 mirrors
md: ... autorun DONE.
Freeing init memory: 692K
Reset button not pressed
Proceeding normally.
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size:   239857664 bytes (234236 KiB, 228 MiB, 1889 LEBs)
UBIFS: journal size:       9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
UBIFS: media format:       4 (latest is 4)
UBIFS: default compressor: zlib
UBIFS: reserved for root:  0 bytes (0 KiB)
   >> This is the point at which it freezes <<